Elite Screens AR100H2 Bedienungsanleitung

V051616-EA

EDGE FREE

Applies to all available screen materials:

Product Description: The Aeon

Series is a fixed frame projection

technology. The EDGE FREE® des

ign resembles a giant size flat

an installation option to further enhance the frame appearance and

backlighting kit is available

for added visual appearance

Assembly Video:

For further assistance, watch our assembly and installationvideo at

www.elitescreens.com/video/aeon-

assembly

For more information on the LED kit

please visit:

Hardware and Parts List

Please make sure all parts listed below a

re included before installation

A. Elbow joint x 4 pcs

D. Center joints x 2 pcs

G. M6 screw x 2-12 pcs

J. M5x50 screws/anchor x 6 pcs

M. Velvet tape

www.elitescreens.com

Aeon Series

EDGE FREE

Fixed Frame Projection Screen

User’s Guide

CineGrey 3D®, CineGrey and CineWhite™

Series is a fixed frame projection

screen that

uses Elite’s EDGE FREE

ign resembles a giant size flat

panel TV display.

The Aeon includes a

an installation option to further enhance the frame appearance and

sorb projector overshoot

for added visual appearance

For further assistance, watch our assembly and installationvideo at

assembly

or scan the following QR Code:

please visit:

http://www.elitescreens.com/led

re included before installation

Top/Bottom horizontal fame x 4 pcs C. Left/Right

vertical

E. Center Support bar x 1-2 pc F

. Wall brackets x

H. M5x15 screw x 24 pcs I.

M6x12 screw x

K. Rubber hammer x 1 pc

L. Screwdriver x

N. Corner Support Bar (180”-200”) x

Fixed Frame Projection Screen

uses Elite’s EDGE FREE

The Aeon includes a

velvet tape as

sorb projector overshoot

. An optional LED

vertical

frame x 2 pcs

. Wall brackets x

2-3 pcs

M6x12 screw x

2-12pcs

L. Screwdriver x

1 pc

pcs

V051616-EA www.elitescreens.com 2

Frame Assembly

1. Insert the center joint (D) into one of the ½ horizontal frames (B) and fasten it with the two M5x15 screws (H).

2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.

3. Repeat steps 1 and 2 for assembling the second horizontal frame.

Push Push

4. For models 150” and below, insert and slide in oneM6 screw(G) through the channel located on the backeach

horizontal frame section (top/bottom).

Note: For models 180” and above, insert and slide in four M6 screws (two on each frame) through the channel

located on the back of each horizontal frame section(top/bottom). Insert two M6 screws on each vertical frame

section(left/right).

5. Insert the elbow joint (A) into each end of the horizontal frames(B)as shown below.

Horizontal long frame (B)

ElbowJoint

(A)

ElbowJoint

(A)

Horizontal long frame

Place one M6 hex screw (G) in the center for attaching the center support bar (E)

Face up

M6 hex screws (G)

Horizontal frame

Center Joints

Top right Frame Top left Frame

V051616-EA www.elitescreens.com 3

6. Insert the two vertical short frames (C) into the elbow joint (A).

7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below.

Horizontal Long frame(B)

Horizontal long frame (B)

Vertical short frame (C)

push

push push

push

Vertical short frame (C)

Note: For models 180” and above,

ensure two M6 screws (G) are

inserted on each vertical frame

before proceeding to step 7.

Face up

V051616-EA www.elitescreens.com 4

8. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the

M5x15 Screws (H).

Screen Material Installation

1.Lay the screen material completely flat with the front facing down on a clean surface in a horizontal position. The

back side of the screen material should be placed upwards.

Note: The back side of the material has the velcro borders all around the edges.

2. Carefully and gently place the assembled frameon top the screen material as shown below. Make sure to not allow

the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.

Four corners join correctly to form a perfect

square. Use the included screwdriver (L) to

fasten the Mx15 screws (H) into each corner

by aligning the frame screw holes to the

holes in the elbow joint (A).

Screen material back facing up

V051616-EA www.elitescreens.com 5

3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the following

order A→B→C→D (see instructions below for details).

Attach the screen material to the corners as shown below.

4. After all four corners have been attached; please check whether the frame corners are wrapped by the screen material.

If not, please loosen the velcro connection and repeat the above steps so the frame is not exposed.

Note: The black shaded part represents the velcro on the frame. That Velcro end will ultimately

attach with the other velcro end on the screen material.

Note:

Represents the

screen material

2) Fold over and attach

material to thevelcro

strip of the frame.

3) Fold over second side

and attach to frame

4) Repeat until all four

sides are done in the

order A, B, C, D

1) Stretch the screen

material in the direction

of the arrowhead.

A D

C B

V051616-EA

5. Proceed to

attach the rest of the material to the frame as describe

Grasp the middle

of the

material and attach it to the velcro

strip on the frame

Attach in the following sequence

www.elitescreens.com

attach the rest of the material to the frame as describe

d in the illustrations below.

Lay the Velcro end on the screen

material over the Velcro end of the

frame and keep it within the edge.

Proceed

in the following sequence

below ①

②

The key is to attach within the

middle sections of 1 and 2. Then

continue attaching the remaining

unattached areas.

Repeat

the

remaining

three sides in the

sequence A, B, C, D as show

below.

of the

screen

material and attach it to the velcro

Attach in the following sequence

: a-b-c-d

d in the illustrations below.

Lay the Velcro end on the screen

material over the Velcro end of the

frame and keep it within the edge.

in the following sequence

②

The key is to attach within the

middle sections of 1 and 2. Then

continue attaching the remaining

unattached areas.

the

same steps on

three sides in the

sequence A, B, C, D as show

V051616-EA www.elitescreens.com 7

6.If the material is too loose or tight after adjusting all four corner sides, then you will need to reattach the material.

Please follow the steps below to properly remove the screen material from the frame. This procedure will ensure

prolonging the life of the screen material.

Screen Material Removal

1. Detach the velcro from the frame.

2. Gently pull back the material to release the material from the velcro connections on the corners.

Support bar installation (for models under 180”):

1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the support bar

with the M6 hex screws (G)on the top and bottom frames.Then fasten with the M6x12 screws (I).

Move the M6 hex screw (G) to the middle area of the frames.

Align the M6 screws

with the two holes.

Pull back the screen material from

the velcro connection along the

edges of the frame to detach it.

Center Support bar

V051616-EA

Support bar installation

(for models

1. Position the center support bar (E)

and

hex screws (G) in the areas

of the

shown in fig 1. Align the

hole on each end of

the support bar with the

M6 hex screws

(G)

located at the top and bottom frame

sections.Then fasten with the

M6x12 screws

(I).

2. Position the

Corner support bars (N)

fig 2. Align the holes on each end of the corner support

vertical and horizontal frame sections. Then fasten with the

Center Support Bar

Corner Support Bar

Align the M6

screws with the

two holes on the

Corner Support

Bars.

Figure 1

www.elitescreens.com

(for models

180” and above):

and

of the

frame

hole on each end of

M6 hex screws

located at the top and bottom frame

M6x12 screws

Corner support bars (N)

and M6 Hex screws (G)

in the areas of the frame as shown below in

fig 2. Align the holes on each end of the corner support

bars with the M6 hex screws

vertical and horizontal frame sections. Then fasten with the

M6x12 screws (I).

Center Support Bar

Align the M6 Screws with

the two holes located on

the Center Support Bar.

Move the M6 hex screw (G)

to these areas of the frame.

in the areas of the frame as shown below in

bars with the M6 hex screws

located on the

to these areas of the frame.

V051616-EA www.elitescreens.com 9

Notice to Installer:

Please use the following installation instructions to obtain superior optical performance from the CineGrey 3D®

Angular Reflective ALR (Ambient Light Rejecting) Screen.

Make sure to follow these instructions in order for the CineGrey 3D® to perform correctly.

•Angular-Reflective material is not compatible with ultra/short-throw projectors

•Minimum lens throw ratio 1.5x image width

•Ambient light must not come from the same direction as the projector

Since angular-reflective means that the projected image will reflect at the mirror-opposite angle, it

is important to position the projector so that the viewer will get the best possible image.

Step 1: Establish the general “eye level” of the viewers

Step 2: Set the appropriate projection level

Step 3: Adjust the screen height level and projection angle

Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

Figure 2

V051616-EA www.elitescreens.com 10

Velvet Tape Trim Installation

Attention: Installing the velvet trim will reduce the viewing size of your screen. See below illustrations for a

comparison of the viewing size of the before and after edge trim installation using the 100” &120” 16:9 diagonal

models.

100” comparison:

120” comparison:

1) Lay the assembled frame on its back on a clean surface.

2) Measure 10 mm (0.40”) from the edge of the frame to the inside of the material.

The Screen

Before installing the trim strip

After installing the trim strip

Before installing the trim strip

Inhaltsverzeichnis

Andere Elite Screens Projektionsfläche Handbücher

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens Vmax Series Bedienungsanleitung

Elite Screens

Elite Screens Home100IWH2-A Bedienungsanleitung

Elite Screens

Elite Screens Elite Home Series Bedienungsanleitung

Elite Screens

Elite Screens Yard Master Electric Leitfaden

Elite Screens

Elite Screens CineTension Series Bedienungsanleitung

Elite Screens

Elite Screens Spectrum Series Bedienungsanleitung

Elite Screens

Elite Screens ZWBMS-58 Bedienungsanleitung

Elite Screens

Elite Screens EB100HW2-E12 Kurzanleitung

Elite Screens

Elite Screens Sable Frame B2 Series Bedienungsanleitung

Elite Screens

Elite Screens Tab-Tension Series Bedienungsanleitung

Elite Screens

Elite Screens TE200HR2 Bedienungsanleitung

Elite Screens

Elite Screens WB30VW Bedienungsanleitung

Elite Screens

Elite Screens YARD MASTER MANUAL SERIES Bedienungsanleitung

Elite Screens

Elite Screens VMAX 2 Series Bedienungsanleitung

Elite Screens

Elite Screens VMAX2 (Plus) Series Bedienungsanleitung

Elite Screens

Elite Screens aeonclr series Bedienungsanleitung

Elite Screens

Elite Screens Ez-Frame Series Bedienungsanleitung

Elite Screens

Elite Screens Vmax Series Bedienungsanleitung

Elite Screens

Elite Screens F60XWV1 Bedienungsanleitung

Elite Screens

Elite Screens Pro Frame Thin DarkUST Series Bedienungsanleitung

Elite Screens

Elite Screens Evanesce B Series Leitfaden

Elite Screens

Elite Screens VMAX113XWS Handbuch

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

SI Dynamic 2 XL Bedienungsanleitung

Draper

Draper Nocturne+ E Montageanleitung