ElectrIQ A1/CMAC10M Bedienungsanleitung

USER MANUAL

electriQ 9,200 BTU PORTABLE INDUSTRIAL

AIR CONDITIONER

CMAC10M

Thank you for choosing electriQ

Please read this user manual before using this innovative Air Conditioner and keep it

safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

CONTENTS

SAFETY INFORMATION

FEATURES

APPLIANCE DIAGRAM

INSTALLATION

OPERATION

EMPTYING THE INTERNAL WATER TANK

CLEANING AND MAINTENANCE

TROUBLESHOOTING

SUPPORT

TECHNICAL SPECIFICATION

SAFETY INSTRUCTIONS

Important!

•Carefully read the instructions before operating the unit

•This appliance is for indoor use only.

•Rating: This unit must be only connected to a 220-240 V / 50 Hz

earthed outlet.

•Installation must be in accordance with regulations of the country where the unit is used.

•If you are in any doubt about the suitability of your electrical supply have it checked and,

if necessary, modified by a qualified electrician.

•This air conditioner has been tested and is safe to use. However, as with any electrical

appliance - use it with care.

•Disconnect the power from the appliance before dismantling, assembling or cleaning.

•Avoid touching any moving parts of the appliance.

•Never insert fingers, pencils or any other objects though the guard.

•This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities. It is also not intended for use by those with a

lack of experience and knowledge, unless they have been given supervision or instruction

concerning the use of the appliance by a person responsible for their safety.

•Do not leave children unsupervised with this appliance.

•Do not clean the unit by spraying it or immersing it in water.

•Never connect the unit to an electrical outlet using an extension cord. If an outlet is not

available, one should be installed by a qualified electrician.

•Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not

stretched or exposed to sharp objects/edges.

•A damaged supply cord should be replaced by the manufacturer or a qualified electrician

in order to avoid a hazard.

•Any service other than regular cleaning or filter replacement should be performed by an

authorised service representative. Failure to comply could result in a voided warranty.

•Do not use the appliance for any purpose other than its intended use.

•The air conditioner unit must always be stored and transported upright, otherwise

irreparable damage may be caused to the compressor; if in doubt we suggest waiting at

least 24 hours before starting the unit.

•Do not move the air conditioner while it is operating. When operating the castors should

be locked in position.

•Ensure the unit is positioned so that it is on a flat level surface, and does not cause an

obstruction to walkways.

•This air conditioner is not designed to be used on boats, or any other type of

transportation.

•Avoid restarting the air conditioning unit unless 3 minutes have passed since being

turned off. This prevents damage to the compressor.

•Never use the mains plug as a switch to start and turn off the air conditioning unit. Use

the provided ON/OFF switch located on the control panel.

•Always place the unit on a dry and stable surface.

•The appliance should not be installed in laundry or wet rooms.

•The appliance must be placed in a room without sources of ignition (for example: open

flames, an operating gas appliance or an operating electric heater).

•R290 refrigerant gas complies with European environmental directives.

•R290 has a low GWP (Global Warming Potential) of 3.

•The air conditioners contain around 250 g of R290 refrigerant gas.

•Do not use or store in an unventilated space with an area smaller than 12 m2per unit.

•The room must be such as to prevent stagnation of possible leaks of refrigerant gas as

there could be a danger of fire or explosion should the refrigerant come into contact with

electric heaters, stoves or other sources of ignition.

•Refrigerant gas may be odourless.

•Do not use the product and contact the retailer for advice, if damage has occurred to the

unit which may have compromised the refrigerant system.

•Any repairs or maintenance must only be carried out on the unit by a suitably qualified

engineer. Before opening and servicing the unit the authorised engineer must be in

possession of a copy of the manufacturer’s service manual and must follow the safety

information contained within it to ensure all hazards are minimized.

•The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

•Do not cover or restrict the airflow from the air outlet or inlet.

•For maximum performance the minimum distance from a wall or objects should be

50cm.

•Keep the filters clean. Under normal conditions, filters should only need cleaning once

every three weeks (approximately). Since the filters remove airborne particles, more

frequent cleaning maybe necessary, depending on the air quality.

•For the initial start-up set the fan speed to maximum.

•To protect the unit, we recommend not using the cooling function when the ambient

temperature is higher than 45oC or lower than 18oC.

FEATURES

•The CMAC10M is great for Rooms up to 26 m2.

•2 speed fan: Balancing quiet operation with performance.

•Simple operation.

•Castors for Enhanced Portability.

•Durable metal casing.

HOSE SPECIFICATIONS

Hose

Hose External

Diameter (mm)

Supplied Hose Length

Max Permitted

Hose Length (cm)

Cold Air

120

200

Hot Air

160

300

APPLIANCE DIAGRAM

Hot Air Exhaust

Hose

Cold Air Exhaust

Hose

Control Panel

Removeable Filter

Handle

Water Tank

Castors

INSTALLATION

COLD AIR OUTLETS

1. Line up the dimple on the Elbow with the

notch on the Hose connector on the top of

the air conditioner.

2. Rotate anticlockwise until a click can be

heard, indicating the elbow has locked into

place.

3. Insert the Cold Air Hose into the Elbow,

again lining up the dimple with the notch in

the Elbow.

4. Rotate the pipe anticlockwise to fix it in

place.

5. The pipe can then be extended and pointed

in the desired direction.

HOT AIR OUTLET

1. Push the Hot air pipe onto the Hot air outlet on the top of the

appliance.

2. Extend the pipe and route it outside.

NOTES:

•The best form of installation is through a wall duct. By properly

venting you expel hot air from your room while efficiently

cooling it.

IMPORTANT SAFEGUARDS

If hoses are extended above the permitted length, the unit may

malfunction which can invalidate the warranty. The outlet vent

must be well ventilated and not obstructed as this will cause

the unit to overheat. Keep the all the hoses as straight and

short as possible and avoid bending the air hose by more than

45 degrees in order to maintain the performance of the unit.

Excessive bends in the hose may prevent the unit from

expelling the hot air, which can lead to internal damage which

would invalidate the warranty. Ensure that sufficient space is

left in from the end of the vent pipes (30cm –Cold air, 90cm

Hot air)

OPERATION

Turn the control switch to select your desired fan speed between Low and High.

When you have finished, turn the control switch back to the Off position.

The unit can also be used as a dehumidifier by not using the hot air hose. We advise on setting the unit up

with continuous drainage when using it as a dehumidifier.

MULTI PROTECTIVE FUNCTIONS

FROST PROTECTION

If the temperature of the exhaust is too low, the machine will automatically stop operating until the

temperature has risen.

OVERFLOW PROTECTION

When the water in the internal water tank exceeds the warning level, the machine will stop operating and the

water tank full indicator will illuminate. To resume operation empty the internal water tank. After the water is

emptied, the machine will automatically return to the original state.

AUTO-DEFROST

The machine has automatic defrosting function. If during operation the temperature of the internal coils drops

too low, the unit will enter auto defrost and the heating symbol will flash on the control panel.

AUTOMATIC THERMAL PROTECTION

To protect the service life of the machine, the machine has automatic thermal protection. If the temperature

within the unit is outside of the specified range, the compressor and the lower motor will stop operation. The

appliance will automatically return to normal operation after the temperature of the machine recovers.

COMPRESSOR PROTECTION

To prevent damage to the compressor there is a 3 minute delay start protection function.

EMPTYING THE INTERNAL WATER TANK

MANUAL DRAINAGE:

When the internal water tank is full the unit will stop working.

Shut off the unit and unplug. Try not to move the appliance as this may cause the water in the internal tank to

spill out. Remove the water tank from the base of the unit and empty into a sink or drain. Replace the water

tank in the unit before plugging back in and restarting operation.

CONTINUOUS DRAINAGE:

Remove the water tank from the unit, and remove the rubber cap from the end of the drainage spout. Connect

the drainage pipe to the spout. Feed the drainage pipe through the hole in the side of the unit from the inside

before sliding the water tank back into place. The drain is gravity fed, so can be routed downwards to a suitable

drain. Alternatively the pipe can be attached to an external uplift pump (not supplied) to pump the water

uphill to a suitable drainage point.

NOTE: This model has a self-evaporative function, which reduces the need to empty the water tank. If the unit

is vented correctly most of the water is reused to cool the condenser coils and any excess is evaporated. Please

do not use continuous drainage if you intend to use the self-evaporating facility.

CLEANING AND MAINTENANCE

PLEASE TURN OFF THE UNIT AND UNPLUG FROM THE MAINS BEFORE CLEANING OR PERFORMING ANY

MAINTENANCE

CLEAN THE SURFACE

Clean the surface of the machine with a wet soft cloth. Do not use chemicals, such as benzene, alcohol, gasoline, etc;

otherwise, as this may cause damage to the surface and or the internal workings of the machine

AIR FILTER CLEANING

If the filter screen is clogged with dust, the effectiveness of the air conditioner is reduced. The filter screen should be

cleaned once every two weeks or as often as necessarily in your environment.

END OF SEASON MAINTENANCE

1. Empty the internal water tank.

2. Turn off the unit and pull out the plug.

3. Leave for 24 hours to dry out.

4. Empty the water tank again as a small amount of water may have drained to it..

5. Coil the wire and bind it together, then put it into the accessories space.

6. Separate the vent pipes and store the, safely.

7. Cover the unit and keep it in a dry place.

TROUBLESHOOTING

Do not repair or disassemble the air conditioning. Unqualified repair will invalidate the warranty and may lead to failure, causing

injuries and property damage. Only use it as directed in this user manual and only perform operations advised here.

Problems

Reasons

Solutions

The air

conditioner does

not work.

There is no electricity.

Turn it on after connecting it to a socket with

electricity.

FULL indicator is illuminated

Discharge the water inside.

The ambient temperature is too low or

too high

Only use to use the machine within temperature

range of 18-45⁰C

In cooling mode, the room temperature is

lower than the desired temperature

Change the desired temperature.

In dry mode, the ambient temperature is

low.

The ambient temperature must be above 18 ⁰C.

(60 ⁰F).

The cooling

effect is not good

There is direct sunlight.

Use curtains to reduce the direct sun heat

Doors or windows are open; there are a

lot of people; or in cooling mode, there

are other sources of heat (e.g. fridges)

Close doors and windows; increase air

conditioning power

The filter screen is dirty.

Clean or replace the filter screen.

The air inlet or outlet is blocked.

Clear obstructions; make sure venting is correct as

described in this user manual and hose is not bent

Loud Noise

The air conditioning is not placed on a flat

surface.

Put the air conditioning on a flat and hard place

(to reduce noise).

Compressor does

not work.

Overheat protection starts.

Wait for 3 minutes until the temperature is

lowered, and then restart the machine.

Others

No refrigerant or there is very little

refrigerant

Refer to Service Centre (check leakage, wielding,

vacuum pump, charge refrigerant according to

name plate)

Anti-freezing protection

Waiting for defrosting.

Function will recover automatically. No user input

needed.

High pressure protection

After inside gas pressure comes down, it will

function normally. No user input needed

If problems not listed in the table occur or recommended solutions do not work, please contact the service

centre.

APPENDIX

Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste

must be handled separately as special treatment is necessary. Recycling facilities are now

available for all customers at which you can deposit your old electrical products. Customers

will be able to take any old electrical equipment to participating civic amenity sites run by

their local councils. Please remember that this equipment will be further handled during

the recycling process, so please be considerate when depositing your equipment. Please

contact the local council for details of your local household waste recycling centres.

electriQ UK SUPPORT

www.electriQ.co.uk/support

Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails

to operate call the number below, or complete the online form.

0330 390 3061

1. Has the unit been standing upright for at least 2 hours?

2. Is the unit plugged into the mains?

3. Is the fuse OK?

4. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.

5. Check if the water tank is full.

Office hours: 9AM - 5PM Monday to Friday

www.electriQ.co.uk

Unit J6, Lowfields Business Park

Lowfields Way, Elland

West Yorkshire, HX5 9DA

TECHNICAL DATA

Model

CMAC10M

Cooling capacity:

9,200 BTU

Input power:

950 W

Fan

AC motor with 2 fan speeds.

Air flow volume:

400 m³/h

Input current:

4.2 A

Refrigerant:

R290/250g

Maximum working pressure of

suction/exhaust side:

1.0/2.5 MPa

Maximum Allowable Pressure

2.5 Mpa

Power Supply:

AC 220-240V/50 Hz

Net Weight:

42 kg

Dimension(L*D*H):

430 x 405 x 855 mm

Unit must be vented outside when in Air Cooling mode. For the purposes of EU regulation

EN12102 this is a local air conditioner and produces less than 65dB(A) sound energy.

V20210607

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ElectrIQ Klimaanlage Handbücher

ElectrIQ

ElectrIQ eIQ-9WMINV Betriebsanleitung

ElectrIQ

ElectrIQ SILENT16 Bedienungsanleitung

ElectrIQ

ElectrIQ P12HPW-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ AIRCUBE Bedienungsanleitung

ElectrIQ

ElectrIQ AIRCUBE 10DLX Bedienungsanleitung

ElectrIQ

ElectrIQ P15HP Bedienungsanleitung

ElectrIQ

ElectrIQ SF12000 Bedienungsanleitung

ElectrIQ

ElectrIQ P18HP Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-9WMINV-V2 Betriebsanleitung

ElectrIQ

ElectrIQ ECOSILENT8 Bedienungsanleitung

ElectrIQ

ElectrIQ P16HP Bedienungsanleitung

ElectrIQ

ElectrIQ P12CE-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT8-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ iQool-3MS9K9K9K Betriebsanleitung

ElectrIQ

ElectrIQ AIRFLEX15 Bedienungsanleitung

ElectrIQ

ElectrIQ P15C Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-12K12KC24KWMINV Betriebsanleitung

ElectrIQ

ElectrIQ Slimline ECO AC60E Bedienungsanleitung

ElectrIQ

ElectrIQ CMAC12M Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT10 Bedienungsanleitung

ElectrIQ

ElectrIQ P12HPW Bedienungsanleitung

ElectrIQ

ElectrIQ P12C-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ P12HPWR Bedienungsanleitung

ElectrIQ

ElectrIQ IQOOL-SMART15HP Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung