Electro-Harmonix DELUXE MEMORY MAN Bedienungsanleitung

Congratulations on your purchase of the Nano Deluxe Memory Man.

Since its introduction in 1978, the Deluxe Memory Man has been

used on countless recordings and has become the gold standard

analog delay with its warm, pristine tone and reliable, musical

performance. This nano version of the Deluxe Memory Man is a

reissue of the original Deluxe Memory Man, with a few added features

for modern players.

Features Include:

tAdded control over modulation with the addition of a Rate knob

tInternal switch to enable tails or true bypass

tHigh input impedance to preserve your guitar’s tone

tPowered from standard 9VDC, center-negative power supplies

tMore compact, pedal-board friendly footprint

WARNING: This device comes equipped with an Electro-Harmonix 9.6DC-200 power sup-

ply. It requires 150mA at 9VDC with a center negative plug. Use of the wrong adapter or

a plug with the wrong polarity may damage the device and void the warranty. Do not

exceed 12VDC on the power plug. Power supplies rated for less than 150mA will cause

the device to act unreliably.

Nano Analog Delay with Modulation

Controls and Connections

1. DELAY Knob Sets delay time from 30ms to 550ms. As DELAY is turned clockwise, the

delay time increases. Turning the DELAY knob while playing can produce strange, eerie

and unusual pitch-shift effects, especially with FEEDBACK set above noon. Note:

it is normal to hear ring modulation artifacts when DELAY is set above 3 o’clock.

2. FEEDBACK Knob Controls the amount of signal that is circulated from the

output of the delay block back to its input yielding delay repeats, or multiple

echoes. If set very high, runaway oscillation will occur. Fairly high feedback

with short delay settings produces a reverb effect.

3. BLEND Knob Varies the output mix between the dry and delayed signals. The

BLEND knob ranges from 100% dry (CCW position) to 100% wet (CW position).

Set BLEND to the center position for equal levels of both.

- 2 -

Operating Instructions

Connect your guitar to the INPUT jack on the Nano Deluxe Memory Man (Nano DMM)

and the OUTPUT jack to your amp’s input. Plug in the included power supply and

insert its output plug into the power jack. Press the footswitch to ensure the

STATUS LED is lit, now your Nano DMM is ready to go. Have fun experimenting with

the Nano DMM and other effects pedals to develop your own unique sound.

- 3 -

4. DEPTH Knob Sets the amount of modulation that is added to the effect. As

DEPTH is turned clockwise, modulation width increases. Modulation is produced

by sweeping the delay time with a repeating LFO. The Nano DMM’s built-in mod-

ulation produces vibrato style effects when the BLEND knob is set to maximum

or produces chorus type effects when BLEND is set to the middle. Turn DEPTH

down to the full counter-clockwise position to disable modulation.

5. RATE Knob Adjusts the speed of modulation. As RATE is turned clockwise,

the modulation speed increases. The original DMM has a rate switch labeled

Chorus and Vibrato. To achieve the same Chorus and Vibrato settings on the

Nano DMM: set RATE to 9 o’clock for the Chorus setting; set RATE to 2 o’clock for

the Vibrato setting. The DEPTH knob must be set above the full CCW position

to hear the RATE knob change the modulation speed.

6. LEVEL Knob Sets the input gain for the Nano DMM. Both the wet and dry signals

mixed by the BLEND knob go through the gain block. We recommend starting

with LEVEL turned to 12 o’clock, setting the BLEND knob for the proper mix

between wet and dry signals, then adjust the LEVEL knob for an ideal volume

balance between effect and bypass modes.

7. OVERLOAD LED The OVERLOAD LED lights when the delayed signal starts to

smoothly clip.

8. FOOTSWITCH and STATUS LED The footswitch engages or bypasses the effect.

The STATUS LED lights when the effect is engaged. In bypass mode, the STATUS

LED is off.

9. TAILS Switch The internal TAILS switch can be accessed by removing the bottom

cover of the Nano DMM. The switch is located on the small board that holds the

footswitch. When set to TAILS (downward position), any delay echoes that are

present upon entering bypass continue to ring out but no new audio enters the

delay block. When this switch is set to the upward position, the effect instantly

mutes upon entering bypass.

When TAILS is off, the Nano DMM features true bypass; with TAILS enabled,

buffered bypass is employed. By default from the factory, the TAILS switch is

set to the off position.

10. INPUT Jack Audio input to the Nano DMM.

11. OUTPUT Jack Audio output from the Nano DMM.

12. 9V Power Jack Attach the output plug from the included power supply to the

9V power jack. The Nano DMM draws 150mA at 9VDC on a center-negative plug.

Do not exceed 12VDC on the power jack.

Notes and Specications

t Audio input impedance at INPUT jack: 1MΩ

t Audio output impedance at OUTPUT jack: 300Ω

tCurrent draw: 150mA at 9.0VDC

tMaximum input signal level, BLEND = 100% wet: +7.6dBu

tMaximum input signal level, BLEND = 100% dry: +13.0dBu

WARRANTY INFORMATION

Please register online at www.ehx.com/product-registration or complete and return

the enclosed warranty card within 10 days of purchase. Electro-Harmonix will re-

pair or replace, at its discretion, a product that fails to operate due to defects in

materials or workmanship for a period of one year from date of purchase. This ap-

plies only to original purchasers who have bought their product from an authorized

Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the

unexpired portion of the original warranty term.

If you should need to return your unit for service within the warranty period, please

contact the appropriate ofce listed below. Customers outside the regions listed

below, please contact EHX Customer Service for information on warranty repairs

at [email protected]om or +1-718-937-8300. USA and Canadian customers: please obtain

a Return Authorization Number (RA#) from EHX Customer Service before returning

your product. With your returned unit, include a written description of the problem

as well as your name, address, telephone number, e-mail address, RA# and a copy of

your receipt clearly showing the purchase date.

United States & Canada

EHX Customer Service

Electro-Harmonix

co New Sensor Corp.

47-50 33rd Street

Long Island City, NY 11101

Tel: 718-937-8300

Email: [email protected]om

Europe

John Williams

Electro-Harmonix UK

13 Cwmdonkin Terrace

Swansea SA2 0RQ

United Kingdom

Tel: +44 179 247 3258

Email: electr[email protected]om

This warranty gives a purchaser specic legal rights. A purchaser may have even greater rights depending upon

the laws of the jurisdiction within which the product was purchased.

COMPLIANCE

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-

ant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modications not expressly approved by the manufacturer could void the user’s authority to operate the

equipment under FCC rules.

The CE logo indicates that this product has been tested and shown to conform with all applicable

European Conformity directives.

The WEEE or “trashcan” logo indicates that this product is made up of electronic components that should not

be trashed alongside household waste but instead should be recycled by a proper electrical waste facility.

Inhaltsverzeichnis

Andere Electro-Harmonix Musikpedal Handbücher

Electro-Harmonix

Electro-Harmonix Slap-Back Echo Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix 720 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix TUBE ZIPPER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Grand Canyon Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix EDDY Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix MAINFRAME bit crusher Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Super Pulsar Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NANO BIG MUFF PI Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NANO POG Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix XO HUM DEBUGGER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Silencer Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix METAL MUFF with TOP BOOST Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix 8-STEP PROGRAM FOOT CONTROLLER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Stereo Polychorus XO Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NEXT STEP SERIES Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Dual Expression Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix LESTER G Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix OPERATION OVERLORD Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix SPRUCE GOOSE OVERDRIVE Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Triangle Big Muff Pi Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Satisfaction Plus Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Octavix Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix XO ENIGMA: Q BALLS Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix MOD 11 Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung

TREX

TREX ToneBug Totenschläger Bedienungsanleitung

BBE

BBE ORANGE SQUASH Bedienungsanleitung