Eldes ESIM364 Bedienungsanleitung

ESIM364

GSM ALARM AND MANAGEMENT SYSTEM

INSTALLATION MANUAL

COMPLIES WITH EN 501311 GRADE 3, CLASS II REQUIREMENTS

EN ESIM364 INSTALLATION MANUAL v1.9

Installation Manual v1.9

Valid for ESIM364 v02.13.00 and up

Safety instructions

Please read and follow these safety guidelines in order to maintain safety of operators and people around:

• GSM alarm & management system ESIM364 (also referenced as “alarm system”, “system” or “device”) has radio transceiver operating in

GSM 850/900/1800/1900 bands.

• DO NOT use the system where it can be interfere with other devices and cause any potential danger.

• DO NOT use the system with medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.

• DO NOT attempt to personally repair the system.

• System label is on the bottom side of the device.

GSM alarm system ESIM364 is a device mounted in limited access areas. Any system repairs must be done only by qualied,

safety aware personnel.

The system must be powered by main 16-24V ~50/60 Hz1.5A max or 18-24V 1,5A max power supply which must be

approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the

system, switching the pole terminals places does not have any aect.

Any additional devices linked to the system ESIM364 (computer, sensors, relays etc.) must be approved by LST EN 60950-1

standard.

The power supply can be connected to AC mains only inside installation room with auto-

matic 2-pole circuit breaker capable of disconnecting circuit in the event of short circuit

or over-current condition. Open circuit breaker must have a gap between connections

of more than 3mm (0.12in) and the disconnection current 5A.

Phase

AC 230V

50/60Hz/DC 24V

USB cable

Null

ESIM364

AC/DC

Mains power and backup battery must be disconnected before any installation or tuning work starts. The system installation

or maintenance must not be done during stormy conditions

Backup battery must be connected via the connection which in the case of breaking would result in disconnection of one of

battery pole terminals. Special care must be taken when connecting positive and negative battery terminals. Switching the

pole terminals places is NOT allowed.

In order to avoid re or explosion hazards the system must be used only with approved backup battery.

The device is fully turned o by disconnecting 2-pole switch o device of the main power supply and disconnecting backup

battery connector.

Fuse F1 type – Slow Blown 3A. Replacement fuses have to be exactly the same as indicated by the manufacturer.

If you use I security class computer for setting the parameters it must be connected to earth.

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that the

product must not be disposed of together with household waste. To prevent possible harm to human health and/or the envi-

ronment, the product must be disposed on in an approved and environmentally safe recycling process. For further information

on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste disposal

in your area.

ESIM364 INSTALLATION MANUAL v1.9

Contents

1. GENERAL INFORMATION.........................................................................................................................................................6

1.1. Functionality......................................................................................................................................................................................................6

1.2. Compatible Device Overview...........................................................................................................................................................................6

1.3. Default Parameters and Ways of Parameter Conguration .......................................................................................................................6

2. Technical Specications .......................................................................................................................................................14

2.1. Electrical and Mechanical Characteristics ..................................................................................................................................................14

2.2. Main Unit, LED Indicator and Connector Functionality .............................................................................................................................15

2.3. Wiring Diagrams ..............................................................................................................................................................................................16

3. INSTALLATION .......................................................................................................................................................................22

4. GENERAL OPERATIONAL DESCRIPTION............................................................................................................................... 26

5. CONFIGURATION METHODS ..................................................................................................................................................27

5.1. SMS Text Messages.........................................................................................................................................................................................27

5.2. EKB2 LCD Keypad.............................................................................................................................................................................................27

5.3. EKB3/EKB3W LED Keypad ............................................................................................................................................................................ 28

5.4. ELDES Conguration Tool Software............................................................................................................................................................ 28

6. SMS PASSWORD AND INSTALLER CODE ............................................................................................................................... 30

7. SYSTEM LANGUAGE ...............................................................................................................................................................32

8. USER PHONE NUMBERS ........................................................................................................................................................33

8.1. User Phone Number Names ......................................................................................................................................................................... 34

8.2. System Control from any Phone Number................................................................................................................................................... 34

9. DATE AND TIME......................................................................................................................................................................35

9.1. Automatic Date and Time Synchronization ................................................................................................................................................35

10. MASTER AND USER CODES ...................................................................................................................................................37

10.1. Master and User Code Names ...................................................................................................................................................................... 39

11. IBUTTON KEYS ...................................................................................................................................................................... 40

11.1. Adding and Removing iButton Keys............................................................................................................................................................ 40

11.2. iButton Key Names......................................................................................................................................................................................... 41

12. ARMING AND DISARMING..................................................................................................................................................... 42

12.1. Free of Charge Phone Call............................................................................................................................................................................. 43

12.2. SMS Text Message.......................................................................................................................................................................................... 43

12.3. EKB2 Keypad and User/Master Code .......................................................................................................................................................... 44

12.4. EKB3 Keypad and User/Master Code .......................................................................................................................................................... 46

12.5. EKB3W Keypad and User/Master Code....................................................................................................................................................... 48

12.6. iButton Key...................................................................................................................................................................................................... 50

12.7. EWK1/EWK2 Wireless Keyfob .......................................................................................................................................................................51

12.8. Arm-Disarm by Zone.......................................................................................................................................................................................52

12.9. Disabling and Enabling Arm/Disarm Notications.....................................................................................................................................52

13. EXIT AND ENTRY DELAY ....................................................................................................................................................... 54

14. ZONES.....................................................................................................................................................................................56

14.1. Zone Numbering............................................................................................................................................................................................. 56

14.2. Zone Expansion .............................................................................................................................................................................................. 56

14.3. 6-Zone Mode................................................................................................................................................................................................... 56

14.4. ATZ (Advanced Technology Zone) Mode.....................................................................................................................................................57

14.5. Zone Type Denitions ................................................................................................................................................................................... 58

14.6. Zone Attributes .............................................................................................................................................................................................. 58

14.7. Bypassing and Activating Zones.................................................................................................................................................................. 62

14.8. Zone Names .................................................................................................................................................................................................... 62

14.9. Disabling and Enabling Zones ..................................................................................................................................................................... 63

14.10 Viewing Zone State ....................................................................................................................................................................................... 64

15. STAY MODE.............................................................................................................................................................................65

16. TAMPERS............................................................................................................................................................................... 66

16.1. Tamper Names................................................................................................................................................................................................ 67

17. ALARM INDICATIONS AND NOTIFICATIONS FOR USER ....................................................................................................... 68

17.1. Enabling and Disabling Alarm Notications............................................................................................................................................... 70

17.2. Audio Files and Introduction Audio..............................................................................................................................................................71

18. PROGRAMMABLE (PGM) OUTPUTS.......................................................................................................................................72

18.1. PGM Output Numbering .................................................................................................................................................................................72

18.2. PGM Output Expansion...................................................................................................................................................................................72

18.3. PGM Output Names.........................................................................................................................................................................................73

18.4. Enabling and Disabling PGM Outputs...........................................................................................................................................................73

18.5. Turning PGM Outputs ON and OFF................................................................................................................................................................73

18.6. PGM Output Control by Event and Scheduler .............................................................................................................................................75

18.7. Wireless PGM Output Type Denitions....................................................................................................................................................... 76

19. WIRELESS DEVICES................................................................................................................................................................77

19.1. Pairing, Removing and Replacing Wireless Device ................................................................................................................................... 78

19.2. Wireless Device Information......................................................................................................................................................................... 79

EN ESIM364 INSTALLATION MANUAL v1.9

19.3. Wireless Signal Status Monitoring .............................................................................................................................................................. 79

19.4. Disabling and Enabling Siren if Wireless Signal is Lost............................................................................................................................ 81

19.5. EKB3W - Wireless LED Keypad..................................................................................................................................................................... 81

19.6. EWR2 – Wireless Signal Repeater................................................................................................................................................................ 83

19.7. EWF1/EWF1CO - Wireless Smoke/CO Detector ........................................................................................................................................ 84

19.8. EW2 - Wireless Zone and PGM Output Expansion Module ...................................................................................................................... 86

19.9. EWM1 - Wireless Power Socket.................................................................................................................................................................... 86

20. WIRED SIREN/BELL............................................................................................................................................................... 88

20.1. BELL Output Status Monitoring................................................................................................................................................................... 89

20.2. Bell Squawk..................................................................................................................................................................................................... 89

20.3. Bell Squawk in Stay Mode ............................................................................................................................................................................. 90

20.4. Indication by EWS2 - Wireless Outdoor Siren Indicators ..........................................................................................................................91

20.5. Indication by EWS3 - Wireless Indoor Siren Indicators ............................................................................................................................ 92

21. BACKUP BATTERY, MAINS POWER STATUS MONITORING AND MEMORY........................................................................... 93

21.1. Backup Battery Status Monitoring .............................................................................................................................................................. 93

21.2. Mains Power Status Monitoring................................................................................................................................................................... 95

22. GSM CONNECTION AND ANTENNA STATUS MONITORING....................................................................................................97

22.1. GSM Connection Status Monitoring ............................................................................................................................................................ 97

22.2. GSM Antenna Status Monitoring ................................................................................................................................................................. 98

23. PARTITIONS .......................................................................................................................................................................... 99

23.1. Zone Partition ................................................................................................................................................................................................. 99

23.2. User Phone Number Partition...................................................................................................................................................................... 99

23.3. Keypad Partition and Keypad Partition Switch........................................................................................................................................100

23.4. User/Master Code Partition ...................................................................................................................................................................... 101

23.5. iButton Key Partition ................................................................................................................................................................................... 102

23.6. EWK1/EWK2/EWK2A Wireless Keyfob Partition .................................................................................................................................... 102

24. TEMPERATURE SENSORS................................................................................................................................................... 103

24.1. Adding, Removing and Replacing On-Board Temperature Sensors .................................................................................................... 103

24.2. Primary and Secondary Temperature Sensors........................................................................................................................................104

24.3. Setting Up MIN and MAX Temperature Thresholds. Temperature Info SMS...................................................................................... 105

24.4. Temperature Sensor Names....................................................................................................................................................................... 106

25. REMOTE LISTENING AND 2-WAY VOICE COMMUNICATION................................................................................................ 107

26. SYSTEM INFORMATION. INFO SMS..................................................................................................................................... 108

26.1. Periodic Info SMS..........................................................................................................................................................................................108

27. SYSTEM NOTIFICATIONS .....................................................................................................................................................110

27.1. SMS Text Message Delivery Restrictions ................................................................................................................................................. 120

27.2. SMSC (Short Message Service Center) Phone Number .......................................................................................................................... 120

28. EVENT AND ALARM LOG ......................................................................................................................................................121

28.1. Event Log ........................................................................................................................................................................................................121

28.2. Alarm Log....................................................................................................................................................................................................... 122

29. INDICATION OF SYSTEM FAULTS .........................................................................................................................................123

30. MONITORING STATION.........................................................................................................................................................125

30.1. Data Messages – Events.............................................................................................................................................................................. 126

30.2. Communication............................................................................................................................................................................................. 132

30.3. SIA IP Protocol Settings .............................................................................................................................................................................. 144

31. DUAL SIM MANAGEMENT ................................................................................................................................................... 144

31.1. Disabled Mode............................................................................................................................................................................................... 144

31.2. Automatic Mode ........................................................................................................................................................................................... 144

31.3. Manual Mode................................................................................................................................................................................................. 144

32. WIRED DEVICES................................................................................................................................................................... 146

32.1. RS485 Interface ........................................................................................................................................................................................... 146

32.2. 1-Wire Interface............................................................................................................................................................................................ 155

32.3. Modules Interface ........................................................................................................................................................................................ 155

33. SERVICE MODE .................................................................................................................................................................... 158

34. REMOTE SYSTEM RESTART ................................................................................................................................................ 158

35. EN 50131-1 GRADE 3............................................................................................................................................................159

36. ELDES CLOUD SERVICES ..................................................................................................................................................... 160

37. TECHNICAL SUPPORT .........................................................................................................................................................161

37.1. Troubleshooting ........................................................................................................................................................................................... 161

37.2. Restoring Default Parameters ................................................................................................................................................................... 161

37.3. Updating the Firmware via USB Cable Locally........................................................................................................................................ 161

37.4. Updating Firmware via GPRS Connection Remotely .............................................................................................................................. 162

37.5. Frequently Asked Questions...................................................................................................................................................................... 162

38. RELATED PRODUCTS........................................................................................................................................................... 164

39. GLOSSARY – APPENDIX 1.....................................................................................................................................................167

40. EKB3/EKB3W COMMANDS - APPENDIX 2 .......................................................................................................................... 169

41. SMS COMMANDS - APPENDIX 3 ......................................................................................................................................... 180

ESIM364 INSTALLATION MANUAL v1.9

Technical Support

If you experience diculty during the installation or subsequent use of a ELDES UAB system, you may contact ELDES UAB distributor or dealer

in your country/region.

Warranty Procedures

To obtain warranty service, you may return a defective system to your original point of purchase, or the authorized ELDES UAB dealer or dis-

tributor from whom you purchased the ELDES product.

Limited Liability

The buyer must agree that the system will reduce the risk of re, theft, burglary or other dangers but does not guarantee against such events.

ELDES UAB will not take any responsibility regarding personal or property or revenue loss while using the system. ELDES UAB liability accord-

ing to local laws does not exceed value of the purchased system. ELDES UAB is not aliated with any of the Internet providers therefore is not

responsible for the quality of Internet service.

Manufacturer Warranty

ELDES UAB warrants this system only to the original purchaser and only in case of defective workmanship and materials under normal use of the sys-

tem for a period of twenty four (24) months from the date of shipment by the ELDES UAB. Warranty obligations do not cover expandable materials

(components, which require periodic replacement with the operation of system - power elements (batteries)), holders and enclosures. The warranty

remains valid only if the system is used as intended, following all guidelines outlined in this manual and in accordance with the operating conditions

specied. The warranty is void if the system has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous en-

vironments or force majeure factors.

Content of Pack

Item Quantity

1. ESIM364............... ..............................................1

2. Microphone........................................................1

3. SMA antenna......... ............................................2

4. Buzzer........................... ......................................1

5. Back-up battery connection wire... ...............1

6. User manual.......................................................1

7. Resistors 5,6k......................... ........................12

8. Resistors 3,3k.................................................6

9. Plastic standos................ ...............................4

About Installation Manual

This document describes detailed installation and operation process of alarm system ESIM364. It is very important to read the installation

manual before starting to use the system.

It is not allowed to copy and distribute information in this document or pass to a third party without advanced written

authorization by ELDES UAB. ELDES UAB reserves the right to update or modify this document and/or related products

without a warning. Hereby, ELDES UAB declares that this GSM alarm and management system ESIM364 is in compli-

ance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of con-

formity may be consulted at eldesalarms.com

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

15.105 statement (for digital devices)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must

not be located or operating in conjunction with any other antenna or transmitter.

EN ESIM364 INSTALLATION MANUAL v1.9

1. GENERAL INFORMATION

1.1. Functionality

ESIM364 – micro-controller based alarm system for houses, cottages, country homes, garages and other buildings, also capable of manag-

ing electrical appliances via cellular GSM/GPRS network. It can also be used as Intercom system.

Examples of using the system:

• Property security.

• Alarm switch.

• Thermostat, heating and air-conditioner control, temperature monitoring.

• Lighting, garden watering, water pump and other electrical equipment control via SMS text messages.

• Remote listening to what is happening in the secured area.

• Mains power status notication by SMS text message.

• Two-way intercom device via GSM network.

1.2. Compatible Device Overview

Wired Devices

Device Description Max. Connectible Devices

EKB2 LCD keypad 4*

EKB3 LED keypad 4*

EA1 Audio output module with 3,5mm jack 1**

EA2 Audio amplier module 1W 8 1**

EPGM1 16 zone and 2 PGM output expansion module 2

ELAN3-ALARM Ethernet communicator 1

EPGM8 8 PGM output expansion module 1**

Wireless Devices

Device Description Max. Connectible Devices

EW2 Wireless 2 zone and 2 PGM output expansion module 16*****

EWP2 Wireless motion detector 32***

EWD2 Wireless magnetic door contact/shock sensor/ood sensor 32***

EWK1**** Wireless keyfob with 4 buttons 5***

EWK2**** Wireless keyfob with 4 buttons 5***

EWS3 Wireless indoor siren 32***

EWK2A**** Wireless keyfob with 1 button 5***

EWS2 Wireless outdoor siren 32***

EKB3W Wireless LED keypad 4***

EWF1 Wireless smoke detector 32***

EWF1CO Wireless smoke and CO detector 32***

EWR2 Wireless signal repeater 4***

EWM1 Wireless power socket 32***

* - A mixed combination of EKB2 and EKB3 keypads is supported. The combination can consist of up to 4 keypads in total.

** - Only 1 of these modules can be connected at a time if the module slots are implemented in ESIM364 unit.

*** - A mixed combination of wireless devices is supported. The combination can consist of up to 32 wireless devices in total.

**** - A mixed combination of EWK1, EWK2 and EWK2A keyfobs is supported. The combination can consist of up to 5 keyfobs in total.

***** - EW2 creates 4 wireless zones, therefore the max. number of connectible EW2 devices is 16 if no keypad zones, no EPGM1 and no

virtual zones exist in the system’s conguration.

1.3. Default Parameters and Ways of Parameter Conguration

Main Settings

Parameter Default Value

Congurable by:

SMS EKB2 EKB3/

EKB3W

Conguration

Tool

User 1... 10 name N/A 

User 1... 10 phone number N/A    

User 1... 10 partition Partition 1   

User 1...10 - call in case of alarm Enabled   

Allow control from any phone number Disabled    

SMS password 0000    

SMS language Depends on the rmware

Partition 1 name PART1 

Partition 2 name PART2 

Partition 3 name PART3 

ESIM364 INSTALLATION MANUAL v1.9

Partition 4 name PART4 

Partition 1... 4 exit delay 15 seconds    

GSM signal loss indication - delay 180 seconds 

GSM signal loss indication – activate output N/A 

Dual SIM management – SIM card switch Disabled 

Dual SIM management – try to nd operator for a

maximum of 3 time (s) 

Dual SIM management – send SMS/call via Currently in use SIM 

Main Settings

Parameter Default Value

Congurable by:

SMS EKB2 EKB3/

EKB3W

Conguration

Tool

Passwords/Codes

Installer's code 1470   

Duress code N/A   

SGS code N/A   

Passwords/codes format 4-digit 

Prompt additionally for master code when cong-

uring via keypad/software Disabled 

Master code 1111   

Master code name N/A 

Master code partition Partition 1, Partition 2, Partition 3, Parti-

tion 4   

User code 2... 30 N/A   

User code 2... 30 name N/A 

User code 2... 30 partition Partition 1   

Faults

Main power loss Enabled 

Low battery Enabled 

Battery dead or missing Enabled 

Battery failed Enabled 

Wired siren failed Enabled 

RF jammer detected Enabled 

Tamper alarm Enabled 

Date/time not set Enabled 

GSM connection failed Enabled 

GSM antenna failed Enabled 

Wireless antenna failed Enabled 

Communication bus failed Enabled 

Critical CO level Enabled 

Wireless power socket fault Enabled 

Wireless device low battery Enabled 

Notications

System armed – User 1... 10 Enabled   

System armed – SMS delivery report Enabled   

System disarmed – User 1... 10 Enabled   

System disarmed – SMS delivery report Enabled   

General alarm – User 1... 10 Enabled   

General alarm – SMS delivery report Enabled   

Main power loss/restore – User 1... 10 Enabled   

Main power loss/restore – SMS delivery report Enabled   

Battery failed – User 1... 10 Enabled   

Battery failed – SMS delivery report Enabled   

Battery dead or missing – User 1... 10 Enabled   

Battery dead or missing – SMS delivery report Enabled   

Low battery – User 1... 10 Enabled   

Low battery – SMS delivery report Enabled   

Siren fail/restore – User 1... 10 Disabled   

Siren fail/restore – SMS delivery report Disabled   

EN ESIM364 INSTALLATION MANUAL v1.9

RF jammer detected – User 1... 10 Disabled   

RF jammer detected – SMS delivery report Disabled   

Date/time not set – User 1... 10 Disabled   

Date/time not set – SMS delivery report Disabled   

GSM connection failed – User 1... 10 Disabled   

GSM connection failed – SMS delivery report Disabled   

GSM antenna fail/restore – User 1... 10 Disabled   

GSM antenna fail/restore – SMS delivery report Disabled   

Tamper alarm/restore – User 1... 10 Enabled   

Tamper alarm/restore – SMS delivery report Enabled   

Communication bus fail/restore – User 1... 10 Enabled   

Communication bus fail/restore – SMS delivery

report Enabled   

Temperature info – User 1... 10 Enabled   

Temperature info – SMS delivery report Enabled   

System started – User 1... 10 Enabled   

System started – SMS delivery report Enabled   

Periodical info – User 1... 10 Enabled   

Periodical info – SMS delivery report Enabled   

Wireless signal loss – User 1... 10 Enabled   

Wireless signal loss – SMS delivery report Enabled   

Unable to arm – User 1... 10 Enabled   

Unable to arm – SMS delivery report Enabled   

Zone bypass - User 1... 10 Enabled   

Zone bypass – SMS delivery report Enabled   

Critical CO level - User 1... 10 Enabled   

Critical CO level – SMS delivery report Enabled   

Wireless socket signal loss/restore - User 1... 10 Disabled  

Wireless socket signal loss/restore – SMS delivery

report Disabled  

Report/Control zone triggered - User 1... 10 Enabled   

Report/Control zone triggered - SMS delivery

report Enabled   

Incoming SMS forwarding - User 1... 10 Enabled  

Incoming SMS forwarding - SMS delivery report Enabled  

Wireless communication failed - User 1... 10 Disabled   

Wireless communication - SMS delivery report Disabled   

Send to all users simultaneously – all notications Disabled   

Time Synchronization

Time synchronization Disabled 

Phone number of the currently inserted SIM card N/A 

Synchronization frequency 30 days 

Event Log

Event log Enabled    

Zones

Parameter Default Value

Congurable by:

SMS EKB2 EKB3/

EKB3W

Conguration

Tool

On Board

Z1... Z6 zone name Zone1... Zone6  

Z1 type Delay   

Z1... Z6 zone status Enabled    

Z2... Z6 type Instant   

Z1... Z6 delay, ms 800 milliseconds 

Z1... Z6 – Stay Disabled   

Z1... Z6 – Force Disabled   

Z1... Z6 Tamper name Tamper1... Tamper6 

Delay-type zone – entry delay 15 seconds    

Z1... Z6 partition Partition 1   

ESIM364 INSTALLATION MANUAL v1.9

Z1... Z6 – Shared Disabled 

Z1... Z6 – audio track N/A 

Z1... Z6 – alarm count to bypass 0

Cross-Zone/Intelli-Zone N/A 

Conrmation Timeout 20 seconds 

Tamper 1... 6 status Enabled 

Z1... Z6 - zone connection type Type 1 

Delay becomes Instant in STAY mode Disabled 

Chime Enabled   

ATZ mode Disabled   

Arm-disarm by zone No1... No4 N/A   

EPGM1 Module

Zone name Zone X 

Zone status Enabled    

Type Instant   

Delay, ms 800 milliseconds 

Stay Disabled   

Force Disabled   

Tamper name Tamper X 

Delay-type zone – entry delay 15 seconds   

Partition Partition 1   

Shared Disabled 

Audio track N/A 

Alarm count to bypass 0

Cross-Zone/Intelli-Zone N/A 

Conrmation Timeout 20 seconds 

Tamper status Enabled 

Zone connection type for all EPGM1 zones Type 1 

Wireless Devices

Zone name Zone X  

Zone status Enabled    

Type Depends on the connected wireless device

model   

Stay Disabled   

Force Disabled   

Tamper name Tamper X 

Delay-type zone – entry delay 15 seconds   

Partition Partition 1   

Shared Disabled 

Audio track N/A 

Alarm count to bypass 0

Cross-Zone/Intelli-Zone N/A 

Conrmation Timeout 20 seconds 

Tamper status Enabled 

Keypads

Zone name Zone X  

Zone status Disabled    

Type Instant   

Stay Disabled   

Force Disabled   

Tamper name Tamper X 

Delay-type zone – entry delay 15 seconds   

Partition Partition 1   

Shared Disabled 

Audio track N/A 

Alarm count to bypass 0

Cross-Zone/Intelli-Zone N/A 

Conrmation Timeout 20 seconds 

Tamper status Enabled 

Virtual Zones

EN ESIM364 INSTALLATION MANUAL v1.9

Zone name Zone X 

Zone status Disabled  

Type Instant  

Force Disabled  

Delay-type zone – entry delay 15 seconds  

Partition Partition 1  

Shared Disabled 

Alarm count to bypass 0

Cross-Zone/Intelli-Zone N/A 

Conrmation Timeout 20 seconds 

Tamper status Enabled 

PGM Outputs

Parameter Default Value

Congurable by:

SMS EKB2 EKB3/

EKB3W

Conguration

Tool

On Board

C1... C4 output name Controll1... Controll4  

C1... C4 output state OFF    

C1... C4 output status Enabled 

Using module EPGM8 Disabled   

EPGM1 Module

Output name ControllX  

State OFF    

Status Disabled 

Wireless Devices

Output name ControllX  

Type Depends on the connected wireless de-

vice model 

State OFF    

Status Disabled 

MS Settings

Parameter Default Value

Congurable by:

SMS EKB2 EKB3/

EKB3W

Conguration

Tool

Management

MS mode Disabled    

Main Account 9999   

GSM and SMS – attempts 5  

GSM and SMS – tel. number 1... 3 N/A   

PSTN – treat PSTN call as user call Disable 

PSTN – attempts 5  

PSTN – tel. number 1... 3 N/A   

CSD – attempts 5  

CSD – tel. number 1... 5 N/A   

Parallel data transfer via IP network Disabled   

IP Server 1... 3 – IP attempts 3  

IP Server 1... 3 – test period 180 seconds   

IP Server 1... 3 – protocol UDP    

IP Server 1...3 – account 9999   

IP Server 1...3 – unit ID 0000   

IP Server 1... 3 – communication protocol EGR100   

IP Server 1... 3 – server IP 0.0.0.0    

IP Server 1... 3 – server port 20000    

IP Server 1... 3 – encryption key - status Disabled 

IP Server 1... 3 – encryption key 0000 

Communication - primary IP Server 1 (GPRS)   

Communication – backup 1... 5 N/A   

Delay after last communication attempt 600 seconds   

SIA IP protocol settings - encryption Disabled 

SIA IP protocol settings – encryption key 0000 

SIA IP protocol settings – account prex N/A 

Andere Handbücher für ESIM364

Inhaltsverzeichnis

Andere Eldes Sicherheitssystem Handbücher

Eldes

Eldes ESIM364 Bedienungsanleitung

Eldes

Eldes Fumerex Bedienungsanleitung

Eldes

Eldes ESIM264 Bedienungsanleitung

Eldes

Eldes EWS3 Bedienungsanleitung

Eldes

Eldes ESIM264 Bedienungsanleitung

Eldes

Eldes EPIR Bedienungsanleitung

Eldes

Eldes ESIM364 Bedienungsanleitung

Eldes

Eldes ESIM264 Bedienungsanleitung

Eldes

Eldes EPIR Bedienungsanleitung

Eldes

Eldes ESIM264 Bedienungsanleitung

Eldes

Eldes EWS1 Bedienungsanleitung

Eldes

Eldes ESIM264 Bedienungsanleitung

Eldes

Eldes EWK2 Bedienungsanleitung

Eldes

Eldes EWS4 Bedienungsanleitung

Eldes

Eldes ESIM264 Bedienungsanleitung

Eldes

Eldes ESIM262 Bedienungsanleitung

Eldes

Eldes ME1 Bedienungsanleitung

Eldes

Eldes ESIM264 Bedienungsanleitung

Eldes

Eldes ESIM364 Bedienungsanleitung

Eldes

Eldes PITBULL ALARM Bedienungsanleitung

Eldes

Eldes EPIR2 Bedienungsanleitung

Eldes

Eldes EKB3 Bedienungsanleitung

Eldes

Eldes PITBULL ALARM PRO Bedienungsanleitung

Eldes

Eldes PITBULL ALARM PRO Handbuch

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung