Elenco Electronics Snap Circuits Beginner Bedienungsanleitung

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:26 P Page 1

Conforms to all applicable US

government requirements.

Batteries:

• Use only 1.5V AA type, alkaline batteries (not included).

• Insert batteries with correct polarity.

• Do not mix old and new batteries.

• Remove batteries when they are used up.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (nickel-cadmium) batteries.

• Do not connect batteries or battery holders in parallel.

• Do not short circuit the battery terminals.

• ever throw batteries in a fire or attempt to open its

outer casing.

• Batteries are harmful if swallowed, so keep away from

small children.

-1-

WAR I G: MOVI G PARTS

Do not touch the light motor ( 7)

during operation.

WAR I G: SHOCK HAZARD

Never connect Snap Circuits®to the electrical

outlets in your home in any way!

Table of Contents

Warnings 1

Parts List 2

How to use it 3

Basic Troubleshooting 4

A vance Troubleshooting 4

Project Listings 5

Projects 1 - 21 6 - 26

WAR I G:

Adult Supervision:

Always check your wiring before turn-

ing on a circuit. ever leave a circuit

unattended while the batteries are in-

stalled. ever connect additional bat-

teries or any other power sources to

your circuits. Discard any cracked or

broken parts.

experiments are suitable and safe (the

instructions should enable supervising

adults to establish the experiment’s

suitability for the child). Make sure your

child understands and follows all of the

safety warnings, and keeps them at

hand for reference.

ever modify your parts, as doing so

may disable important safety features

in them, and could put your child at risk

of injury.

Because children’s abilities vary so

much, even with age groups, adults

should exercise discretion as to which

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:26 P Page 2

Important: If any parts are missing or damaged, DO OT RETUR TO RETAILER. Call customer service toll-free at

(800) 533-2441 or e-mail us at: [email protected].

Parts List (Colors and styles may vary) Symbols and umbers

Qty.

ame

Symbol

Part #

Qty.

ame

Symbol

Part #

ini Base Grid

(7.7” x 5.5”) 6SCBG

Lamp

6SCL4

3-Snap Wire 6SC03

Light otor 6SC 7

Battery Holder -

uses 3 1.5V type

AA (not included)

6SCB3B

Slide Switch 6SCS1

Red/Yellow LED 6SCD10

Press Switch

6SCS2

Egg 6SCEGG

Horn

6SCW1

B3B

D10

-2-

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:26 P Page 3

ote: While building the

projects, be careful not to

accidentally make a direct

connection across the bat-

tery holder (a “short cir-

cuit”), as this may damage

and/or quickly drain the

batteries.

How to add or replace batteries

Remove the safety cover from the battery holder (B3B) with a Phillips head screwdriver.

Insert three (3) 1.5V “AA” batteries (not included) into the battery holder (B3B). Be sure

to orient the battery “+” side as marked in the holder.

Replace battery holder cover.

How To Use It

-3-

Placing a 3-snap wire directly

across the batteries is a

SHORT CIRCUIT.

EVER

DO!

When the slide switch (S1) is turned

on, this circuit has a SHORT CIR-

CUIT path (as shown by the ar-

rows). The short circuit prevents

any other portions of the circuit from

ever working.

EVER

DO!

Examples of SHORT CIRCUITS - EVER DO THESE!!!

Do not touch the light motor ( 7) during

operation.

Activate the circuit using the slide switch (S1) or press switch (S2) as in-

dicated in the final step.

Be sure that the light motor ( 7), red/yellow LED (D10, and horn (W1)

have their “+” marking positioned as per the drawing.

For each project, follow the drawings to place all STEP 1 parts on the

mini base grid, then place all STEP 2 parts, then place any additional

parts indicated by STEPS 3 or 4.

Step 1

Step 2

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:26 P Page 4

Basic Troubleshooting:

1. ost circuit problems are due to incorrect assembly, always double-check that your circuit exactly matches the drawing for it.

2. Be sure that the light motor ( 7), red/yellow LED (D10, and horn (W1) have their “+” marking positioned as per the drawing.

3. Be sure that all connections are securely snapped.

4. Try replacing the batteries.

Advanced Troubleshooting (Adult supervision recommended):

If you suspect you have damaged parts, you can follow this procedure to systematically determine which ones need

replacing:

1. Lamp (L4), red/yellow LED (D10), horn (W1), light motor (M7), and battery holder (B7):

A. Place batteries in holder.

B. Place the lamp directly across the battery holder, it should light. C. Do the same with the LED, it should light red or yellow,

depending on how you oriented it.

D. Do the same with the horn (horn + to battery +), it should make an annoying sound.

E. Do the same with the light motor (motor + to battery +), it should spin to the right and its lights should be on.

F. If nothing works, then replace your batteries and repeat, if still bad then the battery holder is damaged.

2. 3-snap wires: Build the Lamp circuit (on page 8), but replace the slide switch (S1) with a 3-snap wire; if the lamp (L4) does

not light then one of the two 3-snap wires in the circuit is broken. Systematically test all four 3-snap wires in your set.

3. Slide switch (S1) and press switch (S2): Build the Lamp circuit (on page 8); if the

lamp (L4) does not light then the slide switch is broken. Replace the slide switch with

the press switch and test it in the same way.

Customer Service

Call toll-free: (800) 533-2441

e-mail: [email protected]

-4-

Troubleshooting

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:26 P Page 5

Project Listings

-5-

1 Light Motor 6

2 Fan 7

3 Lamp 8

4 Re Light 9

5 Yellow Light 10

6 Horn 11

7 Light & Soun 12

8 Light & Soun with Egg 13

9 2-Spee Fan 14

10 2-Switch Everything 15

11 Dim Lights 16

12 Super Dim Lights 17

13 2-Switch Light 18

14 Either Switch Lamp 19

15 Press Light Control 20

16 Soun or Motion 21

17 2-Color Light & Soun 22

18 Fun with Soun & Lights 23

19 Fun with Switches 24

20 Lots of Lights 25

21 Egg Horn 26

Project # Description Page # Project # Description Page #

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:26 P Page 6

Project 1 : L ght Motor

Step 1

Step 3

Step 2

-6-

WAR I G: MOVI G PARTS

Do not touch the light motor ( 7) during operation.

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:27 P Page 7

Project 2 : Fan

Step 1

Step 3

Step 2

-7-

WAR I G: MOVI G PARTS

Do not touch the light motor ( 7) during operation.

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:27 P Page 8

Project 3 : Lamp

Step 1

Step 3

Step 2

-8-

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:27 P Page 9

RED

Project 4 : Red L ght

Step 1

Step 3

Step 2

-9-

Optional

SCB-20 anual_050115.qxp_SCB-20 Draft 5/26/15 4:28 P Page 10

Inhaltsverzeichnis

Andere Elenco Electronics Produkt zur naturwissenschaftlichen Bildung Handbücher

Elenco Electronics

Elenco Electronics Snap Circuits Jr. Select Bedienungsanleitung

Elenco Electronics

Elenco Electronics SC-300 Bedienungsanleitung

Beliebte Produkt zur naturwissenschaftlichen Bildung Handbücher anderer Marken

PASCO

PASCO ES-9080B Bedienungsanleitung

ARBOR SCIENTIFIC

ARBOR SCIENTIFIC 93-3501 Bedienungsanleitung

Alga Science

Alga Science SOLAREXPLORER Bedienungsanleitung

HAKUBUN

HAKUBUN magnet SA Bedienungsanleitung

Aurora

Aurora Plasma Globe Bedienungsanleitung

Dentsply Sirona

Dentsply Sirona Sim Multi Bench Bedienungsanleitung

Circuitmess

Circuitmess CircuitPet Bedienungsanleitung

PASCO

PASCO ME-7018 Bedienungsanleitung

laerdal

laerdal SimBaby Bedienungsanleitung

Einstein

Einstein LabMate+ Bedienungsanleitung

Limbs & Things

Limbs & Things PROMPT FLEX STANDARD Bedienungsanleitung

Horizon Educational

Horizon Educational EDUSTAK JUNIOR Bedienungsanleitung

FUTABA

FUTABA GYC441 Bedienungsanleitung

KMART

KMART Volcano Bedienungsanleitung

Bresser

Bresser Discovery 3-in-1 MicroViewer Bedienungsanleitung

Limbs & Things

Limbs & Things 61141 Bedienungsanleitung

PASCO

PASCO ME-9885A Bedienungsanleitung

BT BT-CSIS Bedienungsanleitung