Elk Products EZ8 ELK-M1EZ8 Bedienungsanleitung

INSTALLATION

MANUAL

Cross Platform Control

Part # ELK-M1EZ8

A member of the M1 Family

Specifications, Installation and Programming

M1 includes the SIA CP-01 Standards for False Alarm Reduction †

L523 Rev. I 08/06/08 Current with Firmware 4.5.4

M1EZ8InstallationandProgramming

Page2

Introduction

LIMITATION

This Control is designed to warn against unauthorized entry and other situations. However, it is not a guarantee of protection against the

occurrence of burglary, fire, or other emergency. Any alarm system is subject to compromise or failure to warn for various reasons. For

example:

- Unauthorizedaccesscanbegained through unprotectedpoints or bydisarming or bypassingprotected points.

- Sensingdevices are powerdriven and do not operate without electrical power. Battery-operateddevices will notwork without batteries,with

deadbatteries, or ifthe batteries arenot put inproperly. Devices powered solely byACwill not workif theirAC power supply is cut offfor any

reason, however briefly.

- Telephone linesover which alarmsignals are transmittedmay be outof service or rendered inoperable by an intruder.

- Even if the system respondsto the emergency as intended, occupants may haveinsufficient time to protect themselves from the emergency

situation.In thecase of a monitored alarmsystem, authoritiesmay not respond appropriately.

- Smokedetectors have limitationsand cannot detect all types of fires. Accordingto data publishedby the Federal Emergency Management

Agency,whilesmoke detectorshave playeda keyrole inreducing residentialfire deathsin theUnited States,they maynot activateor provide

early warning for a variety of reasons in as many as 35% of all fires, . Some of the reasons some detectors used in conjunction with this

System may not work areas follows. Smoke detectors may have been improperly installedand positioned. Smoke detectors may not sense

fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke

detectorsalso maynot sensea fireon anotherlevel ofa residence or building.Asecond floordetector,for example,may not sense afirst floor

or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general,

detectorsmay notalways warnabout firescaused bycarelessness andsafety hazardslike smokingin bed,violent explosions,escaping gas,

improperstorageof flammablematerials,overloaded electrical circuits,children playing withmatches,or arson.Dependingan thenatureof the

fire, and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all

occupantsto escape in time to prevent injury or death..

- Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path

has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.

- Wirelesstransmitters (used insome systems) aredesigned to providelong battery lifeunder normal operatingconditions. Longevity of

batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External

factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given

installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of battery to

maintainprotection for thatgiven point withinthe system.

- Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance.

Homeowner, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and

property.

- Auser may not be able to reach a panic or emergency button quickly enough.

- PassiveInfrared Motion Detectorscan only detectintrusion within thedesigned ranges asdiagrammed in their installation manual. Passive

InfraredDetectors donot providevolumetric areaprotection. Theydo create multiple beams of protection, and intrusion canonly bedetected

inunobstructed areas covered by thosebeams. They cannotdetect motion or intrusion thattakes place behind walls, ceilings,floors,closed

doors,glass partitions,glass doors, orwindows. Mechanicaltampering, masking,painting or spraying of anymaterial onthe mirrors,windows

orany partof the optical system can reduce their detection ability.Passive InfraredDetectors sensechanges intemperature; however,as the

ambient temperature of the protected area approaches the temperature range of 90 to 105F (32 to 40C), the detection performance can

decrease.

- Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of

closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, they are less likely to

waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a

stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-

impairedpeople.

- This equipment, like other electrical devices, is subjectto component failure. Even though this equipment is designed to last as long as 20

years,the electronic componentscould fail at any time.

- The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm

system should be tested weekly to make sure all sensors and transmitters are working properly.

Nopart of thispublication may be reproduced, storedin a retrieval system, or transmitted in anyform or by any means, electronic, mechanical,

photocopying,recording, orotherwise without the prior writtenpermission ofthe manufacturer.The material in this publicationis forinformation

purposesand subjectto change without notice. Themanufacturer assumesno responsibilityfor anyerrors which mayappear inthis publication.

PrintedinU.S.A.

Use of this control forfire detection and/or annunciation may not be permittedby certain states, counties, municipalities or local jurisdiction. Itis

the responsibility of theinstalling alarm company to check withthe localA.H.J. (Authority Having Jurisdiction) orState Fire Marshal’sofficeprior

to using this control for fire detection.

M1EZ8InstallationandProgramming Page3

Table of Contents

Specifications, Features, and Benefits ..................................................................................................... 4

Wiring & Hookup Diagram........................................................................................................................... 5

Section 1 - Installation and Wiring ............................................................................................................. 7

1.1PlanningtheInstallation ...................................................................................................................... 7

1.2 Parts Diagram & Descriptions ........................................................................................................... 7

1.3 Mounting and Wiring Preparation ....................................................................................................... 7

1.4 Control Wiring .................................................................................................................................... 8

Data Bus E.O.L. Termination - VERY IMPORTANT! ...............................................................................11

Section 2 - Operating the System ............................................................................................................ 13

2.1 Introduction ....................................................................................................................................... 13

2.2 Powering Up (One Keypad)............................................................................................................. 13

2.3 User Codes andAuthorities.............................................................................................................. 13

2.4 Installer Program Code andAuthorities ............................................................................................ 13

2.5 Keypad Overview ............................................................................................................................. 14

KeypadMenus........................................................................................................................................ 15

Menu 0 - Select KeypadAlternateArea - Multi-area (Partition) Operation.............................................. 18

Section 3 - Programming The Control..................................................................................................... 19

3.1 Introduction ....................................................................................................................................... 19

3.2 Local Keypad Programming............................................................................................................. 19

3.3 Local or Remote Computer Programming (ELK-RP) and Anti-Takeover ......................................... 19

3.4Area Partitioning................................................................................................................................ 19

3.5 Communicator Setup Checklist ....................................................................................................... 20

3.6 Entering Installer Level Programming............................................................................................... 20

Menu 01 - Bus Module Enrollment.......................................................................................................... 22

Menu 02 - User Code Options................................................................................................................ 23

Menu 03 -Area Definitions...................................................................................................................... 24

Menu 04 - Keypad Definitions................................................................................................................. 26

Menu 05 - Zone Definitions ..................................................................................................................... 28

Menu 06 -Alarm Duration Timers........................................................................................................... 31

Menu 07 - Global System Definitions ..................................................................................................... 32

Menu 08 - TelephoneAccount Setup ...................................................................................................... 36

Menu 09 -Area Reporting Codes ........................................................................................................... 38

Menu 10 - Zone Reporting Codes........................................................................................................... 40

Menu 11 - Keypad F-Key Reporting Codes ............................................................................................ 41

Menu 12 - Sys Report Code Options & Codes ...................................................................................... 42

Menu 13 - User Report Codes................................................................................................................ 44

Menu 14 - Wireless Definitions............................................................................................................... 45

Section 4 - PC Programming and Automation Capabilities.................................................................... 47

4.1 ELK-RP Software............................................................................................................................ 47

4.2 Update/Verify Firmware in the Control and Peripherals ................................................................... 48

4.3 Automation Rules andAttributes...................................................................................................... 49

Appendix A - Event Codes ........................................................................................................................ 56

Appendix B & C - Unused ......................................................................................................................... 58

Appendix D - Two Way “Listen-in/Talk” Interface................................................................................... 60

Appendix E - SIA CP-01 Compliance ........................................................................................................ 61

Appendix G - Additional ELK-M1KP Keypad Information ...................................................................... 65

Index............................................................................................................................. 67

M1EZ8InstallationandProgramming

Page4

† Not evaluated by UL †† Not for use in UL Listed Systems

General:

• Large zone capacity: 8 on-board zones expandable to 200

• Wireless capability: †Up to 48 zones

• Two Way Listen-in interface †

• Flash Memory - Allows field updates to firmware electronically

• Time/Date stamped 512 event history log

• Menu driven, text keypad programming

• 12 On-Board Outputs: 1 siren driver/voltage, 1 form “C” Relay,

and 10 low current (10 mA) voltage outputs

• TotalNumberofOutputsSupported:204

• Supports 4 wire (any zone) and 2 wire (zone 8) smoke

detectors

• Includes Fire alarm verification routine

• Can be partitioned into 8 areas and account numbers

• User Codes: 199 (4 or 6 digit) with assignable authority

levels

• Arm levels:Away, Stay, Stay Instant, Nite, Nite Instant, Vacation

• Hardware "watchdog" and nonvolatile EEPROM memory

• Supervised phone line and alarm output

• Connection for optional ELK-MSI RS-232 serial port 0 to

interface PCs and peripheral devices

• Total serial ports with expansion: 8

Communications

• True V.22 bis Modem for fast reliable upload/download

• Phone Number Capacity: 8

• Optional Ethernet †int. for reporting, operation, programming

• Communicator formats: SIA, Contact ID, 4 + 2, and Pager

• Elk-RP PC programming software with conflict resolution to

easily highlight differences between control and PC

- Connect via Dial-up, Optional RS232 port, or Opt. Ethernet

- Automatic answering machine bypass

Keypad

• Backlit, Large Character LCD Display, 16 x 2 lines

• Built-in Temperature Sensor

• Optional Plug-in Prox Access reader (26 bit Weigand format)

• Menu navigation keys and 6 programmable function keys

• Plug-in connector, only 4 wires to the control

• 1 Zone input and 1 Output Programmable per Keypad

• Programmable display of time, date, & temperature

• Displays system diagnostics and settings.

• Maximum Keypads allowed: 16

Automation& Integration

• Create lifestyle enhancing comfort, convenience, and security

• Powerful “Whenever/And/Then” RULES Programming allows

almost any imaginable operation. No need to chain rules

together. Any single “Whenever” event can have one or more

ANDs and THENs (conditions and commands).

• Total number of Rules Supported: 528

• Rules utilize easy to understand text based references

• Control lighting using RS-232 serial or 2-way Power Line

Control (PLC) ports including On, Off, Dim,All On, All Off com-

mands †

• Transmit and receive custom serial ASCII strings

• Read Temperature Sensors - Communicate with Thermostats

• Total thermostats supported: 16

•Sunset/Sunrise calculation and activation built-in

• AdvancedLightingOptions(Pre-setDim,Extended,Levels,

Scenes)

PowerSupply

• Heavy duty - 2.5Amp power supply

• Dynamic battery test

• PTC (fuseless) resettable overload protection

Part Numbers and Accessories:

ELK-M1EZ8CB Control “Board only” †

ELK-M1EZ8 Control in 12 x 12” metal can (Base Unit) †

ELK-M1EZ8KB Control KIT: Board, 12 x 12” can, Xfmr, M1KP

Keypad, 5Ah Battery, SP35 Speaker, & RJSET †

ELK-M1EZ8K Control KIT - NO METAL CAN (for structured

wiring systems) Includes Board,XFMR,M1KP

Keypad, 5Ah Battery, SP35 Spkr, & RJSET †

Utilizes most ELK-M1 Accessories

ELK-M1KP Lg. Keypad, LCD (Green),16 character x 2 lines

ELK-M1KPB Lg. Keypad, LCD (Blue),16 character x 2 lines

ELK-M1KP2 Small Keypad LCD (Blue), 16 char. x 2 lines †

(no internal temp sensor and 2 less “F” keys)

ELK-M1KP3 * same as M1KP2 but with flip down door †

ELK-M1XIN 16 Zone (input) expander

ELK-M1XOVR 16 Output expander, 8 Voltage/8 Relays

ELK-M1XOV 16 Output expander, Voltage only

ELK-M1RB Relay board, 8 form ”C” relays

ELK-M1DBH Data bus wiring hub †

ELK-M1DBHR Data bus wiring hub “Active” for Retrofit †

ELK-M1XEP Ethernet Port Exp/Interface (Qtr 2 of 05) †

ELK-M1XRF2G Wireless Receiver for GE Crystal Xmtrs †

ELK-M1XSP Lighting, Thermostat Interface & Serial exp. †

ELK-M1PR Mini prox reader for keypad †

ELK-M1EZ8TWI Two Way Listen-in Int. w/3 mic inputs †

ELK-M1EZ8MSI Main Serial Interface, supplies RS232 Port 0 †

ELK-M1TWS Speaker & Mic for Two Way Listen-in †

ELK-M1ZTS Zone Temperature Sensor -50 to 140 F †

ELK-RP PC software - Free upon request with

Control Panel purchase

ELK-RM Remote “User” Management software

ELK-TS07 7.25” Color Touchscreen †

Specifications, Features, and Benefits

NOTE: Use of Two Way Listen-in may be regulated by local or

state laws and/or ordinance. It is the responsibility of the

Installer to check before using this feature.

M1EZ8InstallationandProgramming Page5

Wiring & Hookup Diagram

STATUS

LINE SEIZE

N.C.

N.O.

2200

Ohm

EOL

N.C.

N.O.

Zone

2200

Ohm

EOL

POWER

Data Bus-See Note in Manual

RED

BLACK

WHITE

GREEN

Keypad

See Manual

Do Not Connect

to a Phone Line!

JP1

2WIRE

SMOKE NORMAL

ZONE 8

JP3

Lighting Interface

or M1EZ8MSI Main

Serial Port Interface ††

Aux Data Bus (J3) ††

For wireless receiver. Presently

works with GE-Caddx NX408E,

NX416E, or NX448E

Two-Way

Listen-In (J7) ††

Connects to

(M1EZ8TWI)

TELCO

Line

House

Phones

T1 R1

RJ31X Jack

(ELK-RJSET)

8 1

Demark

Block

splices

Yellow

BlackRedGreen

Green Red Brown

PHONE LINE HOUSE LINE

TIP RING T1 R1

Z7NEGZ8

Compiles with FCC Part 68

Reg. Number: US:5K6AL03BELK-M1

Ringer Equivalence REN: 0.3B

Use USOC RJ-31X connector.

Complies with the limits for class B computer

devices in accordance with the specifications

of subpart J of part 15 of FCC rules.

Out 3 - Relay Programmable

General Purpose Dry Contacts

rated: 4 Amps @ 12 - 24VDC

Select PLC Mode (JP2)

Selects single or bi-directional

PLC Transmissions

Terminating Jumper (JP3)

See manual for important

information about Data Bus

Termination.

12Volt - 5Ah min.

See UL requirements

for sizes and standby

times. Test regularly

with ELK-BLT Battery

Life Tester. Replace

every 3-5 years

16V XFMR

AC AC A B

+12V

KP NEG OUTPUT 3

N/O N/CCOM

Line Seize LED is ON if Dialer

is in use (communicating)

Status LED:1 blink = Normal Operation.

2 fast blinks = Bootloader mode.

4 fast blinks = Initializing EEPROM memory.

5 fast blinks = Memory/Operation overflow.

Power LED is ON when AC is present.

Auxiliary +12VDC

Power Output

Protected by 1.25A PTC.

2200 Ohm EOL Resistors are part # ELK-ER2200

ELK-M1EZ8

2 WAY

1 WAY

-X10-

JP2

+12VDC Switched

Smoke Power

1.1 Amp PTC protected

4-Wire Smoke Detector

2200

Ohm

EOL

To Zone Input

U.L. Listed EOL Supervision Relay

(ESL #204 or Equivalent).

(shown energized, contacts closed)

N.O. Alarm

Contacts

To Zone NEG

+VAUX +VSMK

Grey

Ring Tip

T1 R1

Programmable Outputs (J16)

OUT 7 thru 16 are +12V switched positive voltage

outputs rated at 10mA max. Connect optional ELK-

M1RB Relay Board for 8 general purpose relays.

J16

OUT 16

OUT 15

OUT 14

OUT 13

OUT 12

OUT 11

OUT 10

OUT 9

OUT 8

OUT 7

+12V

NEG Red

Black

White

Green

Brown

Blue

Yellow

Violet

Pink

Tan

Orange

Grey

+ALARM -

OUTPUT 2

NEG

Connector J5 acceptseither a 4conductor modular cablefor a PSC05PLC

Lighting Interface OR an8 conductor modular cablefor a EZ8MSI Main Serial Port

Interface w/PSC05passthroughconnector. (ThisconnectionnotevaluatedbyUL)

PSC05 ††

or equiv.

PSC05 or

Equivalent

Computer, OEM

component, etc.

RS-232

ELK-M1EZ8MSI

Main Serial Port Interface

RS232

Serial

Cable

4 Conductor

Modular Cable

8Conductor

ModularCable

From

EZ8

Powerline

Interface

To J5

Connector

4Conductor

ModularCable

BATTERY

RED BLK

Zone

(Sold separately)

12V

Battery

Yellow

Green

Red

Black

4conductormodular(standard)phone

cordforPLCLighting(not supplied).

End view

Yellow

Green

Red

Black

8 Conductor Cat5 cable from EZ8MSI Main SerialPort Interface.

End view

Brn/Wht

Wht/Brn

Grn/Wht

Wht/Blue

Blue/Wht

Wht/Grn

Org/Wht

Wht/Org

Org/Wht

Wht/Grn

Blue/Wht

Wht/Blue

Grn/Wht

Wht/Brn

Brn/Wht

110806

ELK

PRODUCTS, INC.

HILDEBRAN, N.C., 28637, USA

NOTE: Refer to Appendix F in the Installation Manual

#L523 Rev. I05/07 for the UL limitations on total

continuous 'standby' current drain from terminals

+VAUX, +12VKP, +VSMK, and J16. N.C.

N.O.

2200

Ohm

EOL

N.C.

N.O.

Zone

2200

Ohm

EOL

Z5NEG

Zone

N.C.

N.O.

2200

Ohm

EOL

N.C.

N.O.

Zone

2200

Ohm

EOL

Z3NEGZ4

Zone

N.C.

N.O.

2200

Ohm

EOL

N.C.

N.O.

Zone

2200

Ohm

EOL

Z1NEG

Zone

RS232 Serial Port Cable (9 pinmale

to 9 pin female) Max. length = 50 ft.

Pin 2 < to > 2

Pin 3 < to > 3

Pin 5 < to > 5

Sealed Lead Acid Battery (ELK-1250)

Note: Secondary phone line surge

suppression devices (ELK-950) are

recommended for areas prone to transient

or lightning strikes.

2-Wire Smoke Detector

820

Ohm

EOL

NEG

Compatibility Identifier: M10001

Maximum Operating Voltage: 13.8 VDC

Max. wire resistance should not exceed 13 Ohms.

Use 18AWG Fire approved wire. Max. wire length = 1000 feet.

Do not mixdifferent models on same circuit as proper operation may be impaired.

Name

System Sensor

Sentrol (GE)

Model

2W-B, 2WT-B, 1151, 2100, 2100T, 2151

429AT, 521BXT, 521B

Compatibility ID

S09A

Max #

Base

None

To configure Zone 16 as a 2-wire smoke zone, set Jumper JP1 to "2 WIRE

SMOKE" and use 820 Ohm EOL resistor, part # ELK-ER820.

2-Wire Smoke Detector Compatibility

† †

16.5VAC, 45VA

ELK-TRG1640)

Do not connect to

switched outlet.

UL Listed Class 2 Transformer

For Canada use cUL Listed

Transformer - ATC Frost #FPS-4016

This unit provides Residential fire alarm service when installed according to

ANSI/NFPA 72. Transmission of the fire alarm signal to a fire alarm

headquarters or central station shall be permitted only with the approval of the

authority having jurisdiction. The burglar alarm signal shall not be transmitted

to a police emergency number, equipment is to be installed in accordance with

NFPA (985,55.1.P). Reference NFPA70 (NEC) & Canadian Electrical Code.

All circuits are current limited except for Battery leads. Refer to Appendix F.

Testing of system should be performed regularly with the primary AC power

de-energized. Control specifications are subject to change without notice.

For Installation of Residential Fire Warning Systems reference CAN/ULC-S540

Standard.

Smoke Detector covers should be kept free from dust and dirt by use of a dry

or damp (water) cloth as needed. When necessary, clean the detector interior

and/or replace the optical chamber according to instructions provided bythe

Smoke Detector Manufacturer.

M1EZ8 "Board only" non-alarm current draw = 140mA ( .14 Amp )

Out 2 - Alarm Connect ONLY 1

UL Listed Bell or Siren (self-

contained). For residential Fire

the indication device shall be

Wheelock 34T-12 or equiv.

Current limited to 1 Amp.

Program Global Option 26 to

Voltage. Speakers are only

permitted for non-UL installations

and must be series parallel wired

to avoid dropping below a 4 ohm

total load.

† Not evaluated by UL †† Not for use in UL Listed Systems

††

Use 26AWG

Telco wire

M1EZ8InstallationandProgramming

Page6

IntentionallyLeftBlank

M1EZ8InstallationandProgramming Page7

1.1 Planning the Installation

The first step in any multi-zone security system installation is planning the job.

1. Read this entire manual to familiarize yourself with all system features and procedures before actually beginning the

installation. Read all the information regarding Underwriters Laboratories (UL) and NFPA requirements.

2. Perform a physical survey of the installation site. Use the diagrams below as a guide in planning the installation.

3. Discuss the installation requirements and applications with the customer.

4. Compare the installation requirements and applications with the factory default settings to determine what customized

programming is needed to meet the specific installation requirements.

5. Bench test the system prior to installation.

1.2 Parts Diagram & Descriptions

See Wiring & Hookup Diagram on pages 6 & 7.

1.3 Mounting and Wiring Preparation

Control Mounting

DO NOT MOUNTTHE CONTROLOUTDOORS OR INADAMP LOCATION OR WHERE THE ENVIRONMENTAL CONDITIONS

ARE UNSUITABLE FOR ELECTRONIC BASED EQUIPMENT. DO NOT MOUNTINAN UNCONDITIONEDATTIC. USE

COMMON SENSE AND GOOD INSTALLATION PRACTICES. A suitable location would be inside a secure dry location where

the ambient temperature inside the control box can remain at 32‘ to 120°Fahrenheit (0’ to +49' Celsius). Choose a location

that allows easy wiring to an unswitched power outlet and to a grounding conductor for the control. A central location makes

running system wiring easier. Remove control box knockouts that best suit your wiring needs.

After removing all packing materials, compare the system components with those in the figure above to familiarize yourself

with the part names. Mount the control using the upper center slotted hole to level. Install and connect all necessary wiring for

the power transformer, detection loops, keypads and siren outputs.

Keypad Mounting and Wiring

Ideal keypad height is 50-58 inches above the floor. Select a location with an ambient temperature range between 32°and

120°F (0° to +49°C). Avoid direct sunlight if possible. Fasten mounting plate to electrical box (or directly to wall) using flat

head screws to prevent shorts to the back of the circuit board. Keypads have a removable wiring plug for connecting to the M1

4-wire data bus. CAT5 or CAT6 eight (8) conductor cable is recommended for all Data Bus cables. The extra wires provide

data return paths. Splice the Black, Red, White, and Green wires from the removable wiring plug to the Data Bus cable. Plug

the connector into the back of the keypad. Tuck wires neatly into back plate and install Keypad on mounting plate. Each

keypad has connections for an optional programmable output and a programmable zone input.

Section 1 - Installation and Wiring

Legend

- Main Control

- Audible Alarm

- Smoke Detector

- Contact

- Keypad

Bedroom 1Bedroom 2

Bedroom 3 Living Room

Kitchen / Dining

TYPICAL BURGLARY INSTALLATION LAYOUT

Bedroom 1Bedroom 2

Bedroom 3 Living Room

Kitchen / Dining

TYPICAL FIRE INSTALLATION LAYOUT

CCCCC

Basement

First Floor

All perimeter openings below 18" should be provided with protection.

A Smoke Detector shall be located in each sleeping area and between

the sleeping areas and the main living area.

Early warning fire detection is best achieved by the installation of fire

detection equipment in the location shown above.

In homes basements or multiple levels at least one smoke detector

shall be on each level.

M1EZ8InstallationandProgramming

Page8

1.4 Control Wiring

Zone Inputs (1 thru 8 on main board, 17 thru 208 via expanders)

Zones Z1 thru Z8 are on the main board, others are in groups of 16, starting with Z17. Each 2 zones share a common

negative terminal. A zone may be programming for EOL resistor supervision (Default), or normally closed/normally open

without a resistor. In addition, Burglar and Keyswitch zones may be programmed for EOL with Security Alert on Short, or EOL

with Security Alert on Open/Short, also referred to as a Four (4) State Zone (firmware 4.3.5 or later). If EOL resistors are used,

they should be placed at the furthest most remote end of the detection device wiring. EOL zones permit a combination of

N.C. (normally closed) or N.O. (normally open) devices. Using voltage meter probes across the zone and com terminals, a

non-violated EOL zone will measures approx. 7.0 VDC. An open circuit will be approx. 13.8 VDC. A shorted circuit will be

0 VDC. The Keypad also provides the ability “Menu 8 “System Diagnostics” to view zone voltage.

ELK-M1KP

See Note about

DataBus

Termination

BLACK

WHITE

GREEN

RED

Keypad

Wiring

Assembly

DataBus Cable

CAT5 or CAT6 Recommended

Optional programmable Zone Inputfrom Keypad

Hookup Diagram for Keypad

Splice 6 Pin Keypad Wiring Assembly to the Data Bus cable using ELK-900-2 "B" Connectors.

BROWN

Optional programmable Output from Keypad

Keypad 1

The optional Zone Input # or Output# is

determined bythe Keypad Address.

Load (50mA max)

I.E. LED, Relay

To BLACK (Neg) Wire

To BROWN Wire

N.C. N.O. 2200

Ohm

EOL

To BLACK (Neg) Wire

BLUE

To BLUE Wire

NOTE: The first batchof M1KP Keypads provided aswitched

negative (pull to ground) output. Connect per diagram above.

These units have the letter"E" at the end of the ID number onthe

lower back side of the board. EG:PC096EBoards with a letter

"F" or later provide the output as a switched positive.

Load (50mA max)

i.e. Relay, LED

To Red (Pos) Wire

To Brown Wire

KP Zone Output

Address # #

1 193 193

2 194 194

3 195 195

4 196 196

5 197 197

6 198 198

7 199 199

8 200 200

KP Zone Output

Address # #

9 201 201

10 202 202

11 203 203

12 204 204

13 205 205

14 206 206

15 207 207

16 208 208

Optional Four (4) State Zone Wiring (2 series resistors w/ N.C. contacts)

Zone

Input

Neg.

N.C. Alarm

Contacts 2200 Ohm

Resistor

2200 Ohm

EOL Resistor

N.C. Tamper

Contacts

Pos.

Neg.

Fig 2: Powered PIR, Glassbreak, etc. with Tamper

N.C. N.O.

Contact

2200

Ohm

EOL

Zone Input

Neg.

Tamper Contact

N.C.

Alarm

Contact

Diagnostic Table

Short ~

2.2k Ohms

4.4k Ohms

Open ~

0 - 3.9 Volts

4.0 - 7.3 Volts

7.4 - 11 Volts

11.1 - 13.8 Volts

Zone

Resistance Approx. Zone

Voltage Reading Alarm

Alarm

Armed

Sec. Alert/Tamper

Ready

Not Ready

Sec. Alert/Tamper

Disarmed

Condition When:

0 - 72

73 - 159

160 - 220

221 - 255

A to D

Value

Fig 1: N.C. Alarm Contact

(Unpowered) with N.C. Tamper

Program Zone for EOL Wiring

Type 4 - Supervisory on Open

This feature

requires Firmware

2.3.5 or later.

2200 Ohm

Resistor

Traditional Three (3) State Zone Wiring (1 series resistor)

Wire in Series with zone

input or use another zone.

Neg.

N.C. Alarm

Contacts 2200 Ohm

EOL Resistor

N.C. Tamper

Contacts

Pos.

Neg.

Powered Motion, PIR, Glassbreak, etc.

N.O.

Contact

2200

Ohm

EOL

Zone Input

Neg.

N.C.

Alarm

Contact

Diagostic Table

Short ~

2.2k Ohms

Open ~

0 - 3.9 Volts

4.0 - 8.8 Volts

8.9 - 13.8 Volts

Zone

Resistance Approx. Range

of Zone Voltage Alarm

Alarm

Armed

Not Ready

Ready

Not Ready

Disarmed

Condition When:

0 - 72

73 - 170

171 - 255

A to D

Value

Zone

Input

Alarm Contact

NOTE: Refer to the section ‘Data Bus E.O.L. Termination’ for information on multiple homerun cables. NEVER SPLICE OR

CONNECT WIRE WITH CONTROL POWER ON. Minimum cabling should be four conductor 22 or 24 gauge. Maximum resistance per wire

is 25 Ohms. Device placement beyond 1000' is not recommended.

M1EZ8InstallationandProgramming Page9

Two-Wire Smoke Zone (Zone 8)

To enable use of two-wire smoke detectors position Jumper JP1 to the 2 wire smoke position. Go to Installer programming

mode, Menu 05 - Zone Definitions, and program Zone 8 as a Fire zone (Def=10). Step to next location and program Wire

Type=6. NOTE Use only compatible two-wire detectors listed on the front label of the control. Do not mix brands. The

maximum number of detectors is also listed on the front label. For two-wire operation, a 820 Ohm EOL resistor part #

ER820 must be used instead of the 2,200 Ohm resistor part # ER2200. Use 18AWG Fire approved wire. Max. wire length =

1000 feet. Max. wire resistance should not exceed 13 Ohms.

Switched Power Connection (+VSMK)

Four-wire smoke detector and other devices that require a temporary power disruption in order to reset or unlatch from the

alarm state (i.e. smoke detectors, etc.) should be connected to the +VSMK 12 Volt DC switched power terminal. When a

smoke reset is performed, the operating voltage to these devices is momentarily interrupted.

Auxiliary Power Connections (+VAUX)

Motion detectors, glass breaks, etc. and other devices requiring unswitched 24-hour power should be connected to one of the

auxiliary terminals, +VAUX. All negative terminals on the terminal strip are at the same reference and may be used whenever

a common (circuit ground) negative is required. Use caution when wiring the control to distribute the load devices among the

supply and the negative terminals evenly. NOTE: Circuit ground refers to any negative terminal connection on this control.

This does not refer to the earth ground terminal or to the common terminals of Relay Output 3. These terminals are not at

the same voltage potential and should not be wired so that they are electrically connected to a negative.

PTC (Positive Temperature Coefficient) Circuit Breakers

The +VAUX Auxiliary power and J16 power output terminals are protected against shorts and overloads by a 1.25A PTC. A PTC

is a solid state, auto-restoring type of circuit breaker. The +VSMK Switched (Smoke) power output is protected by a 1.1A PTC.

The +12VKP Keypad power output is protected by a 1.25A PTC. The alarm output is protected by a 1.25A PTC. NOTE:

Sometimes it may be necessary to remove power (unplug the outputs) for approx. 20 seconds after a short, to allow the

PTC to reset. Even if the short is no longer present, the remaining residual current draw may be so high that the PTC

cannot determine that the short is gone. If the PTC re-trips, check the field wiring and repair.

Transformer Primary Power Input (AC)

The control is powered by a 16.5 VAC, 45 min. VA, UL Listed Class 2 transformer (ELK-TRG1640). The specified sized and

rated transformer must be used to operate this control. The transformer must be connected to a 120 VAC, 24-hour outlet not

controlled by a switch other than an approved overcurrent protection device.

Connect the transformer to the AC Terminals using 16 to 18 gauge minimun wire. Do not exceed 50 feet between the

transformer and the control or run the AC power in a multiconductor with other system circuits. Leave the transformer

unplugged as well as the standby battery until all other connections have been made.

Standby Battery Connection

Connect the BLACK wire to the Neg (-) terminal on the battery, the connect the RED wire to the Pos (+) terminal on the battery.

The control is designed to operate with and recharge a 12 volt, sealed lead acid battery from 7Ah up to 18 Ah for backup of the

primary power supply. The control maintains a float charge for the battery of 13.8 VDC at 100 mA. This is in addition to the

continuous output of 1.5 Amps that the power supply maintains (see maximum current drains for UL Listed Systems).

CAUTION: Do not reverse the battery leads! The control has special circuitry which helps protect it from battery reversal

damage for short durations. However, prolonged reversal of the battery leads may cause permanent damage. A reverse

battery warning LED is located to the left of the power On/Off switch. If this light is ON, turn the power off immediately

and correct the battery lead connections.

STATUS

UL Listed Transformer,

Class II, 16.5VAC, 45VA.

i.e ELK-TRG1640

Do not connect to a

switched outlet.

POWER

Sealed Lead Acid Battery

12Volt - 5Ah min. (ELK-1250)

NOTE: See UL requirements for

standby times and battery sizes.

The control is capable of

charging up to an 18Ah battery.

Test battery regularly with

ELK-BLT Battery Life Tester.

Replace every 3-5 years

BATTERY

RED BLK 16V XFMR

AC AC

Status LED:1 blink = Normal Operation.

2 fast blinks = Bootloader mode.

4 fast blinks = Initializing EEPROM memory.

5 fast blinks = Memory/Operation overflow.

Power LED is ON when AC Voltage is present.

12V Battery

M1EZ8InstallationandProgramming

Page10

AC Failure, Low Battery, and Automatic Low Voltage Shutdown

During an AC power failure the battery automatically takes over and AC Fail trouble annunciates at the keypad. The

communicator can be programmed to report AC Fail to the Central Station after a time delay (see Menu 12, System Option 01).

If the battery voltage falls below 11.2 VDC a Low Battery Trouble condition will occur. The communicator can be programmed

to report Low Battery to the Central Station. The battery will continue to run the control until its voltage drops below 10.2 VDC,

at which time the control will disconnect and shut down to prevent a false alarm and damage to the battery. The AC Fail

trouble display will clear if the AC restores. However, the Low Battery Trouble requires a manual or automatic battery load test

before it will clear. An automatic battery load test is performed every 24 hours. See Section 2.2 for powering up the control.

Telephone Line Connection (R1,T1,T,R)

The telephone interface is connected by the use of an approved RJ-31X interconnect jack. This device allows the subscriber

to disconnect the control/communicator from the public switched telephone network in the event of a malfunction. The control

is equipped with line seizure so that the premises telephone service is interrupted during communication to the central

station. Connection to the approved jack is done with a RJSET cord which connects the control terminals to the RJ31X jack.

NOTE: The Telco cord can be supervised to the RJ31X or demarc block by installing an EOL resistor across the Orange and

Blue wires (RJ31X terminals 2 and 7). In the control, connect the Orange and Blue leads to any 24hr Burglar zone input.

Outputs

There are 12 outputs on the main board. In programming these are numbered Out2, Out3, and Out 7 thru 16. The total

outputs may be expanded utilizing output expander boards connected to the RS-485 4-wire Keypad data bus. The Alarm

Output (Out 2) trips when any alarm is activated. All others must be enabled through the RP Rules Programming and can be

triggered by multiple conditions “events”. Do not exceed the current limits on voltage only outputs.

Output 2 - Connect a UL Listed Bell or Siren (self-contained). Current limited to 1 Amp. Program Global Option 26 to Voltage.

This output is supervised. Speaker(s) are only permitted for non-UL installations. Series/parallel wire to avoid dropping

below a 4 ohm total load.

Output 3 is a Single Pole Double Throw Relay with form “C” contacts (Com, N/O, and N/C).

Outputs 7, 8, 9, 10, 11, 12, 13, 14, 15, and 16 are low current, positive (+) voltage only, for driving LEDs, relays, etc. Outputs 4,

5, and 6 ARE NOT available from the main board. They can only be accessed with a data bus Output expander set to

address 1. This expander will replicate main board outputs 7 thru 16, while also including outputs 4, 5, and 6.

Earth Grounding

Tests have determined that the best results against lightning and transients are obtained by isolating the control from ground.

Do NOT connect any of the terminals, especially the Neg. terminals to earth ground. Early production boards had an earth

ground terminal. This terminal is no longer used on circuit board revision I or later. However, ancilliary devices such as the

ELK-950 Surge Protector on the incoming Telephone circuit are still recommended.

Keypad & Expanders on the RS-485 Data Bus (+VKP, Data A, Data B, Neg)

Keypads and data bus expander devices connect to the four terminals marked +VKP, Data A, Data B, and Neg. The keypad

plug-in wire harness color code is: Red +VKP, Green Data A, White Data B, and Black (-) Neg. The +VKP power terminal is

protected by an auto reset PTC device. In the event of a short circuit or malfunction, power will be removed from all devices

until the problem is resolved.

Using Output 7 (low current) with a sensitive relay to switch 24V AC to a Door Strike †

24V AC

Transformer

Door

Strike †

ELK-924 †

POS

NEG

-T+T

N/OCOMN/C

24V OPEN

N/OCOMN/C

+12V

NEG

J16

OUTPUTS

Programmable Outputs (J16) OUT 7 - 16 are +12V switched

positive general purpose outputs rated at 10mA. maximum.

+12V Red

Black

White

Green

Brown

Blue

Yellow

Violet

Pink

Tan

Orange

Grey

+VAUX

NEG

OUT 16

OUT 15

OUT 14

OUT 13

OUT 12

OUT 11

OUT 10

OUT 9

OUT 8

OUT 7

† Not evaluated by UL †† Not for use in UL Listed Systems

Inhaltsverzeichnis

Andere Elk Products Bedienfeld Handbücher

Elk Products

Elk Products ELK-M1G Montageanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung