Elkay SWIRFLO ERPB2-8C Leitfaden

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

97924C (Rev. A - 03/03)

Page 1

SWIRLFLO Refrigerated fountains with FLEXI-GUARD

INSTALLATION, CARE & USE MANUAL

TM TM

CAUTION:

Review these instructions before beginning installation. Be sure that installation

conforms to all plumbing, electrical and other applicable codes.

WARNING:

When installation is complete, ensure these instructions are left in the plastic bag

provided inside the installed unit for future reference.

WARNING:

Service to be performed by authorized service personnel only.

INSTALLER

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices

to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which

results in an electrolysis effect occurring in the fountain. This may result in water which has a metallic

taste to it or has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation. Any

drain fittings provided by the installer should be made of plastic which will electronically isolate the

fountain from the remainder of the buildings plumbing circuits.

ERPB2-8C ERPB2-8RAC

97924C (Rev. A - 03/03)

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

Page 2

LEGEND

A = 1/4 O.D. Tube - Water Outlet Connection

B = 3/8 O.D. Tube - Water Inlet Connection

C = 1-1/4 Waste Tube

D = ELECTRICAL INLET

Figure 1 - Rough-in Dimensions

Model LRPB2-8C Model LRPB2-8RAC

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

97924C (Rev. A - 03/03)

Page 3

Figure 4 - LRPB Tube Routing

1. Install chiller: Remove front panel of chiller. Remove

and discard cardboard inner pack from between

compressor and side panel. Slide chiller onto the

shelf and position it to the left as per dimensions in

Figure 1.

Note: Building construction must allow for

adequate air flow on both sides, top and

back of chiller. A minimum of 4 (102mm) on

both sides and top is required. See chiller

installation for additional instructions.

2. Make water supply connections. Install a shut-off valve

and union connection to building water supply (valve and

union not provided). Turn on water supply and flush the

line thoroughly.

3. ERPB Models: Make connection between remote chiller

and building supply line. Inlet port is marked on the chiller

(1/4 O.D. copper tube). Bend the copper tube (provided)

at an appropriate length from chiller to opening in frame.

Install the in-line strainer (provided with chiller) by pushing

it until it reaches a positive stop, approximately 3/4 (19mm)

on the marked chiller inlet port. Connect building supply

line to strainer. (See Figure 3)

Caution: DO NOT SOLDER tubes inserted

into the strainer as damage to

o-rings may result.

4. LRPB Models: Mount filter head assembly to side of

chiller (See Figure 4). Make connections between filter

and building supply line (3/8 O.D. tube not porvided).

Inlet port is marked on the chiller (1/4 O. D. copper tube).

Install a 1/4 x 1/4 union (provided) on the marked chiller

inlet port. Insert the 1/4 poly tubing (provided) into the

fitting on filter and connect the union to the chiller.

(See Figure 4)

Caution: DO NOT SOLDER tubes inserted

into the strainer as damage to

o-rings may result.

Special Tools

Item Description Quantity

NONE

Additional Materials

Item Description Quantity

1 Unplated copper inlet pipe

2 Service Stop

REQUIRED TOOLS AND MATERIALS

These tables show special tools and/or

additional materials (not provided) which are

necessary to complete installation of these

units:

Figure 2 - Chiller Installation

CHILLER

INLET

CHILLER

OUTLET

TO BUBBLER

Figure 3 - ERPB Tube Routing

TO BUBBLER

25 37

CHILLER

OUTLET WATER

INLET

97924C (Rev. A - 03/03)

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

Page 4

Figure 5 - Upper Panel Installation

Figure 6 - Fountain Installation

Figure 7 - Lower Panel Installation

5. Hang the upper panel on the mounting frame hanger. Be

sure that the panel is engaged with hanger at the top of

frame before releasing it. Align holes in the panel with holes

in the mounting frame. Install two (2) #10-24 x 5/8 (16mm)

screws (Item 29 - Figure 5) in holes and tighten securely.

6. Install the fountain. Remove the screw (Item 30) from cover

plate and slide cover plate (Item 14) toward basin. Mount the

fountain to the upper panel and frame with (4) 5/16 x 1

(25mm) bolts (Item 33), brackets (Item 36) and nuts

(Item 35) provided. Tighten securely. Brackets (Item 36)

must be installed as shown to properly support

fountains. (See Figure 6)

7. Attach waste tube (1-1/4 O.D.) to 1-1/4 O.D. slip

trap (provided by others).

8. ERPB Models: Make connections between remote chiller

outlet tube and fountain. Outlet port is marked on the chiller

(1/4 O.D. copper tube). Install a 1/4 x 1/4 tee (provided)

on the marked chiller outlet port. Insert the 1/4 poly tubing

coming from the fountain into the union. Turn on the water

supply and check for leaks.

CAUTION: DO NOT SOLDER tubes inserted

into the strainer as damage to

o-rings may result.

LRPB Models: Make connections between remote chiller

outlet tube and fountain. Outlet port is marked on the

chiller (1/4 O.D. copper tube). Install a 1/4 x 1/4 tee

(provided) on the marked chiller outlet port. Insert the 1/4

poly tubing coming from the fountain into the union.

CAUTION: DO NOT SOLDER tubes inserted

into the strainer as damage to

o-rings may result.

9. These products are designed to operate on 20-105

PSIG supply line pressure. If inlet pressure is above

105 PSIG, a pressure regulator must be installed in

the supply line.

CAUTION: Any damage caused by connecting

these products to a supply line with

pressure lower than 20 PSIG or

higher than 105 PSIG IS NOT

covered under warranty.

10. Make electrical connections to the chiller. See

chiller instructions.

11. Check stream height from bubbler. Stream height is

factory set at 35 PSI. If supply pressure varies greatly from

this, remove push button (Item 17 - Figure 11) and adjust

the screw on the regulator (Item 19 - Figure 11). To remove

push button, remove set screw from bottom of sleeve

(Item 33). Insert a small punch in screw hole and push up

while grasping the push buttom and pull forward removing

the push button. Clockwise adjustment will raise stream height

and counterclockwise movement will lower stream height. For

best adjustment stream should hit basin approximately 6-1/2

from the bubbler. Reassemble push button by pushing in on

button until the push button catches in the sleeve. Reinstall

the setscrew (Item 33) in the sleeve (Item 15).

12. Mount lower panel. Loosen the three (3) #10-24 x 5/8

(16mm) screws (Item 29 - Figure 6) at frame bottom lip. Slide

upper tongue of lower panel under lower edge of already

installed upper panel. Tighten previously loosened screws

securely. (See Figure 7)

View From Rear

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

97924C (Rev. A - 03/03)

BUBBLER DETAIL

VANDAL RESISTANT BUBBLER DETAIL

NOTE:

When installing replacement bubbler and pedestal, tighten

nut (Item 7) only to hold parts snug in position. Do Not

Overtighten.

Basin

Figure 8 - Bubbler Details

12, 3, 4

Basin

Page 5

97924C (Rev. A - 03/03)

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

Page 6

7 When provided

Figure 9 - Filter Assembly

Water Sentry Filter Detail

DESCRIPTION

ITEM NO. PART NO.

51294C

70792C

70823C

70822C

51299C

70818C

22490C

Filter Head Assy.

Screw #8-18 x .75 PH

Fitting - Superseal 3/8 (10 mm)

Fitting - Superseal 3/8 (6 mm)

Filter Assy

Elbow - 3/8 (10mm)

Bracket

WATER SENTRY® FILTER PARTS LIST

(See Fig. 9)

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

97924C (Rev. A - 03/03)

Page 7

Figure 10 - Fountain Body Assembly

Figure 11 - Push Button Assembly

17 18

23, 38

See Fig. 8

97924C (Rev. A - 03/03)

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC

ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484

Page 8

Figure 12  Water Supply Connections

NOTE: WATER FLOW

DIRECTION SERVICE STOP

(NOT FURNISHED)

BUILDING WATER INLET

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

1/4" O.D. TUBE

WATER INLET

TO COOLER

Installation Package

The components for installation are packed in three

separate boxes, regardless of the type of unit being

installed. The boxes contain the following:

Box No. 1: Wall Frame(s)

Box No. 2: Remote Chiller, ECH8

Box No. 3: Fountain(s), Arm(s) and Panels

Additional materials, as noted in the Parts List, are also

shipped in these boxes.

PARTS LIST

ITEM NO. PART NO. DESCRIPTION

56073C

40319C

50171C

50314C

56011C

55997C

75580C

45392C

100322740560

15009C

55001026

55000944

45767C

28343C

45781C

45792C

45780C

50986C

61313C

15005C

50074C

45769C

40575C

56092C

70682C

55996C

28383C

28384C

27026C

111008343890

70432C

38417001

75560C

75632C

70817C

70020C

28395C

70683C

45805C

Bubbler Assy

Fitting - Orifice

O-Ring

Orifice - Flow Straightener

Housing Assembly

Pedestal

Bubbler Locknut

Body - Bubbler VR

Gasket - Black .68 x 1.03 VR

Nipple - Bubbler VR

Basin - Swirlflow

Lower Shell

Fountain Body

Cover Plate

Sleeve

Pin - Push Button

Push Button

Holder - Regulator

Regulator

Retaining Nut

Gasket - Drain

Assy - Drain/Tailpipe

Assy - Strainer & Ferrule

Poly Tubing (Cut To Length)

Tee - 1/4

Strainer (Provided with Chiller)

Back Panel RH ADA

Back Panel LH ADA

Lower Panel

Screw - #10-24 x .62 HHSM

Screw - #8-32 x .38 THSM

Screw - #8-18 x .37 HHSM

Screw - 5/16-18 x 1.00 HHMS

Setscrew - #10-32 x .38

Fttng - Elbow 1/4 x 1/4

Nut - Hex 5/16-18

Bracket - Support

Fitting - Union 1/4 x 1/4

Adapter

TROUBLESHOOTING & MAINTENANCE

Orifice Assembly: Mineral deposits on

orifice can cause water flow to spurt or not

regulate. Mineral deposits may be removed

from the orifice by poking with a small round

file not over 1/8 diameter, or using a small

diameter wire.

CAUTION:

DO NOT file or cut orifice

material.

Stream Regulator: If orifice is clean,

regulate flow as in Step 11 of the installation

instructions. If replacement is necessary, see

parts list for correct regulator part number.

Actuation of Quick Connect Water

Fittings: Cooler is provided with lead-free

connectors which utilize an o-ring water seal.

To remove tubing from the fitting, relieve water

pressure, push in on the gray collar while

pulling on the tubing. (See Figure 13) To insert

tubing, push tube straight into fitting until it

reaches a positive stop (approximately 3/4).

Figure 13  Quick Connect Fittings

www.DrinkingFountainDoctor.com 800-518-5388

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay LK4430BF1 Bedienungsanleitung

Elkay

Elkay Soft Sides ECDFPW314FPC Installationshandbuch

Elkay

Elkay EDFAC11PBC Installationshandbuch

Elkay

Elkay Soft Sides ERFPD28C Installationshandbuch

Elkay

Elkay ERFP8C*B Installationshandbuch

Elkay

Elkay 4430BF1UFR Series Bedienungsanleitung

Elkay

Elkay EHWM214C*A Installationshandbuch

Elkay

Elkay FLEXI-GUARD DRKR14RC Installationshandbuch

Elkay

Elkay 4420 Series Bedienungsanleitung

Elkay

Elkay LK4420SFRK Bedienungsanleitung

Elkay

Elkay SWIRLFLO ENOBM28K Gebrauchsanweisung

Elkay

Elkay Soft Sides ERO8C-C Installationshandbuch

Elkay

Elkay Space-ette FLEXI-GUARD FDD Installationshandbuch

Elkay

Elkay OFA25 1D Series Installationshandbuch

Elkay

Elkay 4420BFDB Bedienungsanleitung

Elkay

Elkay SWIRLFLO FLEXI-GUARD ezH2O EZWS-EDFPBM117K Gebrauchsanweisung

Elkay

Elkay WGA5 1C Series Installationshandbuch

Elkay

Elkay SWIRLFLO EDFPBWM114C Gebrauchsanweisung

Elkay

Elkay 4460YHHB Series Bedienungsanleitung

Elkay

Elkay FLEXI-GUARD EFW16 1E Series Installationshandbuch

Elkay

Elkay 4400FR Series Bedienungsanleitung

Elkay

Elkay Slimline EHWM14C A Series Bedienungsanleitung

Elkay

Elkay Soft Sides FLEXI-GUARD ERO28C C Series Installationshandbuch

Elkay

Elkay EHFRA7FC*A Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung