Elkay SWIRLFLO EDFPBWM114C Gebrauchsanweisung

Page 1

EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C

97921C (Rev. F - 02/18)

Review these instructions before beginning installation. Be sure that installation

conforms to all plumbing, electrical and other applicable codes.

When installation is complete, ensure these instructions are left in the plastic bag

provided inside the installed unit for future reference.

Service to be performed by authorized service personnel only.

INSTALLER

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices

to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which

results in an “electrolysis” effect occurring in the fountain. This may result in water which has a

metallic taste to it or has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation.

Any drain ttings provided by the installer should be made of plastic which will electronically isolate

the fountain from the remainder of the building’s plumbing circuits.

EDFPB114C EDFPBWM114C

SWIRLFLO®Fountains with FLEXI-GUARD®

INSTALLATION & USE MANUAL

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 297921C (Rev. F - 02/18)

EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C

LEGEND

A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.

B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind

Wall. 1-1/4” O.D. Drain (Trap Not Furnished)

C = Opening For Optional AP-99 Access Panel

Figure 2 - Rough-in Assembly For EDFPB114C

Figure 1 - Rough-in for EDFPB114C W/MP86 Mounting Plate

Optional

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 3

EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C

97921C (Rev. F - 02/18)

28 3/4"

730mm

29 1/4"

743mm

1 1/4"

32mm

FINISHED FLOOR

BACK PANEL

14 1/4"

362mm

OPTIONAL

43 5/8"

1108mm

9 3/4"

248mm

203mm

SURFACE MOUNTING

PLATE

26 1/2"

673mm

16"

406mm

203mm

5 1/4"

133mm 5 1/4"

133mm

3/8" (10mm) DIA. HOLES

FOR MOUNTING PLATE

TO WALL (10)

1/4" (8mm) DIA. HOLES FOR

MOUNTING PLATE TO WALL

7 7/8"

200mm

LEGEND

A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.

B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind

Wall. 1-1/4” O.D. Drain (Trap Not Furnished)

C = Opening For Optional AP-99 Access Panel

NOTE: Reinforce The Wall In The Shaded Areas

Figure 4 - Rough-in Assembly for EDFPBWM114C

Figure 3 - Rough-in for EDFPBWM114C

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 497921C (Rev. F - 02/18)

EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C

27"

686mm

ADA

REQUIREMENT

33 15/16"

862mm

1 5/8"

41mm

5/8"

16mm

18 3/8"

467mm

21 15/16"

557mm

19 3/4"

502mm

FINISHED FLOOR

FINISHED WALL

MPW101 MTG. PLT.

REF. SEPARATE

INSTALLATION

INSTRUCTIONS

FOR DETAILS

Figure 5 -Rough-in EDFPB(V)114C W/MPW101 MOUNTING PLATE

Figure 6 -Rough-in Assembly EDFPB(V)114C W/MPW101 MOUNTING PLATE

LEGEND

A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.

B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind

Wall. 1-1/4” O.D. Drain (Trap Not Furnished)

C = 3/8” (10mm) DIA. Slots For Mounting Hanger Bracket To Wall

28 3/4"

730mm

29 1/4"

743mm

1 7/8"

48mm

16"

406mm

203mm

1 1/4"

32mm

FINISHED FLOOR

BACK PANEL

HANGER BRACKET

MPW101

MTG. PLT.

43 1/2"

1105mm A

27 3/16"

691mm

26 9/16"

675mm

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 5

EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C

97921C (Rev. F - 02/18)

Installation Instructions:

EDFPB114C W/MP86 MTG. PLT.

1. Wall should already be framed for the fountain using

the positioning dimensions shown in Figure 1. Shown

dimensions pertain to installation location (framing

must support up to 300 lbs. weight). These

dimensions are required for compliance with ANSI

Standard A117.0.

2. Install rough-in plumbing as shown in Figure 1. Run

supply water inlet line through the back panel. Install a

service stop (not provided). Turn on supply water and

ush thoroughly.

3. Install fountain. Remove screw (Item 10) from cover

plate and slide cover plate (Item 14) toward basin.

Mount the fountain to the wall and mounting plate with

(4) 5/16” hex nuts (provided with mounting plate).

Tighten securely. (See Figure 7)

4. Determine required length of waste line and cut to

appropriate length. 1-1/4” O.D. waste tube furnished.

1-1/4” slip trap, waste elbow and extension not

provided.

5. Make water supply connections from service stop to

the 3/8” O.D. unplated copper tube coming out of the

strainer. Turn on water supply and check for leaks

(See Figure 17). Newly installed water supply line

should be insulated after leak check is completed.

CAUTION: DO NOT SOLDER tubes inserted

into the strainer as damage to the

o-rings may result.

6. These products are designed to operate on

20-105 PSI supply line pressure. If the inlet

pressure is above 105 PSI, a pressure regulator

must be installed in the supply line. Any damage

caused by reason of connecting these products to

supply line pressures lower than 20 PSI or higher

than 105 PSI is not covered by warranty.

7. Check stream height from bubbler. Stream height is

factory set at 35 PSI. If supply pressure varies

greatly from this, remove push button (Item 3 -

Figure 14) and adjust the screw on the regulator

(Item 18 - Figure 14). To remove push button,

remove setscrew from bottom of sleeve (Item 15).

Insert a small punch in screw hole and push

up while grasping the push button and pull forward

removing the push button. Clockwise adjustment

will raise stream height and counterclockwise

movement will lower stream height. For best

adjustment stream should hit basin approximately

6-1/2” from the bubbler. Reassemble push button

by pushing in on button until the push button

catches in the sleeve. Reinstall the setscrew

(Item 6) in the sleeve (Item 15).

Figure 7 - EDFPB114C Fountain Installation

Figure 8 - AP-99 Panel (Optional)

5/16” Studs - Supplied with MP86

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 697921C (Rev. F - 02/18)

EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C

Figure 9 - Panel Installation

Figure 10 - Fountain Installation

Figure 11 - AP-99 Panel (Optional)

Installation Instructions:

EDFPBWM114C/EDFPB114 W/MPW101 MTG. PLT.

1. Fountains using the MPW Mounting Plate refer to Figure

5 for hanger bracket location and rough-in dimensions.

NOTE: Review separate installation instructions for details of the

MPW Mounting Plate.

Fountains using the Wall Plate Assy. refer to Figure 3

for rough-in dimensions.

2. Shown dimensions pertain to installation location (framing must

support up to 300 lbs. weight). These dimensions are required for

compliance with ANSI Standard A117.0.

3. Install rough-in plumbing as shown in Fig’s. 3 or 5. Run

supply water inlet line through the back panel. Install a service

stop (not provided). Turn on supply water and ush thoroughly.

4. Installing back panel.

Ftn. w/MPW Mounting Plate: Refer to Fig. 16 for placement

of braces onto back panel. Place the upper edge of the panel

above the hanger bracket. Slide the panel down until it engages

the hanger bracket. Be sure back panel is rmly engaged before

releasing it.

Ftn. w/Wall Plate Assy.: Place the upper edge of the panel

above mounting plate on the wall. Slide the panel down until it

engages the mounting plate. Be sure back panel is rmly engaged

before releasing it. (See Figure 9)

5. Install fountain. Remove screw (Item 10) from cover

plate and slide cover plate (Item 14) toward basin. (See Figure 10)

Ftn. w/MPW Mounting Plate: Mount the fountain to the back

panel and wall using (4) 5/16” x 6” long threaded rods, washers,

and nuts (provided). Tighten securely.

Ftn. w/Wall Plate Assy.: Mount the fountain to the back panel

and wall plate assy. with (4) 5/16” x 1” (25mm) long screws

(Item 7 - provided). Tighten securely.

6. Determine required length of waste line and cut to

appropriate length. 1-1/4” O.D. waste tube furnished.

1-1/4” slip trap, waste elbow and extension not provided.

7. Make water supply connections from service stop to the

3/8” O.D. unplated copper tube coming out of the strainer. Turn on

water supply and check for leaks (See Figure 17). Newly installed

water supply line should be insulated after leak check is

completed.

CAUTION: DO NOT SOLDER tubes inserted

into the strainer as damage to the

o-rings may result.

8. These products are designed to operate on 20-105 PSI supply

line pressure. If the inlet pressure is above 105 PSI, a pressure

regulator must be installed in the supply line. Any damage caused

by reason of connecting these products to supply line pressures

lower than 20 PSI or higher than 105 PSI is not covered by

warranty.

9. Check stream height from bubbler. Stream height is factory set at

35 PSI. If supply pressure varies greatly from this, remove push

button (Item 3 - Figure 14) and adjust the screw on the regulator

(Item 18 - Figure 14). To remove push button, remove setscrew

from bottom of sleeve (Item 15). Insert a small punch in screw

hole and push up while grasping the push button and pull forward

removing the push button. Clockwise adjustment will raise stream

height and counterclockwise movement will lower stream height.

For best adjustment stream should hit basin approximately 6-1/2”

from the bubbler. Reassemble the push button by pushing in on

button until the push button catches in the sleeve. Reinstall the

setscrew (Item 6) in the sleeve (Item 15).

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 7

EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C

97921C (Rev. F - 02/18)

Figure 13 - Fountain Body

Figure 14 - Push Button

318

See Fig. 10 23

See Fig. 10

Figure 12 - Bubbler Details

NOTE:

When installing replacement bubbler and pedestal, tighten

locknut only to hold parts snug in position. Do Not overtighten.

Basin

Locknut

VANDAL RESISTANT

BUBBLER DETAIL

Basin

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 897921C (Rev. F - 02/18)

EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C

PARTS LIST

ITEM NO. PART NO. DESCRIPTION

56073C

28843C

98871C

55996C

1000001772

75632C

75560C

97446C

38417001

70432C

28708C

28473C

45767C

28343C

45781C

28397C

56092C

98530C

111008343890

AP99

56163C

0000000930

45768C

27089C

Bubbler Assy

Back Panel Assy EDFPBW(V)114C

Kit- Push Button/Spring/Pin/Washer

Strainer

Kit - Elbow 1/4 Stem x 1/4 (3 Pcs) 70817C

Setscrew - #10-32 x .31

Screw - 5/16-18 x 1.00 HHMS

VR Bubbler Assy

Screw - #8-18 x .37 HHSM

Screw - #8-32 x .38 THSM

Basin - Swirlow

Lower Shell

Fountain Body

Cover Plate

Sleeve

Back Panel

Poly Tubing (Cut To Length)

Kit - Regulator/Holder/Nut

Screw - #10-24 x .62 HHMS

AP-99 Panel (Optional)

Gasket - Drain

Assy - Drain/Tailpipe

Plug - Drain 1-1/2”

Hanger Bracket

Figure 17 – Water Supply Connections

TROUBLESHOOTING & MAINTENANCE

Orice Assembly: Mineral deposits on orice

can cause water ow to

spurt or not regulate. Mineral

deposits may be removed from

the orice by poking with a

small round le not over 1/8”

diameter, or using a small

diameter wire.

DO NOT le or cut

orice material.

Stream Regulator: If orice is clean, regulate ow

as in Step 8 of the installation instructions. If replace-

ment is necessary, see parts list for correct regulator

part number.

Actuation of Quick Connect Water Fittings: Cooler

is provided with lead-free

connectors which utilize an

o-ring water seal. To remove

tubing from the tting, relieve

water pressure, push in on

the gray collar while pulling

on the tubing. (See Figure

15) To insert tubing, push

tube straight into tting until

it reaches a positive stop

(approximately 3/4”).

Figure 15 – Quick Connect Fittings

Installing Back Panel: When installing back panel

assy. (Item 2) with MPW (Mounting Plate), attach

channel braces as shown above. Remove the pro-

tective backing from the tape installed on the braces.

Line up the corresponding holes in the braces and

back panel and press rmly in place.

Figure 16 – Back Panel Assembly

ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816

REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640

NS = NOT SHOWN

WWW.RESTROOMDIRECT.COM 704

•

937

•

2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay 4400BFEVGWR Installationshandbuch

Elkay

Elkay EFRC8C-A Installationshandbuch

Elkay

Elkay LK4420SFRK Bedienungsanleitung

Elkay

Elkay EDF214WC Installationshandbuch

Elkay

Elkay ERPA8C*A Installationshandbuch

Elkay

Elkay Soft Sides ECDFPW314FP Gebrauchsanweisung

Elkay

Elkay FLEXI-GUARD ESRC8 3GJO Series Installationshandbuch

Elkay

Elkay HTHBHAC8SSWF25WN Installationshandbuch

Elkay

Elkay Soft Sides ERO28C B Series Installationshandbuch

Elkay

Elkay 4405BFFR Bedienungsanleitung

Elkay

Elkay EHWM214C*A Installationshandbuch

Elkay

Elkay SOFT SIDES EDFPBM117WS Installationshandbuch

Elkay

Elkay 4410BF Bedienungsanleitung

Elkay

Elkay 4420BF1UFR Bedienungsanleitung

Elkay

Elkay SOFT SIDES EZLMSN-EDFPVM217DK Gebrauchsanweisung

Elkay

Elkay FLEXI-GUARD SOFT SIDES ezH2O EDFP217WS F... Gebrauchsanweisung

Elkay

Elkay 4595FR Bedienungsanleitung

Elkay

Elkay 4420BF1UDB Series Bedienungsanleitung

Elkay

Elkay Swirlflo EDFPB114FPC Installationshandbuch

Elkay

Elkay EHFRA7FC*A Installationshandbuch

Elkay

Elkay 4400FR Series Bedienungsanleitung

Elkay

Elkay Hydroboost HTHBHAC8BLSSWF25N Installationshandbuch

Elkay

Elkay Soft Sides ERO8C-C Installationshandbuch

Elkay

Elkay 4592 FTN Series Bedienungsanleitung

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung