Emerson Unidrive M400 Bedienungsanleitung

Document Part # 026-4176 Rev 1 Page 1 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

The keypad and display gives information about the

operating status of the drive and trip codes. It provides

the ability to change parameters, stopping and starting

the drive, and the ability to perform a drive reset.

Keypad Number Keypad Description

1 (Enter)

The Enter button is used to enter

parameter view or edit mode, or to

accept a parameter edit.

2 (Navigation)

The Navigation keys can be used to

select individual parameters or to edit

parameter values. In keypad mode, the

“Up” and “Down” keys are alsoused to

increase or decrease the motor speed.

3 (Start) The Start key is used to start the drive in

keypad mode.

4 (Stop/Reset)

The Stop / Reset key is used to stop and

reset the drive in keypad mode. It can

also be used to reset the drive in

terminal mode.

5 (Escape)

The Escape key is used to exit from the

parameter edit / view mode or

disregard a parameter edit.

Figure 1 - Unidrive M400

Figure 2 - Unidrive M400 Keypad Details

Supervisory Controller Setup with

M400 VFD Drive

Quick Start Guide

This document will guide you through setting up and

commissioning the M400 VFD Drive in Supervisory

Controllers (E3 and Site Supervisor).

Complete All Programming Before you set up the M400

Drive.

Note that the M400 Drive requires Supervisory Controller

firmware version 2.14F01 and above.

Document Part # 026-4176 Rev 1 Page 2 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 1: Configuring M400 VFD Drive

Note: Do not connect the device communications to E2 controller.

1. Press right/ left arrow key and go to Pr MM.000 then press . Select Reset 60Hz defs then press

Note: Pressing allows you to enter and exit parameter edit mode.

2. Press to return the drive into the No Action display.

3. Go to Pr 00.005 (Drive Config), then press . Select Preset, then press .

4. Set Pr 00.010 (User Security Status), then press . Select All Menus, then press .

5. Set Pr 06.004 (Start/Stop Logic), then press . Select 6, then press .

6. Set Pr 11.023 (Serial Address), then press . Select 2, then press .

7. Set Pr 11.024 (Serial Mode), then press . Select 8 1 NP, then press .

8. Set Pr 11.020 (Serial Reset), then press . Select On to reset communications.

Note: The device will flash to On and returns to Off, press .

9. Set Pr 12.000 (Parameter mm.000), then press . Select Save Parameters, then press .

10.Press to return the drive into the No Action display.

Note: The drive is now ready to communicate with the Supervisory controller and is ready for a test/run.

Model Max # of Instances

1 SR 20

2CXe 16

3CX 16

4BXe 16

5BX 16

6RXe 16

7RX 16

8SMF No

Document Part # 026-4176 Rev 1 Page 3 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 2: Setting the Baud Rate in the Supervisory Controller

Gear icon > Configure System Properties > General System Properties

• Set the Com Port baud to 19.2

Figure 3 - General System Properties Tree Hierarchy

Figure 4 - Set the Baud Rate, Data Size, Parity, and Stop Bits

Document Part # 026-4176 Rev 1 Page 4 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 3: Wiring the M400 VFD Device to Emerson Controllers

Wire the device as shown below:

COM wiring is the REVERSE polarity of Site Supervisor.

•+ On the Com port goes to - on the VFD.

•- On the Com port goes to the + on the VFD.

• Do NOT connect shield to any terminal on the controller or VFD. Connect shield directly to Earth Chassis at the

controller; clip and insulate shield at VFD end of cable.

• If VFD is the last device at the end of Com segment, terminate with 150 ohms between terminals 2 and 3.

Figure 5 - Wire the M400 VFD Device to Site Supervisor

Document Part # 026-4176 Rev 1 Page 5 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

COM wiring is the same polarity as E2 and E3.

•+ On the Com port goes to + on the VFD.

•- On the Com port goes to - on the VFD.

• Do NOT connect shield to any terminal on the controller or VFD. Connect shield directly to Earth Chassis at the

controller; clip and insulate shield at VFD end of cable.

• If VFD is the last device at end of Com segment, terminate with 150 ohms between terminals 2 and 3.

Figure 6 - Wire the M400 VFD Device to E2/E3

Document Part # 026-4176 Rev 1 Page 6 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 7 - Site Supervisor to M400 (MODBUS)

Document Part # 026-4176 Rev 1 Page 7 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 8 - Site Supervisor to M400 (ANALOG 0-10V)

Document Part # 026-4176 Rev 1 Page 8 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 9 - Lumity E3 to M400 (MODBUS)

Document Part # 026-4176 Rev 1 Page 9 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 10 - Lumity E3 to M400 (ANALOG 0-10V)

Document Part # 026-4176 Rev 1 Page 10 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 4: Adding the Device to the Supervisory Controller

1. From the home page click the control inventory icon to go to the Control Inventory page.

2. From the HVAC drop-down list, select M400 from the list.

STEP 5: Commissioning the Device to the Supervisory Controller

From the Control Inventory screen select the Modbus address for the M400 and click the checkmark

to save and start commissioning. (Best practices tip: set the Modbus number to match the connected

Com Port and the Address to match the M400 addressing in STEP 1).

Drive Setup:

1. Click the M400 to go to the M400 setup page.

2. Go to the General tab.

3. Set CfgSyncAction on the to Write to Device.

4. On the Inputs tab, set DIRECTION to Forward or Reverse. This verifies that the drive should run

correctly.

5. Set RUN to OFF. This verifies that the drive should inhibit.

Figure 11 - Adding M400 and Addressing

Andere Handbücher für Unidrive M400

Inhaltsverzeichnis

Andere Emerson Controller Handbücher

Emerson

Emerson FieldQ Series Betriebshandbuch

Emerson

Emerson DXP-FF Gebrauchsanweisung

Emerson

Emerson FISHER 912N Series Bedienungsanleitung

Emerson

Emerson Fisher 67D Series Bedienungsanleitung

Emerson

Emerson Dixell XR03CH Verdrahtungsschema

Emerson

Emerson FISHER T208 Series Bedienungsanleitung

Emerson

Emerson Dixell XR70CX Verdrahtungsschema

Emerson

Emerson TARTARINI PS/80-1 Bedienungsanleitung

Emerson

Emerson EC3-D72 Bedienungsanleitung

Emerson

Emerson FISHER LR128 Series Bedienungsanleitung

Emerson

Emerson FISHER P650 Bedienungsanleitung

Emerson

Emerson Leroy Somer R250 Bedienungsanleitung

Emerson

Emerson EC3-932 Bedienungsanleitung

Emerson

Emerson Fisher 92S Bedienungsanleitung

Emerson

Emerson Fisher 630 Series Bedienungsanleitung

Emerson

Emerson EC20 Series Bedienungsanleitung

Emerson

Emerson Aventics 617 Series Bedienungsanleitung

Emerson

Emerson Fisher FIELDVUE DVC6005 Series Bedienungsanleitung

Emerson

Emerson Bettis 2000 Series Handbuch

Emerson

Emerson Dixell XRi30T Verdrahtungsschema

Emerson

Emerson Dixell XC645CX Bedienungsanleitung

Emerson

Emerson CSB600 Series Bedienungsanleitung

Emerson

Emerson Dixell XR44CH Verdrahtungsschema

Emerson

Emerson FISHER 66 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung