ElectrIQ P12HPW Bedienungsanleitung

USER MANUAL

electriQ 12,000 BTU PORTABLE AIR CONDITIONER

WITH HEATPUMP AND WIFI

P12HPW

Thank you for choosing electriQ

Please read this user manual before using this innovative Air Conditioner and keep it

safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

CONTENTS

SAFETY INFORMATION

FEATURES

PARTS LIST

INSTALLATION

OPERATION

REMOTE CONTROL

EMPTYING THE INTERNAL WATER TANK

WIFI APP CONTROL

SETTING UP THE APP

CONNECTING THE AIR CONDITIONER

CONTROLLING YOUR DEVICE

SMART SCENES

CLEANING AND MAINTENANCE

TROUBLESHOOTING

ERROR CODES

SUPPORT

TECHNICAL SPECIFICATION

SAFETY INSTRUCTIONS

Important!

•Carefully read the instructions before operating the unit

•This appliance is for indoor use only.

•Rating: This unit must be only connected to a 220-240 V / 50 Hz

earthed outlet.

•Installation must be in accordance with regulations of the country where the unit is used.

•If you are in any doubt about the suitability of your electrical supply have it checked and,

if necessary, modified by a qualified electrician.

•This air conditioner has been tested and is safe to use. However, as with any electrical

appliance - use it with care.

•Disconnect the power from the appliance before dismantling, assembling or cleaning.

•Avoid touching any moving parts of the appliance.

•Never insert fingers, pencils or any other objects though the guard

•This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities. It is also not intended for use by those with a

lack of experience and knowledge, unless they have been given supervision or instruction

concerning the use of the appliance by a person responsible for their safety.

•Do not leave children unsupervised with this appliance.

•Do not clean the unit by spraying it or immersing it in water.

•Never connect the unit to an electrical outlet using an extension cord. If an outlet is not

available, one should be installed by a qualified electrician.

•Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not

stretched or exposed to sharp objects/edges.

•A damaged supply cord should be replaced by the manufacturer or a qualified electrician

in order to avoid a hazard.

•Any service other than regular cleaning or filter replacement should be performed by an

authorised service representative. Failure to comply could result in a voided warranty.

•Do not use the appliance for any purpose other than its intended use.

•The air conditioner unit must always be stored and transported upright, otherwise

irreparable damage may be caused to the compressor; if in doubt we suggest waiting at

least 24 hours before starting the unit.

•Avoid restarting the air conditioning unit unless 3 minutes have passed since being

turned off. This prevents damage to the compressor.

•Never use the mains plug as a switch to start and turn off the air conditioning unit. Use

the provided ON/OFF button located on the control panel.

•Always place the unit on a dry and stable surface.

•The appliance should not be installed in laundry or wet rooms.

•The appliance must be placed in a room without sources of ignition (for example: open

flames, an operating gas appliance or an operating electric heater).

•R290 refrigerant gas complies with European environmental directives.

•R290 has a low GWP (Global Warming Potential) of 3.

•This air conditioner contains around 280 g of R290 refrigerant gas.

•Do not use or store in an unventilated space with an area smaller than 18.2 m2per unit.

•The room must be such as to prevent stagnation of possible leaks of refrigerant gas as

there could be a danger of fire or explosion should the refrigerant come into contact with

electric heaters, stoves or other sources of ignition.

•Refrigerant gas may be odourless.

•Do not use the product and contact the retailer for advice, if damage has occurred to the

unit which may have compromised the refrigerant system.

•Any repairs or maintenance must only be carried out on the unit by a suitably qualified

engineer. Before opening and servicing the unit the authorised engineer must be in

possession of a copy of the manufacturer’s service manual and must follow the safety

information contained within it to ensure all hazards are minimized.

•The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

•Do not cover or restrict the airflow from the outlet or inlet grills.

•For maximum performance the minimum distance from a wall or objects should be

50cm.

•Keep the filters clean. Under normal conditions, filters should only need cleaning once

every three weeks (approximately). Since the filters remove airborne particles, more

frequent cleaning maybe necessary, depending on the air quality.

•For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees

lower than the current temperature. After, set the fan switch to low and set the

thermostat to your desired setting.

•To protect the unit, we recommend not using the cooling function when the ambient

temperature is higher than 38oC.

FEATURES

•4 in 1 Cooling, Heating, Fan, Dehumidifier. The P12HPW is great for Rooms up to 30 m2.

•3 speed fan: Balancing quiet operation with performance.

•24 Hours Start / Stop Timer.

•Digital Thermostat.

•Remote Control.

•Smart WIFI app control

•Auto-Restart to retain the settings in the event of power failure.

•Castors for Enhanced Portability.

PARTS LIST

Exhau Hosest W n w Slide Barido Drainage pipe

Top Cover

Rear Housing

Carry Handle

Control Panel

Louvres

Front Cover

Castors

Upper Air Inlet

Exhaust Outlet

Lower Air Inlet

Power Cable

Exhaust Hose

Window Slide Bar

Drainage Pipe

INSTALLATION

WARNING: Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another. While moving the unit please note that it must

always be kept upright and then placed on an even surface.

1. Attach the fishtail connector to the end of the hose, by

extending the end and twisting until firmly attached (At least

3 full rotations).

2. Attach the connector on the opposite end of the pipe to the exhaust

outlet on the rear of the appliance by putting into position and twisting

to lock in place.

3. Make sure the unit is upright and there are no obstructions to the air

inlets and outlet grills.

INSTALLATION OF WINDOW KIT

The window kit (slide bar and fishtail) can be used with sliding windows and doors. For other types of window, the

fishtail should be used on its own.

1. Partially open the window and place the

extended slide bar in position before closing

the window onto it.

2. Fix the fishtail adaptor into the

opening on the slide bar

3. Fix the exhaust connector on

the opposite end of the exhaust

hose to the exhaust outlet on

the rear of the air conditioner.

50CM

NOTES:

•The window kit is only designed to be installed with sliding or sash windows or doors. The window

kit is not designed or to be used with any other style of windows.

•The fish tail adaptor can be used without the slide bar with most windows / doors.

•When using the air conditioner ensure that the opening left around the fishtail is as small as

possible as the cooling will be less efficient.

•The best form of installation is through a wall duct. By properly venting you expel hot air from your

room while efficiently cooling it.

•Your air conditioner should be used without the vent pipe in dry mode. When using dry mode

ensure that an external water tank is used, monitored and regularly emptied before overflowing.

Permanent plumbing can be also installed for dry mode or an external uplift water pump can be

set up for unattended use.

IMPORTANT SAFEGUARDS

The length of the soft hose extends from approximately 30 cm to 180 cm. If hose is extended above this

length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well

ventilated and not obstructed as this will cause the unit to overheat. Keep the hose as straight and short as

possible and avoid bending the air hose by more than 30 degrees in order to maintain the performance of

the unit. Excessive bends in the hose may prevent the unit from expelling the hot air, which can lead to

internal damage which would invalidate the warranty.

OPERATION

Press the POWER button to turn the unit ON or OFF.

Press the MODE button to cycle between the 3 modes, the indicator for the selected mode will be

illuminated.

COOL: The room is cooled with the cold air expelled through the front air outlet while hot air is

expelled through the vent pipe. The desired room temperature can be set between 16 and 32

degrees using the + and –buttons, and the fan speed can be changed using the SPEED button.

HEAT: The room is heated with the hot air expelled through the front air outlet while cold air is

expelled through the vent pipe. The desired room temperature can be set between 16 and 32

degrees using the + and –buttons, and the fan speed can be changed using the SPEED button.

FAN: The fan speed can be changed pressing the SPEED button.

AUTO: An intelligent cooling mode where the fan speed is automatically adjusted based on the

amount of cooling required. Attempts to change the fan speed will move the unit into COOL mode.

Repeatedly press the SPEED button to cycle through the three fan speeds. Each time the SPEED

button is pressed, the indicator will change to show the currently selected speed. The fan speed

can be changed between Low, Med and High. The fan speed cannot be changed in DRY mode.

The timer functions cannot be combined or repeated.

POWER ON TIMER

With the appliance in standby, press the TIMER button to set the power-on timer. Use the + and -

buttons to adjust the duration of the timer (1 to 24 hours). The Timer indicator will turn on and the

unit will start after the selected number of hours.

POWER OFF TIMER

With the appliance running with the desired settings, press the TIMER button to set the power-off

timer. Use the + and - buttons to adjust the duration of the timer (1 to 24 hours). The timer

indicator will illuminate and the unit will stop after selected number of hours.

Used to adjust temperature in COOL and HEAT modes and to set the duration of the TIMER. The

buttons are not used in FAN or DRY modes. Press both buttons together to change between

displaying the temperature in Celsius and Fahrenheit.

DRY (DEHUMIDIFY)

The unit should be operated without the vent hose and with the unit set up for continuous

drainage to remove moisture from the air. The unit will operate at low fan speed and will show dH

on the display.

Press and hold the DRY button to turn on the WIFI function, or to change between WIFI

connection methods. See the WIFI section for more information.

Press this button to enable the swing function. When the SWING button is pressed again the

louvres will stop in their current position. Do not attempt to adjust the angle of the blades

manually.

REMOTE CONTROL

NOTE: The design of the remote may vary from the diagram, due to

continuous product improvement.

MULTI PROTECTIVE FUNCTIONS

FROST PROTECTION

In COOL, DRY or AUTO modes, if the temperature of the exhaust is too low, the machine will automatically stop

operating until the temperature has risen.

OVERFLOW PROTECTION

When the water in the internal water tank exceeds the warning level, the machine will stop operating and sound

an alarm with the LCD display showing “E4”. To resume operation empty the internal water tank. After the

water is emptied, the machine will automatically return to the original state.

AUTO-DEFROST

The machine has automatic defrosting function. If during operation the temperature of the internal coils drops

too low, the unit will enter auto defrost and the heating symbol will flash on the control panel.

AUTOMATIC THERMAL PROTECTION

To protect the service life of the machine, the machine has automatic thermal protection. If the temperature

within the unit is outside of the specified range, the compressor and the lower motor will stop operation. The

appliance will automatically return to normal operation after the temperature of the machine recovers.

COMPRESSOR PROTECTION

To prevent damage to the compressor there is a 3 minute delay start protection function.

POWER

Press to turn the unit on or off.

TEMP -

Press to decrease the desired temperature or

timer duration.

TEMP +

Press to increase the desired temperature or

timer duration.

SPEED

Press to change between the three fan speeds.

SLEEP

Press the sleep button to enter sleep mode.

MODE

Press to change between Auto, Cool, Heat and

Fan modes.

POWER

MODE

TEMP +

TEMP - SPEED

SLEEP

EMPTYING THE INTERNAL WATER TANK

MANUAL DRAINAGE:

When the internal water tank is full the unit will stop working.

Shut off the unit and unplug. Try not to move the model abruptly as this

may cause the water in the internal tank to spill out.

Place a tray under the lower water plug or place the unit in a drainage

area.

Unscrew the drain plug cap and remove the rubber stopper - water will

drain from the internal tank. Put the rubber stopper back and screw the

drain plug cap back into place.

CONTINUOUS DRAINAGE:

Unscrew the drain plug cap and remove the rubber stopper.

Connect a water pipe to the upper water outlet.

You can plumb this pipe into your current plumbing system, lead it

outside and use gravity fall or use a water pump.

NOTE:

•This model has a self-evaporative function, which reduces the need to empty the water tank. If the unit

is vented correctly most of the water is reused to cool the condenser coils and any excess is evaporated.

Please do not use continuous drainage if you intend to use the self-evaporating facility.

•When using the unit in heating mode, it is advisable to use continuous drainage.

Andere Handbücher für P12HPW

Inhaltsverzeichnis

Andere ElectrIQ Klimaanlage Handbücher

ElectrIQ

ElectrIQ iQool9PLUS-V2 Betriebsanleitung

ElectrIQ

ElectrIQ eiQ-9WMINV-V2 Betriebsanleitung

ElectrIQ

ElectrIQ A1/CMAC10M Bedienungsanleitung

ElectrIQ

ElectrIQ Slimline ECO AC60E Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT12HPW-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX 15 Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT16-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ P15C Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX15-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-9WMINV-V3 Bedienungsanleitung

ElectrIQ

ElectrIQ P15HP Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-9K9KC18KWMINV Betriebsanleitung

ElectrIQ

ElectrIQ eiQ-12K12KC24KWMINV Betriebsanleitung

ElectrIQ

ElectrIQ P12C Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT8W Bedienungsanleitung

ElectrIQ

ElectrIQ PLM12000HP Bedienungsanleitung

ElectrIQ

ElectrIQ AIRCUBE 10DLX Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT12HPWE Bedienungsanleitung

ElectrIQ

ElectrIQ COMPACT Bedienungsanleitung

ElectrIQ

ElectrIQ CMAC20M Bedienungsanleitung

ElectrIQ

ElectrIQ iQool9 Bedienungsanleitung

ElectrIQ

ElectrIQ Platinum Series Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX15 Bedienungsanleitung

ElectrIQ

ElectrIQ P12CE-V2 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung