Elcometer 3000 Series Bedienungsanleitung

User Guide

Elcometer 3000

Motorised and Manual

Clemen Unit

www.elcometer.com

Section

Page

Overview

en-2

Box Contents

en-3

Working Safely

en-3

Getting Started

en-4

Testing a Sample - Manual Clemen Unit

en-4

Testing a Sample - Motorised Clemen Unit

en-6

Spares & Accessories

en-9

Care & Maintenance

en-9

Warranty Statement

en-10

Technical Specification

en-10

Legal Notices & Regulatory Information

en-11

www.elcometer.com

For the avoidance of doubt, please refer to the original English language version.

Dimensions: Manual Clemen Unit: 410 x 200 x 155mm (16.1 x 7.9 x 6.1")

Motorised Clemen Unit: 460 x 280 x 330mm (18 x 11 x 13")

Weight: Manual Clemen Unit: 6kg (13.2lb)

Motorised Clemen Unit: 20kg (44lb)

transcribed, stored (in a retrieval system or otherwise) or translated into any language, in any form or by any

means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior written permission of

Elcometer Limited.

CONTENTS

en-1

1 OVERVIEW

www.elcometer.com en-2

Available in two versions; Manual and Motorised, the Elcometer 3000

Clemen Unit is a robust and simple-to-use instrument for evaluation of

the resistance to scratching of a coated surface. The sample can be

metal, wood, glass, plastic or other hard materials.

A tool fitted with a hemispherical ball is lowered gradually onto the

surface of the sample and moved in a straight line a distance of 60mm

(2.4"). The downward force exerted by the tool onto the surface is

adjustable by means of a sliding weight.

Depending on the purpose of the test and the force applied, varying

degrees of penetration of the tool into the coating are observed, from a

superficial trace to total destruction.

Elcometer 3000 Manual Clemen Unit: The sample is clamped

to a sliding platform which is moved manually.

Elcometer 3000 Motorised Clemen Unit: The sample is

clamped to a fixed platform. At the press of a button, the tool is

moved across the sample and stops automatically at the end of

its travel. Contact between the tool and a metallic sample is

indicated by a lamp and voltmeter.

1.1 MANUAL CLEMEN UNIT

1 Weight

2 Clamp

3 Load Beam

4 Tool

5 Sample Platform

1 Weight

2 Support for additional 1kg

(2.2lb) weights

3 Load Beam

4 Clamp

5 Voltmeter

6 Start Button

7 Power On/Off Button

8 Sample Platform

9 Tool

1 OVERVIEW (continued)

www.elcometer.com

en-3



Elcometer 3000 Clemen Unit



Tungsten Carbide Ball Tool; 1mm (0.04")



Calibration Certificate - if ordered



User Guide

Additional items supplied with the Elcometer 3000 Motorised

Clemen Unit



1kg Weight (x4)



Mains Leads: UK, EUR & US

The Elcometer 3000 Clemen Unit is packed in a plywood and / or heavy duty cardboard and foam

package. It is recommended that this packaging is retained and reused in the event that the

instrument needs to be transported. If the packaging is disposed of, please ensure that this is done in

an environmentally sensitive manner. Consult your local Environmental Authority for further guidance.

2 BOX CONTENTS

1.2 MOTORISED CLEMEN UNIT

3 WORKING SAFELY

To reduce the risk of electric shock, do not open the housing of

the Elcometer 3000 Motorised Clemen Unit. There are no

user-servicable parts inside. The warranty will be invalidated if

the instrument has been opened.

To reduce the risk of fire or electric shock, do not expose the

Elcometer 3000 Motorised Clemen Unit to rain or excess

moisture.

3 WORKING SAFELY (continued)

4.1 INSTALLATION

The Elcometer 3000 Motorised Clemen Unit is heavy; manual

lifting of the tester must be carried out by at least two people.

Place the Elcometer 3000 on a flat level surface suitable for the load

imposed by the tester. The Elcometer 3000 Motorised Clemen Unit

has adjustable feet which can be used to level the tester.

4.2 SWITCHING ON / OFF - MOTORISED CLEMEN UNIT ONLY

Press the On/Off button to switch the unit on. The button will

illuminate when the unit is switched on. Press the On/Off button again

to switch the unit off.

The IEC inlet is protected by one fuse - see Section 10 ‘Technical

Specification’ on page en-10 for fuse rating.

The UK mains plug is fitted with a fuse. When replacing this fuse,

ensure a fuse of the correct rating is used - see Section 10 ‘Technical

Specification’ on page en-10 for details.

Elcometer recommends using mains leads approved by a recognised

testing authority. Examples of suitable mains leads are UK, EUR

H05RN-F 3G 0.75mm 2 cable, US SJT 18AWG/3C cable.

4 GETTING STARTED

5 TESTING A SAMPLE - MANUAL CLEMEN UNIT

Before a sample can be tested, the height of the tool must be adjusted.

5.1 ADJUSTING THE TOOL HEIGHT

1 Place the sample onto the sample platform and fix into position by

rotating the clamp handle.

2 Lift and hold the load beam in its raised position and slide the

sample platform until the centre of the sample is underneath the

tool.

www.elcometer.com en-4

5 TESTING A SAMPLE - MANUAL CLEMEN UNIT (continued)

3 Insert the metal shim (a) between the nylon wheel (b) and the

load beam (c) and then lower the load beam.

4 Adjust the height of the tool (d) until it is touching the surface of

the sample then tighten the knurled wheel (e), turning clockwise,

to lock the tool into position.

5 Raise the load beam, remove the metal shim and slide the

sample platform back to its starting position.

6 Slide the weight along the load beam to the required load and

lock in place by tightening the knurled wheel. The load can be

set from 0 to 2kg (0 to 4.4lb).

The instrument and sample are now ready for the test to be carried

out.

5.2 TEST PROCEDURE

1 Pull the sample platform towards you in a single smooth action;

the standard speed of movement is approximately 30mm/s

(1.2"/s).

2 The tool will lower down onto the sample at the start of the test

and raise up at the end of the test.

3 Inspect the sample for damage in accordance with the

requirements of the test standard. Repeat the test as necessary,

increase the loading between test.

(a)

(b)

(c )

(d)

(e)

www.elcometer.com

en-5

6 TESTING A SAMPLE - MOTORISED CLEMEN UNIT

Before a sample can be tested, the height of the tool must be adjusted.

6.1 ADJUSTING THE TOOL HEIGHT

1 Connect the unit to the mains power supply and press the Power

On/Off button to switch on the instrument.

2 Place the sample onto the sample platform and fix in position by

rotating the clamp handle.

3 Adjust the height of the tool to its upper position to clear the

sample.

4 With the tool positioned at either end, press the Start button then

immediately press the Power On/Off button. This will stop the

load beam near the centre.

5 Insert the metal shim (a) between the nylon wheel (b) and the

load beam (c) and then lower the load beam.

6 Adjust the height of the tool (d) until it is touching the surface of

the sample then tighten the knurled wheel (e), turning clockwise,

to lock the tool into position.

(a)

(b)

(c )

(d)

(e)

7 Raise the load beam, remove the metal shim and whilst

supporting the load beam, press the Power On/Off button

followed by the Start button to return the tool to its starting

position.

 Supporting the load beam whilst the tool is moving to its starting position

prevents damage to the sample surface, the tool or the sample platform.

8 Slide the weight along the load beam to the required load and

lock in place by tightening the knurled wheel. The load can be

set from 0 to 1.5kg (0 to 3.3lb) using the sliding weight.

www.elcometer.com en-6

6 TESTING A SAMPLE - MOTORISED CLEMEN UNIT (continued)

For loads between 1.5 and 5kg (3.3 and 11lb) use the additional 1kg

(2.2lb) supplied. Place the required number of weights on the vertical

rod on the load beam to obtain the correct load. For example, if a load

of 3.5kg (7.7lb) is required, place three of the 1kg (2.2lb) weights on to

the vertical rod and slide the weight to the 0.5kg (1.1lb) mark on the

scale.

The instrument and sample are now ready for the test to be carried

out.

6.2 TEST PROCEDURE

Keep fingers clear of the mechanism during use.

1 Press the Start button. The tool will start to move and will lower

down onto the sample at the start of the test, raise up at the end

of the test and then stop automatically.

2 Inspect the sample for damage in accordance with the

requirements of the test standard. Repeat the test as necessary,

increase the loading between test.

The complete destruction of a paint film on a metallic sample is

observed when the voltmeter needle indicates 10 V to 12 V and when

the Start button flashes (the electrical detection device operates only

on metallic samples which are uncoated on the reverse side).

6.3 TESTING THICK SAMPLES

The Elcometer 3000 Motorised Clemen Unit as supplied can be used

to test samples with a maximum thickness of 3mm (0.12"). An

Adjustment Kit is available to purchase as an optional accessory which

allows testing of samples up to 20mm (0.8") thick.

The Adjustment Kit consists of the items listed below. Refer to Figure 1

on page en-8 for the location of the parts.

Part

Description

Qty

Load Beam Spacer; 55 x 39 x 5mm

Sample Clamp Spacer; 35 x 30 x 12mm

Height Gauge for Wheel; 5 & 15mm

Height Gauge for Wheel; 10 & 20mm

www.elcometer.com

en-7

6 TESTING A SAMPLE - MOTORISED CLEMEN UNIT (continued)

Part

Description

Qty

Hexagonal Wrench; 3mm

M4 x 20 Screw for Load Beam

4 sets

M4 x 25 Screw for Sample Clamp

2 sets

Height Adjustable Wheel

A + E

G + C

B + F

Fit the parts in accordance with the recommendations given in the

table below.

Sample Thickness

5mm Spacers for

Load Beam Base (Qty)

12mm Spacer for

Sample Clamp

Height Gauge

for Wheel

inches

0.5 - 5

0.02 - 0.2

Not Required

5mm

5 - 10

0.2 - 0.4

Not Required

10mm

10 - 15

0.4 - 0.6

Required

15mm

15 - 20

0.6 - 0.8

Required

20mm

Note:

1) Fit the load beam base and sample clamp to the spacers using screws of an appropriate length

(Parts E & F above).

2) Use the height gauge (Part C above) to adjust the height of the nylon wheel and then tighten the

knurled wheel to lock in place.

www.elcometer.com en-8

7.1 BALL TOOL

Each Elcometer 3000 is supplied with a 1mm (0.04") tungsten carbide

ball tool as standard.

Due to the nature of the test, the ball tool will wear with use. Spare /

replacement tools are available to purchase from Elcometer or your

local Elcometer supplier.

Description Part Number

Tungsten Carbide Ball Tool; 1mm (0.04") KT003000P021

7.2 CUTTING TOOL FOR SCRATCH TESTING

Available to purchase as an optional accessory, the cutting tool gives a

much more aggressive scratch than the standard ball tool supplied

with each instrument. When using the cutting tool, follow the same

adjustment procedure and test procedure as given for the standard ball

tool.

Description Part Number

Tungsten Carbide Cutting Tool; 2mm (0.08") KT003000N001

7.3 ADJUSTMENT KIT

Available to purchase as an optional accessory for the Elcometer 3000

Motorised Clemen Unit, the adjustment kit allows testing of samples up

to 20mm (0.8") thick - see Section 6.3 ‘Testing Thick Samples’ on page

en-7 for further details.

Description Part Number

Adjustment Kit from 5 - 20mm/0.02 - 0.8" KT003000N015

www.elcometer.com

en-9

7 SPARES & ACCESSORIES

8 CARE & MAINTENANCE

The top of the instrument around the test sample area should be

regularly wiped clean using a dry cloth.

The Elcometer 3000 does not contain any user-serviceable

components. In the unlikely event of a fault, the instrument should be

returned to your local Elcometer supplier or directly to Elcometer.

The warranty will be invalidated if the instrument has been opened.

Andere Handbücher für 3000 Series

Inhaltsverzeichnis

Andere Elcometer Messgerät Handbücher

Elcometer

Elcometer protovale P330 Bedienungsanleitung

Elcometer

Elcometer 456 Bedienungsanleitung

Elcometer

Elcometer SCM400 Bedienungsanleitung

Elcometer

Elcometer 331 Series Bedienungsanleitung

Elcometer

Elcometer 456 IPC Bedienungsanleitung

Elcometer

Elcometer PTG6 Bedienungsanleitung

Elcometer

Elcometer 456 IPC Bedienungsanleitung

Elcometer

Elcometer 224 Bedienungsanleitung

Elcometer

Elcometer 112 Bedienungsanleitung

Elcometer

Elcometer 224 Bedienungsanleitung

Elcometer

Elcometer SAGOLA Classic S1 Bedienungsanleitung

Elcometer

Elcometer 204 Bedienungsanleitung

Elcometer

Elcometer CG20 Bedienungsanleitung

Elcometer

Elcometer PG70 Bedienungsanleitung

Elcometer

Elcometer 406L Bedienungsanleitung

Elcometer

Elcometer 2080 Bedienungsanleitung

Elcometer

Elcometer 106 Bedienungsanleitung

Elcometer

Elcometer FD700DL+ Bedienungsanleitung

Elcometer

Elcometer 345 Bedienungsanleitung

Elcometer

Elcometer 456 3 Bedienungsanleitung

Elcometer

Elcometer CG30 Bedienungsanleitung

Elcometer

Elcometer 415 Bedienungsanleitung

Elcometer

Elcometer 331 H Bedienungsanleitung

Elcometer

Elcometer 355 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung