ElectrIQ ISLAND eiQTMISLANDSLIM Bedienungsanleitung

Installation and

User Manual

ISLAND COOKER HOOD

eiQTMISLANDSLIM

CONTENTS

Safety Precautions

Introduction

Dimensions

Unpacking your appliance

Product Overview –Parts Supplied

Options for Ventilation

Standard Installation

Installation for Minimum chimney length

Carbon Filter

Operation

Maintenance

Troubleshooting

Manufacturer Support

Environmental protection

Specification

SAFETY PRECAUTIONS

Whilst this product complies with all safety requirements, incorrect

or inappropriate use can lead to personal injury and potential

damage to property. Please read the contents of this instruction

booklet thoroughly before fitting or using this cooker hood.

⚫The cooker hood must be installed in accordance with the

installation instructions provided, making sure all measurements

and guidance are followed.

⚫All installation work must be carried out by a qualified electrician

or a competent person.

⚫If venting externally, make sure the ducting has no bends

sharper than 90 degrees as this will reduce the efficiency and

performance of the cooker hood.

⚫The cooker hood is for domestic use only and is not designed

for commercial use. It should only be used for the purpose it was

intended –to extract vapours and cooking odours.

⚫Do not flambé or use an open flame under the cooker hood.

⚫Do not try to use the cooker hood without the supplied grease

filters, or if the filters are excessively greasy. The filters should

be cleaned regularly following the guidance provided, and

replaced if necessary.

⚫Clean your appliance regularly, by following the method

provided in this manual. Failing to maintain the unit would

increase the risk of fire.

⚫Do not discharge the air into a flue that is used for exhausting

fumes from other appliances burning gas or other fuels.

⚫Do not leave frying pans unattended during use because

overheated fat or oils might catch fire.

⚫If the cooker hood is damaged, do not attempt to use it.

⚫If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or similarly qualified person in

order to avoid an accident.

⚫We advise this cooker hood should not be used by people

(including children) with reduced physical, sensory, or mental

capabilities, or by those who lack experience and knowledge,

unless they have been given supervision and instruction on how

to use the appliance by a person responsible for their safety.

⚫Accessible parts may become hot when used with cooking

appliances.

⚫This cooker hood is not a toy and children should be supervised

to ensure they do not play with it.

⚫The plug must be accessible after installation in case you need

to isolate it in an emergency. If the unit is hard-wired to the

mains via a spur, a fused switch should be installed and

accessible for it.

⚫The minimum distance between the hob surface and the lowest

part of the hood should be at least 65cm. A distance of between

70cm and 80cm gives peak efficiency.

⚫The room MUST be adequately ventilated when the hood is in

use.

⚫Regulations concerning the discharge of air have to be fulfilled.

⚫If used in recirculation mode, the charcoal filters trap odours and

must be replaced at least once a year depending on how

frequently the cooker hood has been used.

CAUTION: Accessible parts of the hood can become

very hot during use with cooking appliances, even when not in

use, due to heat rising from the hob. Sufficient cooling time

should be allowed before touching either the housing or the

grease filters.

INTRODUCTION

Thank you for choosing an electriQ cooker hood.

This instruction manual is designed to provide you with all required

instructions related to the installation, use and maintenance of the appliance.

In order to operate the unit correctly and safely, please read this instruction

manual carefully before installation and usage.

DIMENSIONS OF THE HOOD

UNPACKING YOUR APPLIANCE

•Please take great care when unpacking; a sharp blade should not be

used to open the box, as it may go deep enough inside to damage

components. Components damaged or marked by careless unpacking

are not covered under the guarantee.

•Carefully unpack the contents and check against the next section

(Product overview –parts supplied)

•Packaging materials should be recycled in accordance with local

regulations

PRODUCT OVERVIEW - PARTS SUPPLIED

Description

Illustration

Qty.

Cooker hood

Chimney

Adaptor

Cable Tie

Wall Bracket

Hanging hook

Metal angle bar

Screw (ST4) (4mm x

30mm)

Wall plug

Expansion bolt

(6mm x 50mm)

Screw (M5) (5mm x

10mm)

Screw (self tapping)

(4mm x 6mm)

Nut

Metal washer

Air Flaps

OPTIONS FOR VENTILATION

This hood supports both external venting or recirculation. The type of setup

should be decided before commencing installation.

EXTERNAL VENTING

A flexible pipe is provided which allows the

cooking odours to be extracted outside. If

this is the chosen installation method

consideration to the route of the vent pipe

should be made. The mounting plate

contains a hole allowing the vent pipe to

be connected and routed through the ceiling.

If a vent pipe is to run through the ceiling a hole with a diameter of around

170mm should be made in the ceiling before installation. This would allow the

vent pipe to run through the mounting plate.

RECIRCULATION

This Cooker hood also supports the recirculation of air once

it has passed through the filters. The filtered air is then

expelled through the vent holes in the side of the chimney.

When setting the unit up in this configuration, carbon filters

should also be used to remove odours from the air. Details

of sourcing and fitting the filters can be found in the Carbon

filter section.

STANDARD HEIGHT INSTALLATION

Do not connect the hood to the mains supply before installing it.

1. Position the hanging plate on the ceiling

and then mark the position of the screw

holes with a pencil.

Securely fix the hanging plate to the ceiling,

using the 11 x ST4 (30 mm) screws.

Please ensure that the bracket is fixed in a

way it would support the weight of the hood.

Depending on the construction of the ceiling, alternative fixings may be

required. 6 x expansion bolts are also provided to allow fitting to concrete.

2. Fix the angle bars to the hanging plate, using

the 8 x M5 screws.

3. Extend the angle bars to the required height

and then fix them in position using the 16 x M5

screws. The angle bars must have an overlap

of at least 100mm.

4. At this point, if the unit is to be externally vented

connect the ducting hose to the hanging plate. Then fix

the upper chimney section to the hanging plate, using

the 4 x self tapping screws (4mm x 6mm).

Slide the lower chimney section onto the angle bars and

raise it until it sits just below the upper chimney section.

Use the hanging hook to temporarily keep the lower

chimney section in this position, to make sure that it

does not drop down whilst fixing the main body of the

hood to the angle bars.

5. On the top of the hood unit, where the air outlet vent is located, the 2 x air

flaps should be carefully installed, bending very slightly so the lugs at each

end fit into the holes This enables the flaps to pivot upwards when the unit

is in operation, opening up the outlet fully for the air to pass through.

Please note: The small spindles/lugs at each end of each flap fit into the holes

on the housing, not the grooves above them:

6. Lift the main body of the cooker hood

onto the angle bar and then fix it into

position using the 16 x M5 screws.

IMPORTANT:

This stage of the installation process

MUST be completed by two people, as one

person must support the weight of the hood

until all 16 of the M4 screws have been

securely tightened.

8. The unit should then be connected to a suitable power source, either by

using the supplied plug, or hardwiring the unit into a spur. Please note if hard

wiring the unit, a suitable switch should be fitted in a conveniently accessible

position.

9. Remove the hanging hook and

then slide the lower chimney section

downwards, until it rests against the

main body of the cooker hood.

ALTERNATIVE INSTALLATION FOR MINIMUM CHIMNEY

LENGTH

Do not connect the hood to the mains supply before installing it.

1. Position the hanging plate on the ceiling

and then mark the position of the screw

holes with a pencil.

Securely fix the hanging plate to the ceiling,

using the 11 x ST4 (30 mm) screws.

Please ensure that the bracket is fixed in a

way it would support the weight of the

hood. Depending on the construction of

the ceiling, alternative fixings may be

required. 6 x expansion bolts are also provided to allow fitting to concrete.

2. Calculate the length of the angle bars

according to the overall height of the hood

required. Extend the angle bars to the

required height and then fix them in

position using the 16 x M5 screws. The

angle bars must have an overlap of at least

100mm.

4. On the top of the hood unit, where the air outlet vent is located, the 2 x air

flaps should be carefully installed, bending very slightly so the lugs at each end

fit into the holes This enables the flaps to pivot upwards when the unit is in

operation, opening up the outlet fully for the air to pass through.

Please note: The small

spindles/lugs at each end of each

flap fit into the holes on the

housing, not the grooves above

them:

Inhaltsverzeichnis

Andere ElectrIQ Dunstabzugshaube Handbücher

ElectrIQ

ElectrIQ eiQCH110CEILING Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCANOPY52S Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCHINTGY60 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCHB60B Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCURV60SC Bedienungsanleitung

ElectrIQ

ElectrIQ eiQTOPVWHITE Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ60touchslimhe Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCHFGBSS60 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCURVISL90SS Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ60PBSLIMEN Bedienungsanleitung

ElectrIQ

ElectrIQ eiQSLIM100TOUCH Bedienungsanleitung

ElectrIQ

ElectrIQ eiQTMVISORSTEEL Bedienungsanleitung

ElectrIQ

ElectrIQ eiQTMS60BL Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ60touchslim Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCURV60SCTOUCH Bedienungsanleitung

ElectrIQ

ElectrIQ eiqislandled Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCURV60EN Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCHIM60SC Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ52GCANOPY Bedienungsanleitung

ElectrIQ

ElectrIQ eiQATS60 Bedienungsanleitung

ElectrIQ

ElectrIQ EIQ90CANGW Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ80CURVSCTM Bedienungsanleitung

ElectrIQ

ElectrIQ eiQCHC60W Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ52CANGW Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch