Emerson Bettis RGS F Series Bedienungsanleitung

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

April 2016

Bettis RGS F-Series Double-Acting Actuators

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

Table of Contents

April 2016

Table of Contents

Section 1: Overviewn ��1

Section 2: Installation ��2

2.1 Valve Attachment ....................................................................................... 3

2.2 Accessory Mounting ................................................................................... 4

2.3 Piping and Operation.................................................................................. 4

2.4 Travel Adjustment....................................................................................... 7

Section 3: Troubleshooting ��9

Section 4: Maintenance ��10

4.1 Periodic Maintenance Schedule ................................................................ 10

4.2 Lubrication................................................................................................ 10

4.3 Piston Seal Replacement........................................................................... 10

4.4 Rod Seal Replacement .............................................................................. 13

4.5 Yoke Seal and Bushing Replacement......................................................... 15

4.6 Pins and Rollers Replacement ................................................................... 19

Appendix A: ��21

A.1 Force Module ............................................................................................ 21

A.2 Torque Module .......................................................................................... 23

April 2016

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

Section 1: Overview

Overview

Section 1: Overview

NOTE:

All activities must be carried out in order to ensure proper actuator operation. Always

read all instructions before beginning maintenance.

Bettis RGS F-Series actuators are composed of three basic sub-assemblies, two force

modules and a torque module. The force modules contain the pistons which provide

linear motion. The torque module contains the yoke which converts the force modules’

linear motion into torque and operates the valve.

Every actuator assembled by Bettis is tested prior to shipment to our customers.

Order specific documentation may be available upon request.

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

April 2016

Section 2: Installation

Installation

Section 2: Installation

Bettis actuators may be mounted in any position/orientation. If necessary, lift the actuator

with straps placed inside the framework of the body. Never lift the actuator by the cylinders,

tie rods, or travel stops. Lifting the actuator with the valve attached is not generally

recommended.

Figure 1

April 2016

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

Section 2: Installation

Installation

Larger sizes have lifting eyes incorporated into their body section which may be used to

lift the actuator.

Figure 2

2�1 Valve Attachment

NOTE:

Prior to mounting the actuator, verify alignment of coupler and shaft to ensure that the

valve will move to correct position.

Ensure the actuator is in the same position as the valve. It may be necessary to stroke

the actuator to determine the correct mounting orientation. Attach the actuator to the

valve using the proper bracket and coupler, or with a Bettis Universal Mounting Plate

(UMP) if provided. Using all mounting holes indicated on Bettis dimensional drawings,

tighten all fasteners hand tight then torque the fasteners to the corresponding value on

the table below.

Table 1�

Thread Pattern Ft-Lbs Nm

Accessories M5 3.4 4.6

F2200 M12 49 66

F2250/2300 M16 120 162

F2375 M20 235 318

F2488 M24 400 543

F2575 M30 800 1084

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

April 2016

Section 2: Installation

Installation

2�2 Accessory Mounting

As a standard, Bettis RGS F-Series actuators are provided with female 4mm slotted accessory

mounting geometry. When installing accessories, such as switch boxes or positioners,

tighten accessory mounting bolts hand tight, stroke the actuator three times to ensure

proper alignment then tighten the accessory mounting bolts to the proper torque. Check

the dimensional drawing or associated product bulletin for exact dimensions.

2�3 Piping and Operation

The operation of a Bettis RGS F-Series Double-Acting (DA) actuator is comparable to any

double-acting scotch yoke actuator.

Instrument air, water, and other power gases and fluids may be used to cycle the actuator so

long as construction materials were chosen accordingly and maximum allowable pressure is

not exceeded. Air driven stainless-steel actuators with stainless-steel or composite cylinders

are not harmed by wet air (so long as freezing does not occur). Aluminum and chrome-

plated steel cylinders may be harmed over time by the presence of water.

WARNING: DO NOT EXCEED PRESSURE RATING

Exceeding the stated maximum pressure may result in damage to equipment and danger

to personnel including severe injury or death. Consult the actuator label for operating

limits. If an actuator label is missing, contact Bettis to request a replacement.

WARNING: DO NOT EXCEED TEMPERATURE RATING

Operating outside of the minimum and maximum temperature range may result in damage

to equipment and danger to personnel including severe injury or death. Consult the

actuator label for operating limits. If an actuator label is missing, contact Bettis to request a

replacement. An example of an actuator label is provided below for your reference.

NOTE:

CE marking indicates product conforms to the requirements of applicable directives as

listed on the actuator label.

April 2016

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

Section 2: Installation

Installation

All Bettis actuators are shipped in the Left-Hand orientation unless ordered as Right-

Hand. The orientation may be reversed in the field by moving all accessories to the

opposite side of the shaft and turning the actuator top–side down.

Double-Acting (Left-Hand): pressure on the end cap ports pushes the pistons inward

and causes counterclockwise rotation. Pressure to the base plate ports pushes the

pistons outward resulting in a clockwise rotation.

Double-Acting (Right-Hand): pressure on the end cap ports pushes the pistons inward

and causes clockwise rotation. Pressure to the base plate ports pushes the pistons

outward resulting in a counterclockwise rotation.

Figure 3

Left-Hand

Right-Hand

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

April 2016

Section 2: Installation

Installation

Piping Guidelines:

• Both end cap pressure ports (P1 and P2) and both base plate pressure ports

(P3 and P4) must be utilized for proper operation.

• P1 and P2 are typically connected and powered by a single air pathway.

• P3 and P4 are typically connected and powered by a single air pathway.

• P5 is a breather port that should be fitted with a filter or strainer.

• On double-acting models, P5 may also be plugged without affecting

actuator operation.

Figure 4

P5 (2)

April 2016

Installation, Operation and Maintenance Manual

RGS011110-2 Rev. 0

Section 2: Installation

Installation

2�4 Travel Adjustment

The following instructions are for Left-Hand orientated actuators. For non-standard

models, clockwise and counterclockwise motion will be the inverse of what is

described below. Check the actuator model and orientation before adjusting the

Travel Stops.

Figure 5

Travel Stop

A-1

Travel Stops

B-1(x2)

Travel Stops

B-2 (x2)

Travel Stop

A-2

Set Clockwise Rotation (Travel Stops A)

1. Relieve all pressure from the actuator.

2. Loosen the Travel Stop nuts on Travel Stops A-1 and A-2. Be careful not to

misplace the travel stop O-rings.

3. Ensure actuator lockout (if provided) is disengaged.

4. Apply pressure to P3 and P4 to force the pistons fully outward, then relieve

all pressure.

5. Unthread Travel Stop A-2 four to five full turns.*

6. Adjust Travel Stop A-1 until travel is set to the desired position. It may be

necessary to apply pressure to P3 and P4 between adjustments to determine

final position

of travel.

7. Apply pressure to P3 and P4 and thread Travel Stop A-2 in until it is in firm

contact with the piston.

8. With pressure still applied to P3 and P4, tighten both travel stop nuts on Travel

Stops A until they are in contact with the end cap, then tighten an additional

1/4 turn.

*Clockwise rotation of the travel stops will shorten actuator stroke,

counterclockwise rotation will lengthen actuator stroke�

Inhaltsverzeichnis

Andere Emerson Controller Handbücher

Emerson

Emerson Hytork XL Series Installations- und Betriebsanleitung

Emerson

Emerson Fisher FIELDVUE DVC6005 Series Konfigurationshandbuch

Emerson

Emerson EL-O-Matic F-Series Installations- und Betriebsanleitung

Emerson

Emerson CASH VALVE A-360 Handbuch

Emerson

Emerson Tescom ER5000 Series Bedienungsanleitung

Emerson

Emerson E2 RX Series Bedienungsanleitung

Emerson

Emerson Bettis XTE3000 Bedienungsanleitung

Emerson

Emerson Fisher 67D Series Bedienungsanleitung

Emerson

Emerson EZH Series Bedienungsanleitung

Emerson

Emerson Dixell iChill IC200D EVO Series Verdrahtungsschema

Emerson

Emerson FISHER 627F Bedienungsanleitung

Emerson

Emerson EC2-712 Bedienungsanleitung

Emerson

Emerson Fisher 2503 Bedienungsanleitung

Emerson

Emerson AW Series Bedienungsanleitung

Emerson

Emerson FloBoss S600+ Bedienungsanleitung

Emerson

Emerson XM678D Technisches Datenblatt

Emerson

Emerson Dixell XR44CX Verdrahtungsschema

Emerson

Emerson Fisher 1066 Bedienungsanleitung

Emerson

Emerson IC200CX EVO Bedienungsanleitung

Emerson

Emerson Fisher 299H Bedienungsanleitung

Emerson

Emerson Bettis 500 Bedienungsanleitung

Emerson

Emerson FXMP25 Bedienungsanleitung

Emerson

Emerson BETTIS TEC2 CCM Installationshandbuch

Emerson

Emerson Fisher 656 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung