Elk Products ELK-M1G Montageanleitung

INSTALLATION

MANUAL

Cross Platform Control

Specifications, Installation and Programming

M1 includes the SIA CP-01 Standards for False Alarm Reduction †

L520 Rev. K 10/4/13 Current with Firmware 5.3.0

M1G Installation and Programming

Page 2

Introduction

LIMITATION

The ELK-M1G Control is designed to warn against unauthorized entry and other situations. However, it is not a guarantee of protection against

the occurrence of burglary, fire, or other emergency. Any alarm system is subject to compromise or failure to warn for various reasons. For

example:

- Unauthorized access can be gained through unprotected points or by disarming or bypassing protected points.

- Sensing devices are power driven and do not operate without electrical power. Battery-operated devices will not work without batteries, with

dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any

reason, however briefly.

- Telephone lines over which alarm signals are transmitted may be out of service or rendered inoperable by an intruder.

- Even if the system responds to the emergency as intended, occupants may have insufficient time to protect themselves from the emergency

situation. In the case of a monitored alarm system, authorities may not respond appropriately.

- Smoke detectors have limitations and cannot detect all types of fires. According to data published by the Federal Emergency Management

Agency, while smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide

early warning for a variety of reasons in as many as 35% of all fires, . Some of the reasons some detectors used in conjunction with this

System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense

fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke

detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor

or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general,

detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas,

improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending an the nature of the

fire, and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all

occupants to escape in time to prevent injury or death..

- Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path

has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.

- Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions. Longevity of

batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External

factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given

installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of battery to

maintain protection for that given point within the system.

- Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance.

Homeowner, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and

property.

- A user may not be able to reach a panic or emergency button quickly enough.

- Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive

Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected

in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed

doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows

or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the

ambient temperature of the protected area approaches the temperature range of 90 to 105F (32 to 40C), the detection performance can

decrease.

- Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of

closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, they are less likely to

waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a

stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-

impaired people.

- This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 20

years, the electronic components could fail at any time.

- The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm

system should be tested weekly to make sure all sensors and transmitters are working properly.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,

photocopying, recording, or otherwise without the prior written permission of the manufacturer. The material in this publication is for information

purposes and subject to change without notice. The manufacturer assumes no responsibility for any errors which may appear in this publication.

Printed in U.S.A.

Use of this control for fire detection and/or annunciation may not be permitted by certain states, counties, municipalities or local jurisdiction. It is

the responsibility of the installing alarm company to check with the local A.H.J. (Authority Having Jurisdiction) or State Fire Marshal’s office prior

to using this control for fire detection.

M1G Installation and Programming Page 3

Table of Contents

Specifications, Features, and Benefits ..................................................................................................... 5

Wiring & Hookup Diagram ........................................................................................................................... 6

Section 1 - Installation and Wiring ............................................................................................................. 8

1.1 Planning the Installation ...................................................................................................................... 8

1.2 Parts Diagram & Descriptions ........................................................................................................... 8

1.3 Mounting and Wiring Preparation ....................................................................................................... 8

1.4 Control Wiring .................................................................................................................................... 9

Data Bus E.O.L. Termination - VERY IMPORTANT! .............................................................................. 12

Section 2 - Operating the System ............................................................................................................ 14

2.1 Introduction ....................................................................................................................................... 14

2.2 Powering Up (One Keypad) ............................................................................................................. 14

2.3 User Codes and Authorities .............................................................................................................. 14

2.4 Installer Program Code and Authorities ............................................................................................ 14

2.5 Keypad Overview ............................................................................................................................. 15

Keypad Menus ........................................................................................................................................ 16

Menu 0 - Select Keypad Alternate Area - Multi-area (Partition) Operation .............................................. 20

Section 3 - Programming The Control ..................................................................................................... 21

3.1 Introduction ....................................................................................................................................... 21

3.2 Local Keypad Programming ............................................................................................................. 21

3.3 Local or Remote Computer Programming (ELK-RP) and Anti-Takeover ......................................... 21

3.4 Area Partitioning ................................................................................................................................ 21

3.5 Communicator Setup Checklist ....................................................................................................... 22

3.6 Entering Installer Level Programming ............................................................................................... 22

Menu 01 - Bus Module Enrollment .......................................................................................................... 24

Menu 02 - User Code Options ................................................................................................................ 25

Menu 03 - Area Definitions ...................................................................................................................... 26

Menu 04 - Keypad Definitions ................................................................................................................. 28

Menu 05 - Zone Definitions ..................................................................................................................... 30

Menu 06 - Alarm Duration Timers ........................................................................................................... 33

Menu 07 - Global System Definitions ..................................................................................................... 34

Menu 08 - Telephone Account Setup ...................................................................................................... 38

Menu 09 - Area Reporting Codes ........................................................................................................... 40

Menu 10 - Zone Reporting Codes ........................................................................................................... 42

Menu 11 - Keypad F-Key Reporting Codes ............................................................................................ 43

Menu 12 - Sys Report Code Options & Codes ...................................................................................... 44

Menu 13 - User Report Codes................................................................................................................ 46

Menu 14 - Wireless Setup ...................................................................................................................... 47

Section 4 - PC Programming and Automation Capabilities .................................................................... 49

4.1 ELK-RP Software ............................................................................................................................ 49

4.2 Update/Verify Firmware in the Control and Peripherals ................................................................... 50

4.3 Automation Rules and Attributes ...................................................................................................... 51

Appendix A - Event Codes ........................................................................................................................ 58

Appendix B - Telephone Remote Control ............................................................................................... 60

Appendix C - Voice Message Vocabulary *RP only * ............................................................................. 62

Appendix D - Two Way “Listen-in/Talk” Interface................................................................................... 64

Appendix E - SIA CP-01 Compliance ........................................................................................................ 65

Appendix F - Regulatory Agency Statements .......................................................................................... 66

Appendix G - Additional ELK-M1KP Keypad Information ...................................................................... 69

Index ............................................................................................................................. 71

M1G Installation and Programming

Page 4

OUT3 On LED

J-16 Programmable Outputs

See Note 1

& Note 2

PLC ††

Lighting

Interface Conn.

1 WAY (PL513/PSC04)

Select PLC Mode

2 WAY (TW523/PSC05)

JP2

RS232 CONN.

Bell (Supervised)

Voice/Siren † †

Dry Contact Relay

rated 4A @

12 - 24VDC

See Note 2

OUT 1 OUT 3

N/C

COM

N/O

OUT 2

RED

BLACK

WHITE

GREEN

+VAUX

+12VDC Auxiliary Power

(3)

1.25 Amp PTC protected

Grey

Brown

Red

Green TELCO

LINE

HOUSE

PHONES

NEG

Z10

Z11

NEG

Z13

NEG

Z15

Z14

Z12

NEG

Z16

+SAUX

NEG

+VAUX

NEG

+VAUX

NEG

+VAUX

NEG

16.5 V

+VKP

DATA B

DATA A

NEG

OUT 16

OUT 15

OUT 14

OUT 13

OUT 12

OUT 11

OUT 10

OUT 9

OUT 8

OUT 7

+12V

NEG

RING

TIP

Serial Port ††

for Computer/ELKRP

See Manual

Audio Network Interface ††

Keypad &

Data Bus

J2 J1

16 Zones expandable to 208

Do Not

Connect to

a Phone

Line!

Not Used -See Note 3

BATTERY

SW1

12V Battery

7 to 18 Ah

Keypad

Control specifications subject to change without

notice. All circuits are power limited except for

Battery leads.

Complies with FCC Part 68:

Reg. # US: 5K6AL03BELK-M1 REN: 0.3B

Use Standard Jack: USOC RJ-31X.

Serial Number located below on base.

Complies with part 15 of FCC rules.

This Class B digital apparatus complies with

Canadian ICES-003.

See Note 2

+SAUX

+12VDC Switched

Smoke Power

1.1 Amp PTC protected

NEG

DATA B

+12V

JP3

Jumper to start with

no AC - See Note 4.

Power

Status

Reverse

Bat Leads

UL Listed Transformer,

Class 2, 16.5VAC, 45VA

Do not connect to a

switched outlet.

ELK-TRG1640

NORMAL

ZONE 16

JP1 SMOKE

2WIRE

TELCO SEIZED

DIALER ACTIVE

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL

2-Wire Smoke Detector - Zone 16 ONLY

4-Wire Smoke Detector - Any Zone

U.L. Listed EOL Supervision Relay, ESL #204A or equiv.

Use 2,200 Ohm EOL resistor, part # ELK-ER2200. Set

JP1 to 'Normal'.

DATA A

-See Note 2

Data Bus Terminating Resistor

See Note 1.

Data Bus

See Note 1

1.25 Amp PTC

protected

08/13

ELK

PRODUCTS, INC.

HILDEBRAN, N.C., 28637, USA

Cross Platform Control

PSC05

††or

Equivalent

ELK-M1

StripStrip Wires to 1/4" Length

820

Ohm

EOL

NEG

Z16

2. OUT 1 †† for speaker(s) ONLY (4 to 8 Ohms).

If connecting more than 2, use series/parallel

wiring to avoid going below a 4 ohm total load.

OUT 2 Connect ONLY 1 UL Listed Bell or

Siren (self-contained). Current limited to 1 Amp.

Program Global Option 26 to Voltage. This

output supervised. Speaker(s) only permitted

for non-UL installations. Series/parallel wire to

avoid dropping below a 4 ohm total load.

OUT 3 NO/NC dry contact relay rated 4A.

OUT 7 through 16 are +12V switched positive

voltage outputs rated at 50mA max.

3. This terminal (formerly earth gnd) not used.

Do not connect any neg terminals to ground.

4. If AC fails, control will shut down if battery

drops below 10.2 Volts. To start the control with a

good battery and no AC, short the silver pads

momentarily. Replace Battery every 3-5 years.

Test regularly with ELK-BLT Battery Life Tester.

O - I - B A +

† Not Evaluated by UL

†† Not for use in UL Listed Systems

HA008F

2200

Ohm

EOL

To Zone Input

N.O. Alarm Contacts

+SAUX

To Zone NEG

NEG

Aux Data Bus ††

Notes

1. Refer to Appendix F located in the Installation

Manual #L520 Rev. K for the UL limitations on

total continuous 'standby' current drain from

terminals +SAUX, +VAUX, +VKP, and J16.

To configure Zone 16 as a 2-wire smoke zone,

set Jumper JP1 to '2WIRE SMOKE' and use 820

Ohm EOL resistor, part # ELK-ER820

Use Only Compatible Detectors

Control Compatibility Identifier: M10001

Refer to the Wiring & Hookup Diagram in the

Installation Manual # L520 Rev. K for the 2-Wire

Smoke Detector Compatibility chart.

TEST SYSTEM WEEKLY

M1G Installation and Programming Page 5

General:

• Large zone capacity: 16 on-board zones expandable to 208

• Up to 144 of the expandable zones may be wireless using

the ELK-M1XRFTW Wireless Receiver

• Two Way Listen-in interface †

• Flash Memory - Allows field updates to firmware electronically

• RS-232 serial port to interface PCs and peripheral devices

• Time/Date stamped 512 event history log

• Menu driven, text keypad programming - no manual required!

• Voice announcement of alarms, zone descs, status, etc.

- 500+ Word/Phrase Vocabulary

- Link up to 6 words/phrases per announcement

- 10 custom recordable words/phrases

• 13 On-Board Outputs: 1 voice driver/siren, 1 siren driver/

voltage, 1 form “C” Relay, and 10 low current (50 mA) voltage

outputs

• Supports 4 wire (any zone) and 2 wire (zone 16) smoke

detectors

• Includes Fire alarm verification routine

• Can be partitioned into 8 areas and account numbers

• User Codes:199 (4 or 6 digit) with assignable authority levels

• Arm levels: Away, Stay, Stay Instant, Nite, Nite Instant, Vacation

• Plug-in terminal blocks make service and pre-wires a snap!

• Hardware "watchdog" and nonvolatile EEPROM memory

• Supervised phone line, alarm output, and aux. overcurrent

Communications

• True V.22 bis Modem for fast reliable upload/download

• Optional M1XEP Ethernet Interface †for user operation,

alarm reporting, programming, and more

• Built-in Phone Remote Control makes any phone a keypad

• Integrated Voice Dialer uses vocabulary or custom words

• Communicator formats: SIA, Contact ID, 4 + 2, and Pager

• Installer telephone (buttset) test feature

• Elk-RP PC programming software with conflict resolution to

easily highlight differences between control and PC

- Dial-up, ethernet, RS-232 port, or local house phone jack

- Automatic answering machine bypass

Keypad

• Backlit, Large Character LCD Display, 16 x 2 lines

• Built-in Temperature Sensor

• Optional Plug-in Prox Access reader (26 bit Weigand format)

• Menu navigation keys and 6 programmable function keys

• Plug-in connector, only 4 wires to the control

• 1 Zone input and 1 Output Programmable per Keypad

• Programmable display of time, date, & temperature

• Displays system diagnostics and settings.

• Maximum Keypads allowed: 16

Automation & Integration

• Create lifestyle enhancing comfort, convenience, and security

• Powerful “Whenever/And/Then” RULES Programming allows

almost any imaginable operation. No need to chain rules

together. Any single “Whenever” event can have one or more

ANDs and THENs (conditions and commands).

• Rules utilize easy to understand text based references

• Control lighting using RS-232 serial or 2-way Power Line

Control (PLC) Commands include On, Off, Dim, All On, All Off †

• Transmit and receive custom serial ASCII strings

• Read Temperature Sensors - Communicate with Thermostats

• Turn on Tasks, Lights, Outputs via Keypad or Telephone

•Sunset/Sunrise calculation and activation built-in

Power Supply

• Heavy duty - 2.5 Amp power supply

• Dynamic battery test

• Master power switch and Low battery disconnect

• PTC (fuseless) resettable overload protection

• Multiple auxiliary power terminals

Part Numbers and Accessories:

ELK-M1GCB M1G Gold Board Only (No Teminals Blocks)

ELK-M1GOLD M1G Gold - Control in 14” metal can

ELK-M1GK M1G Gold Kit - No Metal Can, for use with

structured wiring systems

ELK-M1SYS4 M1G Gold Kit - 14” metal can, Ctrl, Encl, Xfmr,

KP, 12V-8Ah, Spkr, RJset

ELK-M1KP Keypad, LCD,16 character x 2 line

ELK-M1KP2 Small LCD Keypad, 16 character x 2 line †

(no internal temp sensor and 2 less “F” keys)

ELK-M1KPAS Keypad Arming Station †

ELK-M1XIN 16 Zone (input) expander

ELK-M1XOVR 16 Output expander, 8 Voltage/8 Relays

ELK-M1RB Relay board, 8 form ”C” relays

ELK-M1DBH Data bus wiring hub “Passive” †

ELK-M1DBHR Data bus wiring hub “Active” for Retrofit †

ELK-M1XEP Ethernet Port Exp/Interface †

ELK-M1XRFTW Two-Way Wireless Receiver for ELK 6000 Xmtrs

ELK-M1XRFEG Wireless Receiver for GE Xmtrs †

ELK-M1XRF2H Wireless Receiver for Honeywell 5800 Xmtrs †

ELK-M1XSP Lighting, Thermostat Interface & Serial exp. †

ELK-M1PR Mini prox reader for keypad †

ELK-M1TWI Two Way Listen-in Int. w/3 mic inputs †

ELK-M1TWS Speaker & Mic for Two Way Listen-in †

ELK-M1ZTS Zone Temperature Sensor -50 to 140 F †

ELK-RP PC software - Free upon request with

Control Panel purchase

ELK-RM Remote “User” Management software

Highlighted Features of the M1G (Gold)

• Automation (“Whenever/And/Then”) Rules Capacity 528

• Serial (RS232) Port Supported 8 w/expanders

• Phone Number Capacity 8

• Number of HVAC Thermostats †Supported 16

• Total Number of Outputs Supported 205

• Advanced Lighting †Options (Pre-set Dim, Extended, Levels, Scenes) Yes

• Analog Zone Definitions Supported Yes

Specifications, Features, and Benefits

† Not evaluated by UL †† Not for use in UL Listed Systems

NOTE: Use of Two Way Listen-in may be regulated by local or state laws and/or ordinance. It is the responsibility of the

Installer to check before using this feature.

M1G Installation and Programming

Page 6

+SAUX

NEG

+VAUX

NEG

+VAUX

NEG

+VAUX

NEG

NORMAL

ZONE 16

JP1

SW1

16.5 V

JUMPER TO START

WITH NO AC

POWER

TELCO SEIZED

NEG

Z10

Z11

NEG

Z13

NEG

Z15

Z14

Z12

NEG

Z16

NEG

Auxiliary +12VDC Power Outputs protected by 1.25A PTC NOTE:

Refer to Appendix F for the UL limitations on total continuous 'standby'

current drain from terminals +SAUX, +VAUX, +VKP, and J16.

Replace Battery every 3-5 years. Use ELK model # ELK1280 (12V - 8 Ah) or ELK12180 (12V - 18 Ah) or equivalent.

DIALER ACTIVE

SMOKE

2WIRE

STATUS

REVERSE

BAT LEADS

N.C. N.O.

ZONE

2200

Ohm

EOL 8

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL 6

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL 4

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL 2

N.C. N.O.

ZONE

2200

Ohm

EOL

12 Volt

Sealed

Lead Acid

Control needs AC power to start. Momentarily shorting these two pads allows control to startup on battery only.

16.5VAC, 45VA UL Listed Class 2 Transformer - ELK-TRG1640

DO NOT CONNECT TO A SWITCHED OUTLET

For Canada use cUL Listed Transformer - ATC Frost # FPS-4016 18AWG Min.

NEG

N.C. N.O.

ZONE

2200

Ohm

EOL 16

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL 14

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL 12

N.C. N.O.

ZONE

2200

Ohm

EOL

N.C. N.O.

ZONE

2200

Ohm

EOL 10

N.C. N.O.

ZONE

2200

Ohm

EOL

Master Power Switch (SW1), disconnects AC and Battery power from control.

This unit provides Residential fire alarm service when installed according to ANSI/NFPA 72. Transmission

of the fire alarm signal to a fire alarm headquarters or central station shall be permitted only with the

approval of the authority having jurisdiction. The burglar alarm signal shall not be transmitted to a police

emergency number, equipment is to be installed in accordance with NFPA (985,55.1.P).

Recommended locations and wiring methods shall be in accordance with CSA C22.1, Canadian Electrical

Code, Part I, Safety Standard for Electrical Installations; CAN/ULC-S302, Installation and Classification of

Burglar Alarm Systems for Financial and Commercial Premises, Safes and Vaults; and CAN/ULC-S301,

Standard for Central and Monitoring Station Burglar Alarm Systems.

Reference NFPA70 (NEC) & Canadian Electrical Code.

All circuits are current limited except for Battery leads. Refer to Appendix F.

For Installation of Residential Fire Warning Systems reference CAN/ULC-S540 Standard.

Testing of this system should be performed regularly with the primary AC power de-energized. Control

panel specifications are subject to change without notice.

Lithium 3V "Clock" battery, Varta #CR2032 located in upper left corner behind cover. Battery has a life

expectancy of approx. 10 years. Replace ONLY with exact model available at most electronics and camera

retailers. "CAUTION: Lithium Battery May Explode If Mistreated. Do Not Recharge, Disassemble, or

Dispose Of In Fire."

Dialer/Modem is idle. If ON, Dialer/Modem is in use (communicating).

1 blink with equal On and Off times is Normal. 2 fast blinks = Control running on

bootloader only. 4 fast blinks = Control is re-initializing it's EEPROM memory after

a firmware flash. 5 fast blinks = Memory/Operation overflow

Battery is connected correctly. If ON, check battery lead connections.

AC Voltage is present and power switch is turned ON. If OFF, check AC power.

Phone line is good and house phones are connected. If ON constantly, the phone

line may be bad. During remote mode this LED will be ON since the house phones

are then disconnected from the outside line & are being powered from control.

TELCO

SEIZED

DIALER

ACTIVE OFF

OFF

LEDS

Indicators

Power

Regular 1

sec. Blink

Battery

Reversed OFF

Status

4-Wire Smoke Detector

2200

Ohm

EOL

To Zone Input

U.L. Listed EOL Supervision Relay

(ESL #204 or Equivalent).

N.O. Alarm

Contacts

Switched +12 VDC Output

protected by 1.1A PTC.

BATTERY

To Zone NEG

(Left Side Terminals)

Normal

State Descriptions

Color Code for 2200

Ohm EOL Resistor

Part # ELK-ER2200

Color Code for 820

Ohm EOL Resistor

Part # ELK-ER820

NOTE: M1ZTS Temperature Sensors may only be connected to the first 16 zones.

Smoke Detector covers should be kept free

from dust and dirt by use of a dry or damp

(water) cloth as needed. When necessary,

clean the detector interior and/or replace the

optical chamber according to instructions

provided by the Smoke Detector Manufacturer.

2-Wire Smoke Detector

820

Ohm

EOL

NEG

Z16

Compatibility Identifier: M10001

Maximum Operating Voltage: 13.8 VDC

Max. wire resistance should not exceed 13 Ohms.

Use 18AWG Fire approved wire. Max. wire length = 1000 feet.

Do not mix different models on same circuit as proper operation

may be impaired.

Name

System Sensor

Sentrol (GE)

Model

2W-B, 2WT-B, 1151, 2100, 2100T, 2151

429AT, 521BXT, 521B

Compatibility ID

S09A

Max #

Base

None

To configure Zone 16 as a 2-wire smoke zone, set Jumper JP1 to "2 WIRE SMOKE" and use 820

Ohm EOL resistor, part # ELK-ER820.

2-Wire Smoke Detector Compatibility

† †

M1G "Board only" non-alarm

current draw = 140mA ( .14 Amp )

Gray (8)

Red (2)

Brown (1 x 0)

Gold (quality)

Red (2)

Red (2 x 0)

Gold (quality)

Wiring & Hookup Diagram

M1G Installation and Programming Page 7

(Right Side Terminals)

OUT1

+12V (+VAUX)

NEG

NEG -

DATA B

+12V

DATA BUS

J3 J4

1 WAY

PLC

Mode

2 WAY

JP2

RS232

J16

OUT3 LED

OUT3OUT2

+-+-

+VKP

DATA B

DATA A

NEG

Not Used

TIP

RING

* See Auxiliary Current ratings

1 WAY (PL513/PSC04) Select PLC Mode (JP2)

Selects single or bi-directional

PLC Transmissions

2 WAY (TW523/PSC05)

JP2

Voice/Siren †

OUTPUTS

AUDIO NETWORK INTERFACE

Aux Data Bus (J3) ††

For wireless receiver. Presently

works with ITI / Caddx NX408E,

NX416E, or NX448E. See

Programming Menu 14.

Audio Network Connection (J7) ††

For Two-Way Listen-in and Future Use!

J1J2

NEG

+12V

N/CCOMN/O

Compiles with FCC Part 68

Reg. Number: US:5K6AL03BELK-M1

Ringer Equivalence REN: 0.3B

Use USOC RJ-31X connector.

Complies with the limits for class B computer

devices in accordance with the specifications of

subpart J of part 15 of FCC rules.

Out 3 - Programmable General Purpose Relay

Rated at 4Amps @ 12 - 24VDC

(Dry Contacts)

Terminating Jumper (JP3): See

important information about Data

Bus Termination.

This terminal (formerly earth ground) is no longer used. Do not connect this or any neg. terminals to earth ground.

Out 1 - Voice/Siren ††

Speaker output only (Interior)

Out 2 - Connect ONLY 1 UL Listed Bell or Siren (self-contained). For residential Fire the indicating

device shall be Wheelock 34T-12 or equiv. Current limited to 1 Amp. Program Global Option 26 to Voltage.

Speaker(s) are only permitted for non-UL installations and they must be series/parallel wired to avoid

dropping below a 4 ohm total load.

Programmable Outputs (J16)

OUT 7 - 16 are +12V switched

positive general purpose

outputs rated at 50mA.

Lighting ††

Interface Conn.

RJ31X JACK (ELK-RJSET)

PC Personal Computer

(Windows Based)

Serial Port (J4) ††

for Computer/ELKRP

(This connection not

evaluated by UL)

Lighting Interface Conn. (J5) ††

Use Std. 4 conductor modular telephone

cable to connect to a powerline Interface

(PSC05, X-10 PLC or equiv.).

Do not connect to a live phone line!

(This connection not evaluated by UL)

N/C

COM

N/O

DATA BUS TERMINATION IS VERY IMPORTANT!!

Diagram shows 2 basic (4-wire) home run cables with daisy chained devices on each. Last device on each cable

MUST have a Terminating Jumper installed. Jumpers are marked JP2 on keypads, JP1 on Expanders. Control

Hardware pack has two black jumpers for this purpose. Jumpers engage a 120 Ohm resistor across data A & B lines.

NOTE: If there is only 1 data bus cable, install JP3 Jumper on the Control.

Temporary Connection "Plug-in" jacks for RS-485 Data Bus (J1 & J2)

Local connection for Data Bus Devices ie: Keypads, etc. for testing purposes only.

ELK-SP35 or equiv.

PSC05 or

equiv.

Relay Expansion Module (ELK-M1RB)

Optional module adds 8 general purpose

relays. Plugs into J16 connector.

Red

Black

White

Green

Brown

Blue

Yellow

Violet

Pink

Tan

Orange

Grey

+VAUX

NEG

OUT 16

OUT 15

OUT 14

OUT 13

OUT 12

OUT 11

OUT 10

OUT 9

OUT 8

OUT 7

+12V

NEG

Green

Grey

Red

Brown

BLACK

WHITE

GREEN

JP3

RS-485 Data Bus Max. length is 4000 ft. Total

length of 2 homeruns must not exceed that distance.

NOTE: If you want to home run more than 2 cables, run 6 or 8 conductor cable so that the data lines A & B can have a

return path to series connect back out to the next device. This is best done with a ELK-M1DBH Data Bus Hub which

accepts Cat5 or Cat6 cable with RJ45 plugs. For more information see diagram in keypad instructions.

WARNING! The RS485 Data Bus must NEVER have more that two (2) terminating jumpers installed.

RS-485 DATA BUS

DATA A

RED

Data Bus Devices e.g. Keypads, Expanders

Jumper

Terminate

these two

devices.

DO NOT Jumper

Terminate these devices.

Yellow

Green

Red

Black

Yellow

Green

Red

Black

Close up view of std. 4 conductor modular phone cord. When

viewed as shown (back to back), the pin to pin color coding

does not reverse. Cord for PLC must be similar to above.

End

view

Pin 2 < to > 2

Pin 3 < to > 3

Pin 5 < to > 5

Pinout for Serial Port Cable (9 pin male to 9 pin female)

Maximum recommended length = 50 ft.

Out 2 is supervised. If not used, install a 2.2K Ohm

resistor to avoid Output 2 trouble condition.

NOTE: Do Not place a Direct Short Across OUTPUT 2.

Bell (Supervised)

TELCO

LINE

HOUSE

PHONES

Tip

Ring

Green

Red

Yellow

Black

Demark splices

† Not evaluated by UL †† Not for use in UL Listed Systems

Use 26AWG telco wire

A UL Listed Supplementary Power Supply may be required to meet the minimum standby

power supply requirements. Refer to the Chapter containing Regulatory Agency Statements.

Min. wire gauge: 24 AWG

18 to 22 AWG is best for

long distances.

M1G Installation and Programming

Page 8

1.1 Planning the Installation

The first step in any multi-zone security system installation is planning the job.

1. Read this entire manual to familiarize yourself with all system features and procedures before actually beginning the

installation. Read all the information regarding Underwriters Laboratories (UL) and NFPA requirements.

2. Perform a physical survey of the installation site. Use the diagrams below as a guide in planning the installation.

3. Discuss the installation requirements and applications with the customer.

4. Compare the installation requirements and applications with the factory default settings to determine what customized

programming is needed to meet the specific installation requirements.

5. Bench test the system prior to installation.

1.2 Parts Diagram & Descriptions

See Wiring & Hookup Diagram on pages 6 & 7.

1.3 Mounting and Wiring Preparation

Control Mounting

DO NOT MOUNT THE CONTROL OUTDOORS OR IN A DAMP LOCATION OR WHERE THE ENVIRONMENTAL CONDITIONS

ARE UNSUITABLE FOR ELECTRONIC BASED EQUIPMENT. DO NOT MOUNT IN AN UNCONDITIONED ATTIC. USE

COMMON SENSE AND GOOD INSTALLATION PRACTICES. A suitable location would be inside a secure dry location where

the ambient temperature inside the control box can remain at 32‘ to 120°Fahrenheit (0’ to +49' Celsius). Choose a location

that allows easy wiring to an unswitched power outlet and to a grounding conductor for the control. A central location makes

running system wiring easier. Remove control box knockouts that best suit your wiring needs.

After removing all packing materials, compare the system components with those in the figure above to familiarize yourself

with the part names. Mount the control using the upper center slotted hole to level. Install and connect all necessary wiring for

the power transformer, detection loops, keypads and siren outputs.

Keypad Mounting and Wiring

Ideal height is 50-58 inches. Pick a location with an ambient temperature range between 32°and 120°F (0° to +49°C). Avoid

direct sunlight if possible. Fasten backplate to electrical box or wall with flat head screws to prevent shorts to the back of the

circuit board. Keypads have an unpluggable harness for connecting to the M1data bus. Splice the Black, Red, White, and

Green wires from the unpluggable harness to the M1 Data Bus field cabling. Plug the connector into the back of the keypad.

Tuck wires neatly into back plate and install Keypad on mounting plate. The LCD keypads have connections for an optional

programmable output and a programmable zone input. NOTE: Min. field wire gauge is 24 AWG, but 18 to 22 AWG is better for

long distances. CAT5 (8 conductor) cable can be purchased in various wire gauge sizes. Where possible always use the

larger gauge CAT5 cable. The extra conductors in CAT5 wires can be used to provide return path for the data A & B lines.

Section 1 - Installation and Wiring

Legend

- Main Control

- Audible Alarm

- Smoke Detector

- Contact

- Keypad

Bedroom 1Bedroom 2

Bedroom 3 Living Room

Kitchen / Dining

TYPICAL BURGLARY INSTALLATION LAYOUT

Bedroom 1Bedroom 2

Bedroom 3 Living Room

Kitchen / Dining

TYPICAL FIRE INSTALLATION LAYOUT

CCCCC

Basement

First Floor

All perimeter openings below 18" should be provided with protection.

A Smoke Detector shall be located in each sleeping area and between

the sleeping areas and the main living area.

Early warning fire detection is best achieved by the installation of fire

detection equipment in the location shown above.

In homes basements or multiple levels at least one smoke detector

shall be on each level.

M1G Installation and Programming Page 9

1.4 Control Wiring

Zone Inputs (1 thru 16 on main board, 17 thru 208 via expanders)

Zones are arranged in groups of 16, starting with Z1 thru Z16 on the main board. Each 2 zones share a common negative

terminal. A zone may be programming for EOL resistor supervision (Default), or normally closed/normally open without a

resistor. In addition, Burglar and Keyswitch zones may be programmed for EOL with Security Alert on Short, or EOL with

Security Alert on Open/Short, also referred to as a Four (4) State Zone (firmware 4.3.5 or later). If EOL resistors are used, they

should be placed at the furthest most remote end of the detection device wiring. EOL zones permit a combination of N.C.

(normally closed) or N.O. (normally open) devices. Using voltage meter probes across the zone and com terminals, a non-

violated EOL zone will measures approx. 7.0 VDC. An open circuit will be approx. 13.8 VDC. A shorted circuit will be 0

VDC. The Keypad also provides the ability “Menu 8 “System Diagnostics” to view zone voltage.

ELK-M1KP

See Note about

Data Bus

Termination

BLACK

WHITE

GREEN

RED

Keypad

Wiring

Assembly

Optional programmable Zone Input from Keypad

Hookup Diagram for Keypad

Splice 6 Pin Keypad Wiring Assembly to the Data Bus cable using ELK-900-2 "B" Connectors.

BROWN

Optional programmable Output from Keypad

Keypad 1

The optional Zone Input # or Output # is

determined by the Keypad Address.

Load (50mA max)

I.E. LED, Relay

To BLACK (Neg) Wire

To BROWN Wire

N.C. N.O.

2200

Ohm

EOL

To BLACK (Neg) Wire

BLUE

To BLUE Wire

NOTE: Early production M1KP Keypads provided a switched

negative (pull to ground) output. These units have the letter "E"

at the end of the ID number on the lower back side of the board.

Connect per diagram above. Boards marked PC096 with a letter

"F" or later provide the output as a switched positive.

Load (50mA max)

i.e. Relay, LED

To Red (Pos) Wire

To Brown Wire

KP Zone Output

Address # #

1 193 193

2 194 194

3 195 195

4 196 196

5 197 197

6 198 198

7 199 199

8 200 200

KP Zone Output

Address # #

9 201 201

10 202 202

11 203 203

12 204 204

13 205 205

14 206 206

15 207 207

16 208 208

Min. wire gauge: 24 AWG

18 to 22 AWG is best for long

distances.

Optional Four (4) State Zone Wiring (2 series resistors w/ N.C. contacts)

Zone

Input

Neg.

N.C. Alarm

Contacts

2200 Ohm

Resistor

2200 Ohm

EOL Resistor

N.C. Tamper

Contacts

Pos.

Neg.

Fig 2: Powered PIR, Glassbreak, etc. with Tamper

N.C. N.O.

Contact

2200

Ohm

EOL

Zone Input

Neg.

Tamper Contact

N.C.

Alarm

Contact

Diagnostic Table

Short ~

2.2k Ohms

4.4k Ohms

Open ~

0 - 3.9 Volts

4.0 - 7.3 Volts

7.4 - 11 Volts

11.1 - 13.8 Volts

Zone

Resistance

Approx. Zone

Voltage Reading

Alarm

Armed

Sec. Alert/Tamper

Ready

Not Ready

Sec. Alert/Tamper

Disarmed

Condition When:

0 - 72

73 - 159

160 - 220

221 - 255

A to D

Value

Fig 1: N.C. Alarm Contact

(Unpowered) with N.C. Tamper

Program Zone for EOL Wiring

Type 4 - Supervisory on Open

This feature

requires Firmware

2.3.5 or later.

2200 Ohm

Resistor

Traditional Three (3) State Zone Wiring (1 series resistor)

Wire in Series with zone

input or use another zone.

Neg.

N.C. Alarm

Contacts

2200 Ohm

EOL Resistor

N.C. Tamper

Contacts

Pos.

Neg.

Powered Motion, PIR, Glassbreak, etc.

N.O.

Contact

2200

Ohm

EOL

Zone Input

Neg.

N.C.

Alarm

Contact

Diagostic Table

Short ~

2.2k Ohms

Open ~

0 - 3.9 Volts

4.0 - 8.8 Volts

8.9 - 13.8 Volts

Zone

Resistance

Approx. Range

of Zone Voltage

Alarm

Armed

Not Ready

Ready

Not Ready

Disarmed

Condition When:

0 - 72

73 - 170

171 - 255

A to D

Value

Zone

Input

Alarm Contact

NOTE: Refer to the section ‘Data Bus E.O.L. Termination’ for information on multiple homerun cables. NEVER SPLICE OR

CONNECT WIRE WITH CONTROL POWER ON. Minimum cabling should be four conductor 22 or 24 gauge. Maximum resistance per wire

is 25 Ohms. Device placement beyond 1000' is not recommended.

M1G Installation and Programming

Page 10

Two-Wire Smoke Zones (Zone 16)

To enable use of two-wire smoke detectors on Zone 16, position Jumper JP1 (located below Zone 16 terminals) so that the

two right hand pins are covered. Go to Installer programming mode, Menu 05 - Zone Definitions, and program Zone 16 as a

Fire zone (Def=10). Step to next location and program Wire Type=6. NOTE Use only compatible two-wire detectors listed on

the front label of the control. Do not mix brands. The maximum number of detectors is also listed on the front label. For

two-wire operation, a 820 Ohm EOL resistor part # ER820 must be used instead of the 2,200 Ohm resistor part # ER2200.

Use 18AWG Fire approved wire. Max. wire length = 1000 feet. Max. wire resistance should not exceed 13 Ohms.

Switched Power Connection (+SAUX)

Four-wire smoke detector and other devices that require a temporary power disruption in order to reset or unlatch from the

alarm state (i.e. smoke detectors, etc.) should be connected to the +SAUX 12 Volt DC switched power terminal. When a

smoke reset is performed, the operating voltage to these devices is momentarily interrupted.

Auxiliary Power Connections (+VAUX)

Motion detectors, glass breaks, etc. and other devices requiring unswitched 24-hour power should be connected to one of the

auxiliary terminals, +VAUX. All negative terminals on the terminal strip are at the same reference and may be used whenever

a common (circuit ground) negative is required. Use caution when wiring the control to distribute the load devices among the

supply and the negative terminals evenly. NOTE: Circuit ground refers to any negative terminal connection on this control.

This does not refer to the earth ground terminal or to the common terminals of Relay Output 3. These terminals are not at

the same voltage potential and should not be wired so that they are electrically connected to a negative.

PTC (Positive Temperature Coefficient) Circuit Breakers

The +VAUX Auxiliary power and J16 power output terminals are protected against shorts and overloads by a 1.25A PTC. A PTC

is a solid state, auto-restoring type of circuit breaker. The +SAUX Switched (Smoke) power output is protected by a 1.1A PTC.

The +VKP Keypad power output is protected by a 1.25A PTC. Output 2 is protected by a 1.25A PTC. NOTE: Sometimes it may

be necessary to remove power (unplug the outputs) for approx. 20 seconds after a short, to allow the PTC to reset. Even

if the short is no longer present, the remaining residual current draw may be so high that the PTC cannot determine that

the short is gone. If the PTC re-trips, check the field wiring and repair.

Transformer Primary Power Input (AC)

The control is powered by a 16.5 VAC, 40 min. VA, UL Listed Class 2 transformer (ELK-TRG1640). The specified sized and

rated transformer must be used to operate this control. The transformer must be connected to a 120 VAC, 24-hour outlet not

controlled by a switch other than an approved overcurrent protection device.

Connect the transformer to the AC Terminals using 16 to 18 gauge minimun wire. Do not exceed 50 feet between the

transformer and the control or run the AC power in a multiconductor with other system circuits. Leave the transformer

unplugged as well as the standby battery until all other connections have been made.

Standby Battery Connection

Connect the BLACK wire to the Neg (-) terminal on the battery, the connect the RED wire to the Pos (+) terminal on the battery.

The control is designed to operate with and recharge a 12 volt, sealed lead acid battery from 7Ah up to 18 Ah for backup of the

primary power supply. The control maintains a float charge for the battery of 13.8 VDC at 100 mA. This is in addition to the

continuous output of 1.5 Amps that the power supply maintains (see maximum current drains for UL Listed Systems).

CAUTION: Do not reverse the battery leads! The control has special circuitry which helps protect it from battery reversal

damage for short durations. However, prolonged reversal of the battery leads may cause permanent damage. A reverse

battery warning LED is located to the left of the power On/Off switch. If this light is ON, turn the power off immediately

and correct the battery lead connections.

+VAUX

NEG

SW1

16.5 V

JUMPER TO START

WITH NO AC

POWER

BATTERY

12V Battery

5 to 18Ah

Sealed Lead Acid

STATUS

REVERSE

BAT LEADS

UL Listed Transformer,

Class 2, 16.5VAC, 45VA

RED BLK

ELK-TRG1640

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elk Products Bedienfeld Handbücher

Elk Products

Elk Products EZ8 ELK-M1EZ8 Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten