Emerson EE542-1Z Bedienungsanleitung

EE542-1Z

Installation Manual

Smart EnergyProgrammable Thermostat + Energy Monitor

20 - 22

Back Cover

Contents

Introduction

Getting Started

Installing the Thermostat

Quick Guide

Step 1: Remove the Old Thermostat

Step 2: Mount the New Thermostat

Step 3: Configure the Thermostat

Step 4: Check Thermostat Operation

Step 5: Pair Device to Home Area Network

Step 6:Verify Wireless Connectivity

Wiring Chart

Wiring Table

Introduction

• About this Guide

• System Compatibility

This guide describes how to install and configure your new

Smart Energy thermostat.

This product replaces most thermostats, including those

that work with:

• Standard Heat and Cool Systems

• Two-Stage Heat and Two-Stage Cool Systems

• Air Source Heat Pump (with Aux. or Emergency Heat)

• Ground Source Heat Pump (with Aux. or Emergency Heat)

• Air or Ground Source Heat Pump (No Aux. or Emergency Heat)

• Standard Heat Only Systems

• Standard Central Air Conditioning

• Gas or Oil Heat

• Electric Furnace

• Hydronic (Hot Water) Zone Heat – 2 Wire zone valves

Failure to read and follow all instructions carefully before installing or

operating this control could cause personal injury and/or property

damage.

To prevent electrical shock and/or equipment damage, disconnect

electric power to system at main fuse or circuit breaker box until

installation is complete.

Do not use on circuits exceeding specified voltage. Higher voltage will

damage control and could cause shock or fire hazard.

CAUTION

Getting Started

Note: This product requires a

24v AC power supply via the

C terminal for operation.

• Thermostat (1)

• Wall anchors (2)

• Mounting screws (2)

Required Items

• Flat blade screwdrivers – 1 large and 1 micro tip

• Hand or power drill with 3/16 inch drill bit

• Wire strippers

• Level (optional)

Required Tools

Before you begin to install your Smart Energy thermostat:

Read these instructions thoroughly.

Check the package from your thermostat to make sure you have

all of the required items (see below).

Check to ensure you have the required tools (see below).

Pre-Installation Checklist

O/B

W/E

To prevent electrical shock and/or equipment damage, disconnect

electric power to system at main fuse or circuit breaker box until

installation is complete.

CAUTION

Quick Guide

• Turn off power at the breaker.

• Remove cover from old thermostat to expose wires.

• Document which wires go to which terminals using the table

on the back of this manual.

• Disconnect wires and remove old thermostat, making sure that

thermostat wires do not fall back into wall opening.

STEP 1. Remove the old thermostat

• Feed thermostat wires through thermostat hole.

• Wire new thermostat.

• Turn on power at breaker.

STEP 2. Mount the new thermostat

STEP 3. Configure the thermostat

STEP 4. Check thermostat operation

STEP 5.Verify wireless connectivity

The sections that follow provide detailed instructions

for completing these steps.

To prevent electrical shock and/or equipment damage, disconnect electric

power to system at main fuse or circuit breaker box until installation is

complete.

CAUTION

This product does not contain mercury. However this product may replace a

product that contains mercury.

Mercury and products containing mercury must not be discarded in household

trash. Do not touch any spilled mercury. Wearing non-absorbent gloves, clean up

any spilled mercury and place in a sealed container. For proper disposal of a

product containing mercury or a sealed container of spilled mercury, place it in a

suitable shipping container. Refer to www.thermostat-recycle.org for location to

send the product containing mercury.

ATTENTION: MERCURY NOTICE

STEP 1. Remove the Old Thermostat.

1. Cover

2. Base, which you can remove by loosening all screws

3. Wall plate, which you can remove by unscrewing the

mounting screws that hold it on the wall or adaptor plate

Thermostat Components

Most thermostats consist of three basic parts.

Wall plateBase

Cover

3-Part Thermostat

Remove the Old Thermostat

Important: Do not let wires fall back into the wall.

1. Remove the front cover of the old thermostat.

2. With wires still attached, remove wall plate from the

wall by loosening the screws. If the old thermostat has a wall

mounting plate, remove both the thermostat and the wall

mounting plate.

3. Identify each wire attached to the old thermostat as shown in the

diagram below. Before removing wires from old thermostat,

label each wire with the letter on the old thermostat or document

the color of wire going into each terminal in the table located on

the back cover of this manual.

4. Disconnect the wires from the old thermostat one at a time.

Wall opening

Wall plate hanging on the wires

You may want to wrap the wires

around a pencil to keep them from

falling back into the wall.

TIP

Wall opening

O/B

W/E

Take care when securing and routing wires so they do not short to

adjacent terminals or rear of thermostat. Personal injury and/or

property damage may occur.

CAUTION

STEP 2. Mount the New Thermostat

1. Unpack the thermostat and separate the mounting plate from the

thermostat. Remove the packing material from the thermostat.

Gently pull the thermostat straight off of the base. Hold the back

of the thermostat by the lower corners with one hand, and pull

the wall plate off with the other hand.

Feed thermostat wires through rectangular hole between the

terminal blocks in the thermostat wall plate.

Mount the new thermostat

NOTE: Forcing or prying on the thermostat will cause damage to the unit.

Wall plate

Feed wires through

this hole from back

Mounting

holes

O/B

W/E

Once you have established the desired location of the thermostat,

use a pencil, and the wall plate as a template, to mark the

location of the mounting holes on your wall.

Move wall plate out of the way and drill two holes using a

3/16" drill bit.

Feed the thermostat wires through the rectangular hole and

fasten wall plate loosely to wall using two mounting screws in

mounting holes.

If desired, place a level against bottom of the wall plate and

adjust until level before tightening screws (leveling is for

appearance only and does not affect thermostat operation).

If you are using existing mounting holes, or if holes drilled are

too large and do not allow you to tighten base snugly, use

plastic wall anchors included with the product.

Connect wires to the thermostat wall plate. The image below

shows the location of the wire terminals. Each terminal is

labeled with a letter or letter number combination.

Wall plate

Wire

Terminals

Feed wires through

this hole from back Connect

wires here

Connect wires as follows:

• If necessary, strip insulation about 3/8 inch from the end

of the wire.

• Use the table you previously filled out on the back of the

installation manual (or the wiring chart on page 20) to locate

the correct terminal for each wire connection.

• Bend the wire slightly, insert the wire under the contact plate,

and use a small flat head screwdriver to secure the wire

into place.

Push excess wire into wall and plug hole with a fire resistant

material (such as fiberglass insulation) to prevent drafts from

affecting thermostat operation.

8 Fasten thermostat to wall plate using the quick connect feature.

Make sure the retention tabs on the wall plate are in line with

the retention slots on the thermostat. Gently press the

thermostat onto the wall plate until you hear a clicking sound.

If the thermostat does not easily click do not press with

excessive force or damage could occur to the product.

9. Turn power back on at the breaker.

Andere Handbücher für EE542-1Z

Inhaltsverzeichnis

Andere Emerson Thermostat Handbücher

Emerson

Emerson Dixell XR35CX - 110VAC Bedienungsanleitung

Emerson

Emerson 1A16 series Bedienungsanleitung

Emerson

Emerson 80 Series Bedienungsanleitung

Emerson

Emerson 7903 Betriebsanleitung

Emerson

Emerson White-Rodgers 1F75H-21PR Bedienungsanleitung

Emerson

Emerson White Rodgers 1F80-0224 Bedienungsanleitung

Emerson

Emerson 1F94-80 Bedienungsanleitung

Emerson

Emerson 1F85U-42PR Bedienungsanleitung

Emerson

Emerson 1F80-361 Bedienungsanleitung

Emerson

Emerson 1F75C-11PR Bedienungsanleitung

Emerson

Emerson 1F80-0471 Bedienungsanleitung

Emerson

Emerson White-Rodgers P210 Bedienungsanleitung

Emerson

Emerson 1F95EZ-0671 Montageanleitung

Emerson

Emerson White Rodgers 755-50 Bedienungsanleitung

Emerson

Emerson Inspire 1HDEZ-1521 Bedienungsanleitung

Emerson

Emerson 1F83H-21PR Bedienungsanleitung

Emerson

Emerson 1F83C-11NP Bedienungsanleitung

Emerson

Emerson 1F78-151 Bedienungsanleitung

Emerson

Emerson XW10L Bedienungsanleitung

Emerson

Emerson 1F86ST-0471 Bedienungsanleitung

Emerson

Emerson 1F83-0471 Bedienungsanleitung

Emerson

Emerson VERDANT VX Series Bedienungsanleitung

Emerson

Emerson OH-1202 Bedienungsanleitung

Emerson

Emerson SENSI TOUCH 2 1F96U-42WF Series Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung