Emerson DIXELL XWEB1000D PRO Verdrahtungsschema

XWEB1000D PRO

TABLE OF CONTENTS

1. PRODUCT DISPOSAL (WEEE)................................................................................................5

2. THE RECIPIENTS OF THIS MANUAL .......................................................................................5

3. PACKAGE.............................................................................................................................5

4. TECHNICAL DATA.................................................................................................................6

5. INSTALLATION......................................................................................................................7

5.1 XWEB WIRING DIAGRAMs ...................................................................................................7

5.2 CONTROLLERS................................................................................................................... 9

5.3 CONFIGURATION FOR XC400/600/800/900 and XH200/300/400 SERIES .................................. 11

5.4 CONFIGURATION FOR XJA/XJP/XJM MODELS ....................................................................... 11

5.5 USING A DC VOLT METER TOCHECK XWEB TERMINATION AND BIAS....................................... 11

6. REMOTE CONNECTIVITY ..................................................................................................... 12

6.1 DESKTOP SOFTWARE REQUIREMENTS (PC).......................................................................... 12

6.2 SOFTWARE MOBILE REQUIREMENTS (SMARTPHONE/TABLET)................................................ 12

6.3 CROSSOVER CABLE INSTRUCTIONS ..................................................................................... 13

6.4 INTRANET CONNECTIVITY (“OR LAN CONNECTION”) AND VPN................................................ 14

6.5 INTERNET CONNECTIVITY ON PUBLIC IP .............................................................................. 15

6.6 WIFI CONNECTIVITY ......................................................................................................... 16

7. CLEANOUT.......................................................................................................................... 17

8. OPERATIVE PROCEDURES.................................................................................................. 17

9. SYSTEM IDENTIFICATION.................................................................................................... 18

10. TRADEMARKS..................................................................................................................... 18

11. NOTES................................................................................................................................ 19

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 3/19

CAUTION: TO PREVENT FLAMES FROM DEVELOPING OR ELECTRIC SHOCK,

AVOID ANY CONTACT BETWEEN THISDEVICEAND RAIN OR WATER

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER IT DOES NOT

CONTAIN ANY PARTS THAT REQUIRE SERVICING BY

THE USER ALWAYS HAVE QUALIFIED STAFF

PERFORM THE PROCEDURES.

THE SYMBOL OF THE LIGHTNING BOLT INSIDE AN

EQUILATERAL TRIANGLE IS USED TO ALERT THE

USER OF THE POTENTIALLY DANGEROUS NON-

INSULATED ELECTRICAL VOLTAGES

THE SYMBOL OF THE EXCLAMATION MARK INSIDE

AN EQUILATERAL TRIANGLE IS USED TO WARN THE

USER THAT HE/SHE MUST PAY CLOSE ATTENTION

TO THE TOPIC COVERED IN THIS MANUAL

CAUTION

This device must be installed exclusively by service staff with suitable technical

training and experience,who are aware of the dangersthat they are exposed to.

The operations described herein are set forth exclusivelyfor the service staff. The

user is not enabled to open the device.

CAUTION

Use only modems and usb-donglesofficially supported by this monitoring unit. Dixell

srl. cannot be held responsible for any type of damage resulting from the use of

unsupported devices.

CAUTION

Dixell srl reserves therightto amend thismanual withoutprior notice. The latest

available version can be downloaded fromthe internetsite.

CAUTION

Immediately after the power failure,no new data is recorded; all recorded data is

kept in non-volatile memory. The memory is electronic and no data is kept or

conveyed to other media such aspaper.When the memory isexhausted,the oldest

data is lost to store the most recent data. The product provides memory

consumption indicationson the user interface.The device does not have its own

power supply. The recording interval can be configured from a minimum of 30

seconds to a maximum of1 day. The duration ofthe recordings depends on the

interval and the number of points configured for each device in configuration. One

yearof data logging is guaranteed for 2 analog resources with an interval of 15

minutes, per configured device. Selecting other resources can affect storage

performance.

CAUTION

This is a Class A product. In adomestic environment,thisproductmaycauseradio

interference in which case the user maybe required to take adequate measures

CAUTION

Dixell srl reserves therightto vary the composition of its products without prior

notice to the customer, ensuring the identical and unchanged features of the same

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 4/19

CAUTION

The product is not suitable for environments subjectto mechanical vibrations and

does not withstand shocks. It must be installed in a dryand clean environment.

CAUTION

The customer shall bear full responsibility and risk for product configuration in order

to achieve the results pertaining to installation and/or final equipment/system. Upon

the customer's request and following a specific agreement, Dixell s.r.l. maybe

present during the start-up of the final machine/application,as a consultant,

however, under no circumstancescan the company be held responsible for the

correct operation of the final equipment/system.

CAUTION

Since Dixellproducts form partof a very high level of technology, a

qualification/configuration/programming/commissioning stage is required to use

them as best as possible.Otherwise,these products may malfunction and Dixell

cannot be held responsible. The product must notbe used in any way thatdiffers

from thatstipulated in the documentation

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 5/19

1. PRODUCT DISPOSAL (WEEE)

With reference to the DIRECTIVE 2012/19 / UE OFTHE EUROPEAN PARLIAMENTAND OF THE

COUNCIL of 4 July 2012 on Waste Electrical and Electronic Equipment (WEEE), and to the relevant national

implementation regulations, we inform you thatusers of EEEin households:

➢There is an obligation not to dispose of WEEE as mixed urban waste and to separate waste collection of

WEEE;

➢Public orprivate collection systems required by local laws must be used for disposal. It is also possible,

at the end of its life,to return the equipment to the distributor in case of purchase of a new one.

➢This equipment may contain hazardoussubstances; improper use or incorrect disposal could have

negative effects on human health and the environment.

➢The symbol shown on the product or on the packaging indicatesthatthe productmustbe treated

with separate waste.

➢In case of incorrect disposal, sanctions can be applied as established by the local laws on waste

disposal.

2. THE RECIPIENTS OF THIS MANUAL

The contentsof thismanual are intended for professionalusers, such as XWEB installers.It may also be of

use to the administrator of the network that it is connected to.

The mechanical product drawings required for any form of intervention and the possible network

configurationsare all an integral part of this manual.

3. PACKAGE

Before opening the package make sure that the packaging is intact and thatthere is no sign of impact or

tampering. Before starting any operation, itis necessaryto checkthat the XWEB box contains:

•1 XWEB Unit

•1 Installation Manual

•1 Cross Cable 1mt

•Removable female connector

1x2 ways,

5x3 ways

1x4 ways

1x6 ways

•jumpers

If one of the following parts is damaged, promptly contact yourdealer.

You may also receive a modem or a wifi dongle- which will not be included in the same package - as a

package option.When working with a modemconnection, alwayscheck that the type of modem you are

about to install is a Dixell approved model;as it cannot be held responsible for the malfunctioning of devices

not expressly approved by it.

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 6/19

4. TECHNICAL DATA

XWEB is DIN Rail mounting compatible. Snap the orange tabs on the back of theunit to the down position to

fasten. If not using the DIN Rail mounting option, fasten to the mounting surface using the openings in the

mounting tabs.

Dimensions

183 x 110 x 59.1 mm

Weight (without

accessories)

436g

Mounting

DINrail mounting device

Degree of Protection

Indoor use, Open Type (NEMA - UL 50e)

Enclosure Rating

UL 94 V-0

Power

24Vac, 20VA

Overvoltage Category

Rated Impulse Voltage

2500V

Type of Action

1.B of N.O.;1.Cof N.C. (Relay1-4)

PollutionDegree

Ambient Operating

Temperature

-40 to 140 °F (-40°Cto 65°C)

Shippingand storage

temperature

-40÷85 °C

Relative Humidity

20-85% RHnoncondensing

Digital Inputs

2, Dry contacts

Relay Outputs

Digital Output Ratings

Relay 1 (N.O. & N.C.) 5A, 125/240 VAC, General Purpose, 100K

cycles; 4FLA/4LRA, 250VAC,MotorLoad,100K cycles;

Relay 2 (N.O. & N.C.) 5A, 125/240 VAC, General Purpose, 100K

cycles; 4FLA/4LRA,250VAC, Motor Load, 100K cycles;

Relay 3 (N.O. & N.C.) 5A, 125/240VAC, General Purpose, 100K

cycles; 4FLA/4LRA,250VAC, MotorLoad, 100K cycles;

RS485 ports

MODBUS Com Ports1, 2, 3, 4

Ethernet ports

Ports ETH1, ETH1, ETH0 (ETH1 has no IP)

USB Ports

MicroSD

Purpose of control

Operating control

Construction of control

Incorporated control, intended to be used in Class Ior Class II

equipment

Approvals

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 7/19

5. INSTALLATION

5.1 XWEB WIRING DIAGRAMS

For installation, the XWEB systemmust notbe opened in any way. If the boxis opened, the warranty will

lapse. XWEB-EVO can be installed in various ways based on the model and type of user interface access

that you wish to provide for the final user. The features ofthesetypes of connectivity are described herein.

CAUTION: in order to protect yourself and the XWEB, turn on the unit only after connecting all the electrical

devices. In order to avoid accidentaloperation,connect the power cord only after connecting all the other

external units.

1-2

Powersupply24Vac

USB ext. peripherals

ETH0, ETH1

RJ45 LAN connector

Cmn

RS485

COM1, COM2, COM3,

COM4

Relay 1

(System alarm relay)

Relay 2

(AUX1)

Relay 3

(AUX2)

Digital Input1

Digital Input2

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 8/19

LEDS

•“Rectangle LED”: Poweron / Cleanout

•“Triangle LED”: Alarm / Cleanout

Micro SD

Removable storage media currently used for Backup / Restore functions.

Note: The media must alreadybe inserted at the XWEBEVO poweron. It is notmounted "on the fly"

Reset Button

As long asit is pressed, the deviceis off. Verysimilar to the reset button on PC

On release, the system restarts asper power on.

•Avoid direct passage between operators as much as possible (to avoid electrostatic

induction and subsequent discharges);

•If the electrical voltage supply differs from the required rating, this could seriously damage

the system;

•Connection errors (and connections that differ from the prescribed ones) can pose a danger

to operator safety and cause faults in the system and to the instruments that are connected

to it;

•Insert one or more easily accessible disconnecting devices to the exterior of the device to

separate the device from the power mains;

•Do not use the device in environments with flammable gases.

•Do not modify the device in any way.

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 9/19

5.2 CONTROLLERS

XWEB has at least one RS485 serial port, on which the line of the controllerdevicescan be connected. If

there are more serials,more device lines can be served.

Most Dixell controller devices are equipped with an RS485 serialoutput and can be connected without the

need for any additional module or connection cable. To make sure of this possibility, check the

characteristics of the controller in its manual.

Some Dixell devices however, may not be direct, but it can be obtained via the small external Dixell

XJRS485 or DixellXJ485 converter. It converts the controller outputfrom"TTL" (five wires) to "485" (two

wires). If you need to use the TTL / 485 converter, please pay attention in:

•Keep the TTL cable away from any source of electromagnetic disturbance

•Connect each XJ485 module to the instrumentwith the TTL cable supplied with the module itself

•Mark the polarity of output 485 which must be respected when connecting the instruments to the

network

Below is a list of operating tips to obtain the best result in termsof instrument network reliability, RS485

serial connection:

•The serial line cable can be of the two-wire type plusthe shield, with a minimumsection of 0.5mm2

(eg BELDEN 8772).This cable is recommended for its technical characteristics and for maintaining

the quality of the electrical signal;

•The serial line cable must reachall the instrument stations: check the plant layout and the various

distances thatthe cable will have to travel;

•The serial line cable can reach a maximum length of 1 km

•Respect the polaritiesindicated on the instrument withthose of the cablesleading to the serial

•Keep the serial cable away from power cables and any possible source of electromagnetic

disturbance

•Do not connect the shield of the serial cable to the earth of the electrical system

•Do not connect the “Gnd” terminal.

•Drawa map of the installation you are performing: it will beusefulboth in case of problems and in

case of future changes; the serial line must reach all the stations where the instruments must be

controlled.

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 10/19

•Do not branch into the line:

Correctconnection

Incorrectconnection

On the same line, each controller is normally programmed with its own unique serialaddress, through the

Adr parameter. Refer to the installation manual of the instrument itself for the access and modification

procedure. To obtain a simple description of the categoriesto which they belong,divide the programming of

the addresses progressively.Some special cases are listed on the following pages.

To keep the RS485 line balanced,the ends must be terminated with a 1500Ω resistor. If the XWEBis at one

end of the RS485 line, it is advisable to insert the 120Ω termination resistor on the last instrument and on the

XWEB. To activate the EOL resistor,insert enable TERM. DO NOTenable it if the XWEBis in the middle of

the RS485 line.

On/Off

Pos1

Term

Pos2

Bias

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson CSI 2140 Bedienungsanleitung

Emerson

Emerson Machinery Health Expert CSI 2600 Bedienungsanleitung

Emerson

Emerson Rosemount 8750WB Bedienungsanleitung

Emerson

Emerson Rosemount Apex Bedienungsanleitung

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson MICRO MOTION HFVM Series Kurzanleitung

Emerson

Emerson FB3000 Bedienungsanleitung

Emerson

Emerson Rosemount 8750WA Bedienungsanleitung

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Emerson

Emerson Rosemount 54eA Bedienungsanleitung

Emerson

Emerson Rosemount CT4215 Bedienungsanleitung

Emerson

Emerson FB1200 Kurzanleitung

Emerson

Emerson Fisher 4320 Bedienungsanleitung

Emerson

Emerson AMS Bedienungsanleitung

Emerson

Emerson Rosemount 3410 Series Programmierhandbuch

Emerson

Emerson Rosemount Xi Bedienungsanleitung

Emerson

Emerson Rosemount 3051SAL Bedienungsanleitung

Emerson

Emerson Rosemount 3410 Series Programmierhandbuch

Emerson

Emerson 755A Bedienungsanleitung

Emerson

Emerson RLDS Betriebsanleitung

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson Rosemount 2090P Bedienungsanleitung

Emerson

Emerson World Class 3000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung