Elite Screens CineTension 2 Series Bedienungsanleitung

Tab-tensioned Premium Electric Screen

CineTension 2 Series

User’sGuide

Rev. 102510-JA

www.elitescreens.com info@elitescreens.com

ortant

Safety

and

arning Precautions

1. Be sure to read this user guide before use and follow the procedures below.

Please retain this manual for future reference.

To avoid any damage, do not use in conjunction with any accessories not recommended by the

manufacturer. Handle the device carefully during transportation to avoid damage.

To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

The power outlet supplying power to the unit should be close to the unit and easily

accessible.

Do not install the device on uneven or inclined surfaces.

Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

Never overload the power cord to prevent an electric shock or fire.

Guard the device from any liquid or foreign objects to avoid electrical shock or fire due to loose

contact or short circuit.

There are no user serviceable parts in the device. Do not attempt to disassemble this device by

yourself. No one except authorized technicians can open this device to make repairs.

Make sure the power source this device is connected to has a continuous power flow.

If there is a need to use an extension cord, make sure the cord has the same equal rating as the

appliance to avoid overheat.

Do not handle the power plug when your hands are wet or your feet are in contact with water.

2. Do not use this device under the following circumstances:

Disconnect the power cord under the conditions of heavy rain, wind, thunder or lighting.

Avoid direct sunshine, rain shower or moisture.

Keep away from fire sources and high temperature to prevent this device from overheating.

Cut off the power supply first before transportation or maintenance.

Fully disconnect from the power supply when screen is not in use for a long period of time, as

should be done with any other electric household appliance.

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious damage

or if there are any evident broken parts

arning

Red

2V (+)

Green 0V (-)

5-12 volt trigger adaptor cable

IR ”eye”receiver

2x AAA

Batteries

IRRemote RF Remote Wall box switch

Bubble leveler

Standard accessories for CineTension 2

Control System

The screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra black drop in

the roller. Please be aware of this as it will void the limitation of your warranty.

Changes or modifications (except cutting the power cord for hardwire installation) to this product not

expressly approved by Elite Screens is prohibited and will void the warranty.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

9Reorient or relocate the receiving antenna of the device which may be causing interference

9Increase the separation between the screen and the device’s receiver

9Connect the equipment into a different power outlet than the device’s

1. 5/12V Trigger: The built-in 5/12V trigger

input for your new CineTension2 allows your screen

to synchronize its drop and rise with the projector's power

cycle. The screen drops when the projector powers up and

retracts when the projector powers down. The 5/12 volt

adaptor connects to your projectors trigger output via a

separate cable that may or may not be provided by the

projector manufacture. The trigger feature will not work

without an output cable from the projector, but it can be

tested using a 9-volt battery by simply connecting the Red

(+) and Green (-) cable to the 9-volt battery.

3-prong power cable

Red: DC 12 +

Green: 0 V -

RJ-45 input connection for

5/12 volt trigger inside

case

lease read this

de prior to installation.

●Make sure the current rating is equal to that of the appliance rating when an extension cord is used.

●Do not use any accessories not provided by the manufacturer with this screen. We will not be responsible for

any risks of fire, electric shock, or injuries resulting from the misuse of this product with accessories not

designed for use with this product.

●Make sure the screen is mounted in a horizontal level position. We suggest consulting with a professional if

you are unsure on how to perform a proper installation.

Bubble Level: Included with the installation package is a small bubble leveler that can be useful in

determining if the screen is perfectly level when installing.

NOTE : ①Please use the Down sign side as the bottom.

②

The Bubble should be in the middle position to determine that it is level.

Sensor

3-way Wall box switch

Senso

2. Wall Box and IR (Infrared) Eye Receiver: The 3-way Wall Box switch enables the consumer to

manually operate the screen's drop/rise capabilities. The IR “eye” protrudes from the bottom of the casing to present a low

profile line-of-sight control option for your IR remote. It is a low-visibility alternative to using the wall box kit and its

ability to protrude from the bottom of the screen allows line-of-sight control even in a recessed ceiling installation.

INSTALLATION

The CineTension 2 series screen is designed for installation on either a wall or ceiling. All hardware is included to

allow either installation method however we do strongly recommend a professional installation for safety purposes.

The extruded hanging brackets are designed to slide anywhere on the back of the screen to accommodate a

wall or ceiling installation and provide an easy alignment with wood studs and trusses.

Please follow the steps below for recommended installation instructions.

Mounting Hardware Kit – Please make sure all of the following items have been supplied before proceeding

installation.

Parts identification:

1. Begin by sliding the Bolts (B) thru the left and right slide channel located on the top back of the CineTension 2

screen’s casing as shown on picture.

2. Slide the Extruded Hanging Brackets (D) thru the rail located below the slide channel until it meets with the top part

of the bolts (B) and then slightly tighten the lug-nuts located on the top and bottom of the bolt with a wrench to secure

the extruded hanging brackets.

Qty 2 –Extruded Hanging

Brackets

(Qty 3 on 120 models and above)

Qty 2 - Bolts

Qty 2 – Screws

Qty 2 – Drywall Anchors

The IR receiver will be connected from the screen

IR “eye” sensor

11.65 mm. in width

Power cord

rox. 6 ft. len

th.

Although the IR remote requires a direct line of sight with the IR sensor to

function, the screen’s case can be hidden from sight and operated using the

RF remote. When depressing the directional buttons you should hear a faint

click signifying that the mechanism is working properly.

80mm in width

3. Mark the location of where the screen is to be installed and drill your hole. Insert the proper screw into the drilled

hole and finish tightening the bolts to the bracket.

4. Examples of an installed CineTension 2 on a wall, ceiling and enclosed.

Flush mount

to wall Flush mount

to ceiling Enclosed

installation

*Allow 2” of spacing

between the front and

back of the screen casing.

Top hole for ceiling installation

Back hole for wall installation

Stop

Down

IR RF

* Please remember to always point to either the IR “eye” sensor or the IR receiver located on the screen’s case using the

IR remote. The IR remote can also work with a Universal Learning Remote Control usually by programming the Screens

IR codes into your Universal Learning Remote.

REFERENCE

ONLY:

(Attention: This adjustment is not required. The screens tension has been se

to achieve its

best performance. Always contact an Elite Screen Technician for assistance to avoid

damaging the screen and voiding your warranty.)

This is the IR (Infra-Red) remote with a

range of approximately 15 Ft.

Battery size AAA

This is the RF (Radio Frequency) remote

with a range of approximately 100 Ft.

Battery size AAA

Pulling the knob and turning it Clockwise it will create more tension to the screen. By

ulling the knob Counter-clockwise it will start to release tension.

Remote Controls

If the electric screen does not move,

lease check the followin

1. Check the power supply first. The screen will understandably not move without power.

2. Make sure the power cord is firmly plugged to the power outlet.

3. Make sure that all cable connections are secure.

4. If the screen works well with the line switch but not with the remote control, please make sure the remote

controls have fresh batteries or replace them with new ones. Change the battery every 6 months to ensure

proper operation of the remotes.

5. For all other

roblems,

lease contact Elite Screens at Techsu

ort

elitescreens.com

1. Q: Wh

does m

screen no lon

er function?

A: There are a few

ossible thin

ou could check:

2. Q: How is the screen material cleaned?

A: The screen material can be cleaned with mild soap and water.

A.)Make sure your wall plug has power and that the screen is properly plugged in.

B.) Please check the fuse to your screen. (Call Tech support for location of fuse)

C.) If screen works well with the line switch but not with the remote control, make sure the remote control

has good batteries in it.

D.) Our electric screens with a tubular motor installed are equipped with a Thermal relay. This would

include all Home 2, CineTension 2 series, and VMAX screens with a diagonal size above 180". This

feature will automatically shut off screen in the event the motor becomes too hot, preventing overheating

of the motor. To correct this, let screen alone for 10-15 minutes and try again.

3. Q: What type of batteries do the remote controls require?

A: The IR and RF remote controls use AAA alkaline batteries

4. Q: Can you manually pull down the screen?

A: No, manually pulling down the screen will damage the electronic motor rolling system.

5. Q: How could I setup my Screens IR receiver to work with my learning remote control system? Do you have any IR

codes I can use to achieve this?

A: Our IR remote controls have been evaluated and entered in to the databases of some Universal remote control

manufacturers. Please contact the manufacturer of your remote to inquire about your remotes ability to function with

ours. If they have not evaluated our remote control then the following list of Binary codes will be used for most remote

setups.

For Spectrum, VMAX2 (Plus), Home2 and CineTension 2 Series

Up: 1111 0000 0001

Stop: 1111 0000 0010

Down: 1111 0000 0100

6. Q: What is the gain on the matte white screen material?

A: The matte white material has a gain of 1.1. For detailed specs, info please check our web-site for more details

For Warranty and Service requests please fill out a RMA /Service Form at:

http://www.elitescreens.com/service_form

Please Visit this link for full Warranty information:

http://www.elitescreens.com/warranty

Remember to register your product at

www.elitescreens.com/register

Warranty Policy

• Two (2) year warranty parts and labor from purchase date as follows (except for refurbished

units as specified below)

• Refurbished units carry a 90-day parts and labor warranty.

• Each party will be responsible for one way shipping during the warranty period.

• DOA (Dead On Arrival): Must be reported within 7 business days of receipt. An RMA

(Return Merchandise Authorization) number must be issued in order to process a replacement.

Elite Screens will replace the DOA unit with a brand new replacement *(see exceptions below)

after the DOA unit is received and/or confirmed defective. Once the product is received, Elite

Screens will send out a new* unit to the customer by ground service (based on stock availability).

Should a problem be reported after the 7-day grace period, the item must be shipped to us for

warranty repair.

• DO NOT return any unauthorized items to Elite Screens, as they will be refused.

The RMA number must be included on the outside label of your shipping box and shipping

documents. Our warehouse is not authorized to accept returns without an RMA number on the

shipping label. RMA numbers are valid for 45 days from the date of issue.

• Missing Parts must be reported within the 7-day (DOA) grace period. If reported after 7 days,

customer will be only responsible for shipping and handling fees. If reported after 30 days of

receipt, customer is responsible for cost of the parts and shipping & handling fees.

*A new or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished)

or based on stock availability.

For US and Canada only

Contacts

US & Canada Tech Support & Warranty Claim

Please contact us at [email protected] or call +1 877-511-1211 #3 Service

Europe Tech Support & Warranty Claim

Please contact us at [email protected] or call +49-(0) 40-30392958

Asia Tech Support & Warranty Claim

Please contact us at [email protected] or call +86-(0) 755-8461-7989

Taiwan Tech Support & Warranty Claim

Please contact us at [email protected] or call +886-(02) 2747-8979

America:

Elite Screens Inc

16410 Manning Way

Cerritos, CA 90703 USA

Tel: +1-562-483-8198 (877-511-1211)

Fax: +1-562-483-8498

info@elitescreens.com

www.elitescreens.com

Europe:

Elite Screens Europe GmbH

Lübecker Straße 1

22087 Hamburg, Germany

Tel: +49-40-30392494

Fax: +49-40-49219200

[email protected]

www.elitescreens.eu

Elite Screens France S.A.S

11, Allée William Penn

92150 Suresnes, France

Tel: +33-1-45064735

Fax: +33-1-45064735

[email protected]

www.elitescreeens.com/fr

Latin America Contact:

info.la@elitescreens.com

East Asia Contact:

info.ea@elitescreens.com

India Contact:

[email protected]

Japan Contact:

info.japan@elitescreens.com

Asia:

Elite Screens China Corp.

Longxi Duimianling Industry Zone Longcheng

Longgang District,

ShenZhen GuangDong, China

Tel: +86-(0)755-8461-7989

Fax: +86-(0)755-8461-7669

info@elitescreens.com.cn

www.elitescreens.com.cn

Taiwan:

Elite Screens Taiwan Co. Ltd.

4F., No. 42-1 Wuguan Rd. Wugu Township

Taipei County 248, Taiwan (Wugu Industrial Park)

Taiwan (R.O.C)

Tel: +886+2+8990+1999

Fax: +886+2+8990+1366

info@elitescreens.com.tw

www.elitscreens.com.tw

Andere Handbücher für CineTension 2 Series

Inhaltsverzeichnis

Andere Elite Screens Projektionsfläche Handbücher

Elite Screens

Elite Screens SilverFrame 100GH1 Bedienungsanleitung

Elite Screens

Elite Screens AR2 Series Bedienungsanleitung

Elite Screens

Elite Screens Yard Master Electric Leitfaden

Elite Screens

Elite Screens Insta-RP Screen Series Bedienungsanleitung

Elite Screens

Elite Screens Ez-Frame Series Bedienungsanleitung

Elite Screens

Elite Screens Pro Frame Thin DarkUST Series Bedienungsanleitung

Elite Screens

Elite Screens Spectrum Series Bedienungsanleitung

Elite Screens

Elite Screens Edge Frame Bedienungsanleitung

Elite Screens

Elite Screens F100XWH1 Bedienungsanleitung

Elite Screens

Elite Screens aeonclr series Bedienungsanleitung

Elite Screens

Elite Screens VMAX113XWS Handbuch

Elite Screens

Elite Screens EDGE FREE Aeon Series Bedienungsanleitung

Elite Screens

Elite Screens Ez-Frame Series Bedienungsanleitung

Elite Screens

Elite Screens OMS90H2 Bedienungsanleitung

Elite Screens

Elite Screens YardMaster Manual Series Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens DIY Screen Series Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens Aeon CineGrey 3D AT Series Bedienungsanleitung

Elite Screens

Elite Screens ezFrame Series Bedienungsanleitung

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Elite Screens

Elite Screens EZ-Cinema Series Kurzanleitung

Elite Screens

Elite Screens SilverFrame 100GH1 Bedienungsanleitung

Elite Screens

Elite Screens VMAX 2 Series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

SI Dynamic 2 XL Bedienungsanleitung

Draper

Draper Nocturne+ E Montageanleitung