Electro-Harmonix NANO LOOPER 360 Bedienungsanleitung

NANO LOOPER 360

Compact Looper

Congratulations on your purchase of the Nano Looper 360! The Nano Looper 360 is a

small, extremely easy to use looper with a total of 360-seconds of loop recording time. Not

only that, the available 360 seconds can be divided into 11 different Loops, so you get the

most out of the available memory! You can think of the Nano Looper 360 as your very own

“Loop Locker.”

WARNING: Your Nano Looper 360 comes equipped with an Electro-Harmonix 9.6DC-

200BI power supply (same as used by Boss®& Ibanez®: 9.6 Volts DC 200mA). The Nano

Looper 360 requires 90mA at 9VDC with a center negative plug. Using the wrong adapter

or plug polarity may damage your unit and void the warranty.

–FEATURES –

-6 minutes of loop recording time

-11 selectable, independent Loops, that remain in memory until you erase them

-High quality, uncompressed audio: 24-bit A/D/A, 44.1kHz Sample Rate

-Intuitive looping interface

-Undo-Redo function

-Unlimited overdubbing

-Small pedal board footprint

-AC Adapter Included

-Optionally may use 9V Alkaline Battery, battery life: approximately 4 hours of operation

(varies on conditions of use)

–CONTROLS –

LEVEL Knob –Controls the output level of the Loop. Your dry signal remains at unity

signal level from input to output. The dry signal also remains analog throughout the 360.

LOOP Knob –Selects Loop number: 1-11. When scrolling through loops, the MEM LED

flashes quickly during transitions. If the loop has no recorded memory, the MEM LED

remains off. If the loop has recorded memory, the MEM LED remains on and playback can

begin.

INPUT Jack –This ¼” jack is the audio input for the Nano Looper 360. The input

impedance is 2.2M.

OUTPUT Jack –This ¼” jack is the audio output from the Nano Looper 360. The output

impedance is 470.

9V Power Jack –Plug the output of the supplied AC adapter into the 9V power jack

located at the top of the Nano Looper 360. The Nano Looper 360 draws 90mA at 9VDC

with a center negative plug. The Nano Looper 360 accepts Boss®and Ibanez®style AC

Adapters.

–QUICK START GUIDE –

RECORDING A LOOP

1. To record a Loop; simply select an empty bank and press the Footswitch once. The

REC LED will light solid and recording begins immediately.

2. To stop recording the loop, press the Footswitch again once. The REC LED will turn

off, the PLAY LED will turn on, and the loop will begin playing immediately. The

MEM LED will also light solid, indicating the presence of recorded loop memory.

3. All Loops play indefinitely. Each time the loop repeats, the PLAY LED will turn off

briefly.

4. After a loop is recorded, the length is subtracted from the total loop recording time.

5. Note: if the full 360 seconds of Loop Recording time is reached, recording will stop

automatically. The REC LED will turn off, the PLAY LED will turn on, and the Loop

will begin playing immediately. The MEM LED will also light solid, indicating the

presence of recorded loop memory.

STOPPING & STARTING LOOP PLAYBACK

1. To stop loop playback, press the Footswitch two times quickly.

2. Note: the REC LED will turn on together with the PLAY LED during the first press.

Both LEDs turn off during the second press and playback stops immediately.

3. While stopped, press and release the Footswitch once to start playback. The PLAY

LED will light indicating the loop is playing.

RECORDING AN OVERDUB

1. To record an overdub, make sure a Loop is playing back. If a loop is not playing,

press the Footswitch once to begin playback. The PLAY LED will turn on and the

loop will begin playing immediately.

2. To start recording an overdub, press the Footswitch once. The REC LED will turn

on, together with the PLAY LED, and audio will be recorded on top of the original

loop. No volume loss will occur to the previously recorded portion of the loop.

3. To stop overdubbing the loop; press the Footswitch again once. The REC LED will

turn off, and the loop will continue playing along with the overdubbed audio.

4. Overdubbing will never change the length of the loop.

5. If the loop repeats during overdubbing, the REC LED and PLAY LED will both turn

off briefly. The Nano Looper 360 can overdub indefinitely, allowing you to

continuously overdub new audio onto your loop.

6. After finishing an Overdub, the UNDO-REDO function is enabled. You may undo,

then redo the last Overdub as many times as you like.

UNDO-REDO FUNCTION

1. The Undo/Redo function can only be initiated while a loop is playing back. Undo/Redo

cannot be performed during Overdub, Record or Stop modes.

2. To undo an overdub (remove the last take) during loop playback, press and hold the

Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub

will be removed.

3. To redo an overdub (restore the last take) during loop playback, press and hold the

Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub

will be restored.

4. Note: once UNDO-REDO is enabled, this function is available until the loop is erased.

This is true even if returning to a loop from a previous selection, or even after power

cycling.

ERASING A LOOP

1. To erase a loop, play-back must be stopped. If a loop is playing, press the

Footswitch two times quickly.

2. Press and hold the Footswitch for 2 seconds. The MEM LED will blink six times then

remain off, indicating the loop is erased.

3. Note: the ERASE function is only enabled when the loop has recorded memory, as

indicated by the MEM LED remaining lit.

LOOP MEMORY

1. Any recorded audio is stored automatically to the Nano Looper 360’s internal memory.

2. All recorded loops will remain in memory until they are erased. Power cycling does not

erase loops unless power is cut while recording the loop. Any loop or overdub that

was being recorded at the time of power loss will not be saved by the 360.

3. After a loop is recorded, the length is subtracted from the total loop recording time.

For example, if a 60 second loop is recorded on Loop 1, there are 300 seconds still

available for Loops 2-11. Overdubbing on top of any given loop does not subtract

from total loop recording time.

4. When the full 360-seconds of loop recording time is depleted, recording a new loop

is inhibited. If an empty Loop is selected and recording is attempted, the MEM-LED

will blink twice. To free-up recording memory, select a loop with recorded memory

and erase it.

FACTORY RESTORE

1. To initialize a Factory Restore, unplug the power jack.

2. Set the Loop Knob to Loop 11.

3. Plug in the power jack while holding down the footswitch until all three LEDs begin to

flash, this takes about 2 seconds. Factory restore will not begin until all three LEDs

are blinking. If you change your mind before the three LEDs begin to blink, release

the footswitch or move the LOOP knob to another loop location other than 11.

4. Once all three LEDs start blinking you can release the footswitch. All three LEDs will

continue to flash until the Factory Restore process is complete (~4 seconds). After the

process is complete, the MEM LED will flash quickly and Loop 11 will be selected.

5. Note: All Loop audio is erased during Factory Restore, and the process cannot be

undone.

–CHANGING THE BATTERY –

To change the 9-volt battery, you must remove the 4 screws on the bottom of the Nano

Looper 360. Once the screws are removed, you can take off the bottom plate and change

the battery. Please do not touch the circuit board while the bottom plate is off or you risk

damaging a component.

Battery life is indicated by the three LEDs. These LEDs will fail to turn-on with a dead

battery. If the 360 fully discharges a battery during normal operation, all LEDs will turn-off

and prevent all functions. The battery must be changed immediately.

WARRANTY INFORMATION

Please register online at http://www.ehx.com/product-registration or complete and return

the enclosed warranty card within 10 days of purchase. Electro-Harmonix will repair or

replace, at its discretion, a product that fails to operate due to defects in materials or

workmanship for a period of one year from date of purchase. This applies only to original

purchasers who have bought their product from an authorized Electro-Harmonix retailer.

Repaired or replaced units will then be warranted for the unexpired portion of the original

warranty term. If you should need to return your unit for service within the warranty

period, please contact EHX Customer Service at 718-937-8300 or info@ehx.com for a

Return Authorization Number. Along with your pedal, please include a brief description of

the problem as well as your name, address, telephone number, copy of your receipt, and a

check or money order.

United States - $12 Ship to:

Canada - $15 Electro-Harmonix

Europe and outside countries - $25 C/O New Sensor Corporation

55-01 2nd Street

Long Island City, NY, 11101

Attn: Service Department

Please make checks/money orders payable to New Sensor Corporation.

To hear demos on all EHX pedals visit us on the web at www.ehx.com

Email us at info@ehx.com

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation. If the device is not installed and used in accordance with the instructions, it

may cause harmful interference to radio communications and void the user's authority to

guarantee the equipment.

Note:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the dealer or an experienced radio/TV technician for help.

Modifications not expressly approved by the manufacturer could void the user's authority to

operate the equipment under FCC rules.

Inhaltsverzeichnis

Andere Electro-Harmonix Musikpedal Handbücher

Electro-Harmonix

Electro-Harmonix FLATIRON FUZZ Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix THE ANALOGIZER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix EDDY Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix BLACK FINGER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix XO STEREO CLONE THEORY Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix XO The Worm Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix MOD REX Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NEXT STEP Series Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix SOUL FOOD Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix PICO POG Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Black Finger Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Octavix Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Silencer Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix BASS SOUL FOOD Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NANO POG Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix EHX B9 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Holier Grail Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix GERMANIUM4 BIG MUFF PI Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix HELL MELTER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Triangle Big Muff Pi Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Nano Q-Tron Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix nano FREEZE Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Slap-Back Echo Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Q-TRON Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung

TREX

TREX ToneBug Totenschläger Bedienungsanleitung

BBE

BBE ORANGE SQUASH Bedienungsanleitung