Emax TINYHAWK III Bedienungsanleitung
Thanks for purchasing the Tinyhawk III.
Please follow the instruction manual to assemble and configure your Tinyhawk III.
Design in California, Made in China
Disclaimer
1. Please read the disclaimer carefully before using this product.
2. By using this product, you hereby agree to this disclaimer and signify that you have read
them carefully and completely.
3. This product is not suitable for people under the age of 18. Adult supervision is highly
recommended for kids under the age of 18.
4.Our Tinyhawk features open-source flight controller and Electronic Speed Controllers to
meet the FPV enthusiasts' need to upgrade their quad. Please read the instruction manual
and warnings carefully.
5.Before every flight, make sure the battery is fully charged and power connections are
secure.
6. DO NOT fly around crowds, children, animals or objects.
7. EMAX ACCEPTS NO LIABILITY FOR DAMAGE(S) OR INJURIES INCURRED DIRECTLY OR
INDIRECTLY FROM THE USE OF THIS PRODUCT.
Precautions
1.Please follow the instructions to assemble and to operate this product correctly.
2. Do not use this product if you have physical or mental illness, dizziness, fatigued, or use
while under the influence of alcohol or drugs.
3. Please fly in a safe area away from people
4. Do not modify or use other parts and accessories not approved for the use of EMAX.
5. Do not use this product in harsh environments (such as winds, rain, lightning, snow, etc.).
6. Do not use this product in a strong electromagnetic environment.
Contents
Product specifications.................................................................................................................... 4
Product list .........................................................................................................................................4
Tinyhawk III propeller ......................................................................................................................5
Tinyhawk III structure diagram.................................................................................................... 5
Propeller installation & removal.................................................................................................. 5
Tinyhawk III Video Transmission......... ....................................................................................... 7
Tinyhawk III image transmission diagram ................................................................................7
Betaflight OSD change VTX settings.......................................................................................... 7
Press key to set VTX channel ........................................................................................................7
Tinyhawk III receiver .......................................................................................................................10
Tinyhawk III receiver....................................................................................................................... 10
Binding step ......................................................................................................................................10
Other binding methods .................................................................................................................10
Tinyhawk III Flight Control............................................................................................................ 11
Tinyhawk III Flight Control Diagram ..........................................................................................11
Flight control settings ....................................................................................................................11
Introduction to PID Settings........................................................................................................ 11
Adjust software settings (Betaflight Configurator) ...............................................................12
Tinyhawk III flight control reprogramming .............................................................................12
Restore Tinyhawk III default settings ........................................................................................13
Tinyhawk III flight .............................................................................................................................14
Unlock................................................................................................................................................. 14
Airplane mode ..................................................................................................................................16
Advanced Flight-First Person View (FPV) Flight ....................................................................16
.
Product specification
Size and weight
Diagonal Wheelbase
(Without propeller)
76mm
Maximum size of Drone
(Without propeller)
L*W*H=105x105x45mm
Drone weight
(Without battery)
32g
Motor
TH0802 II 15000KV
Propeller
Avan TH Turnlemode-3
Main board
F4（ STM32F411 firmware）
4in1 5A ESC
EMAX Tiny receiver (SPI receive mode, Frsky D8 )
Camera
RunCam Nano 4 Camera
VTX
200-100-25MW adjustable frequency 37CH,
support SmartAudio
Battery
1S HV 450mAh
Product list
Tinyhawk III .................................................× 1
Emax 1s HV 450 mAh.............................. ×1
Charger.........................................................×1
Propeller..................................................... (2XCW, 2XCCW)
Spareparts.................................................... x 1
Tinyhawk III propeller
Tinyhawk III structure diagram
Propeller installation & removal
The Tinyhawk III propeller has two directions of rotation: clockwise (CW) and
counterclockwise (CCW). When purchasing a set of propellers, please purchase 2 clockwise
blades and 2 counterclockwise blades. The blade rotates along the blunt edge of the blade.
When installing the propeller blade, please install it in the correct direction of the propeller
blade as shown in the figure below.
Propeller installation
Align the 3 shafts of the propeller with the 3 shafts of the motor, supporting the back of the
motor, then press the blade in by hand until it is flush with the motor shaft.
Note: If the propeller is installed incorrectly, the Tinyhawk III cannot fly normally and cannot
be controlled. Please carefully check whether the propeller is in the correct direction; if there
is no support on the back of the motor, it may cause the frame to break; pay attention to
safety when installing the propeller.
Propeller disassembly
Use a small tool (such as a 1.5mm hex wrench or a small screwdriver) to press on the metal
at the bottom of the motor and Tinyhawk III. Grasp the blade of the propeller with your
fingers until the propeller pops out of the motor.
Note: It is only necessary to disassemble the propeller when replacing a new propeller; pay
attention to safety when dismantling the propeller and when using tools.
Tinyhawk VTX Settings
Vtx Schematic and Button Diagram
Changing VTX setting via Betaflight OSD
Tinyhawk III is equipped with SmartAudio and is already configured with stock settings. The
SmartAudio line is operated on UART 2 TX.
Follow the prompts on the screen to enter the main setting menu. The throttle is in the
middle, the direction is to the left, and the pitch is up (THROTTLE MID+ YAW LEFT+ PITCH
UP) to enter the OSD parameter adjustment menu, as shown in Figure 1.
In the menu interface, switch the pitch up/down (PITCH) and select the menu option. Move
the cursor to "FEATURES" and stir the ROLL lever to the right to enter the next menu. as
shown in Figure 2. Use the PITCH joystick to move the cursor to "VTX SA", as shown in
Figure 3. Then pull the roll (ROLL) lever to the right to enter the VTX configuration menu.as
shown in figure4.
In the menu of VTX SA, we can configure BAND, CHAN and POWER. Pull the PITCH lever to
move the cursor up and down to select the VTX option that needs to be set. Once the
parameters are set, move the cursor to "SET", then turn the joystick to the right, enter "SET"
and select "YES", turn the joystick to the right to save the set parameters, as shown in Figure
5.
In the VTX SA menu, move the cursor to "CONFIG" to enter the menu; move the cursor to
"PIT FMODE" and pull the ROLL lever to the right to turn off the VTX power supply.as
shown in figure6.
Press the key to set the VTX channel
Note: You must "disable" the VTX Smart Audio on UART 2 in order for the push-button
VTX adjustment to work as described below.
1.
Normal display
All LEDs on the VTX are normally off until the button is pressed. To check band and channel
status click the button once quickly, and LED starts to indicate frequency band and
frequency channel. First indicate the frequency band and then indicate the frequency
channel. After both 2 rounds of LED display cycles, all LEDs will turn off.
Press and hold the button for 5 seconds to enter the menu. After entering the menu, the
band LED lights up.
Press the button again for 5 seconds to save the parameters and exit the menu.
After saving and exiting the menu, all LED indicators are off.
Menu Entry / Exit
(1)Press the button and hold for 5s to enter the menu. After entering the menu, BAND LED
lights up.
(2)Press the button and hold for 5s again to save parameters and exit the menu. After
saving and exiting the menu, all LED goes out.
Band and Channel parameter change
After entering menu, short click button to switch frequency group band(b)/frequency
channel (C),and the LED of the corresponding menu is lit.
Enter/Exit Parameters
After choosing menu, press the button and hold for 2s to enter parameter option.
Notice: If you use SmartAudio to switch to an illegal channel, Tinyhawk III will not have
video transmission. To switch back to a legal channel, press the button on vtx and follow the
vtx menu guide shown below.
Default ≤ 25mW Output)
FCC: Ham radio license is required for use in North America.
EU/CE: The frequency is restricted to prevent transmission outside the specified CE
frequency.
Unlock configuration
FCC: Ham radio license is required for use in the USA.
EU/Europe: Do not use unlock configuration.
E-band channels 4, 7, and 8 are restricted to prevent transmission outside the
designated amateur radio frequencies. Adjustable video output power is only
applicable to specific models.
* When the user purchases this product, it means that he/she understands these
responsibilities and will operate the equipment legally. EMAX does not assume any
responsibility for the user's purchase and/or use of this product in violation of
government regulations.
Binding Procedure
Binding is the process of uniquely associating a particular receiver to a transmitter module.
A transmitter
module can be bound to multiple receivers (not to be used simultaneously). A receiver can
only be bound to one transmitter module.
1.Hold the bind button while powering on the receiver. When the BLUE LED is on, it means
the receiver is in BIND MODE
2.Turn on the transmitter, make sure it is set to D8 mode, and then set it into bind status.
When the BLUE LED of the receiver starts flashing, it means bind successful.
3.Turn on the transmitter again, the BLUE LED receiver will be on, it means the receiver is
receiving data from transmitter. Transmitter bind with receiver no need repetitive operation,
unless you change either receiver or transmitter.
The receiver can be instructed to enter the binding mode through the Betaflight
configurator. Type the following command in the CLI tab: bind_rx
Click the Enter key, your receiver will enter the binding mode, and then follow the binding
steps 2 and 3 to complete the binding process.
Andere Handbücher für TINYHAWK III
1
Inhaltsverzeichnis
Andere Emax Drohne Handbücher
Emax
Emax Tinyhawk II Bedienungsanleitung
Emax
Emax Babyhawk Bedienungsanleitung
Emax
Emax Babyhawk II HD Bedienungsanleitung
Emax
Emax Nanohawk 1S BNF FrSky Bedienungsanleitung
Emax
Emax Babyhawk Bedienungsanleitung
Emax
Emax Babyhawk O3 Bedienungsanleitung
Emax
Emax Hawk 5 PRO Bedienungsanleitung
Emax
Emax Hawk 5 Sport Bedienungsanleitung
Emax
Emax TinyHawk Freestyle Bedienungsanleitung
Emax
Emax Buzz Bedienungsanleitung
