Emerson Rosemount 2088 Bedienungsanleitung

Quick Start Guide

00825-0100-4108, Rev EA

February 2019

Rosemount™ 2088, 2090F, and 2090P

Pressure Transmitter

with 4–20 mA HART® and 1–5 Vdc Low

Power HART Protocol (Revision 5 and 7)

Safety messages for Rosemount 2088,2090F, and 2090P Transmitters.

NOTICE

This guide provides basic guidelines for Rosemount 2088,2090F, and 2090P Transmitters. It does

not provide instructions for configuration, diagnostics, maintenance, service, troubleshooting,

Explosion-proof, Flameproof, or intrinsically safe(I.S.)installations.

See the Rosemount 2088 Reference Manual for more information. This manual is also available

electronically on Emerson.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Review the approvals section of this

manual for any restrictions associated with a safe installation.

Before connecting a handheld communicator in an explosive atmosphere, make sure the

instruments in the loop are installed in accordance with intrinsically safe or non-incendive field

wiring practices.

In an explosion-proof/flameproof installation, do not remove the transmitter covers when power

is applied to the unit.

Process leaks could result in death or serious injury.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adapter.

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.

Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all entries

will have the same thread form. Only use plugs, adapters, glands, or conduit with a compatible thread

form when closing these entries.

Contents

System readiness........................................... 3

Mount the transmitter................................... 6

Set the switches...........................................10

Connect the wiring and power up................ 12

Verify transmitter configuration using a Field

Communicator............................................ 15

Trim the transmitter.................................... 21

Safety Instrumented Systems (SIS) installation

.................................................................... 24

Product certifications...................................25

Rosemount™ 2088 and 2090 Declaration of

Conformity.................................................. 44

China RoHS.................................................. 47

Quick Start Guide February 2019

2 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide

1 System readiness

Confirm HART® revision capability

•If using HART-based control or asset management systems, confirm the

HART capability of those systems prior to transmitter installation. Not all

systems are capable of communicating with HART Revision 7 Protocol.

This transmitter can be configured for either HART Revision 5 or 7.

•For instructions on how to change the HART revision of the transmitter,

see Switch HART Revision mode.

1.1 Confirm correct device driver

•Verify the latest device driver (DD/DTM™) is loaded on your systems to

ensure proper communication.

Note

The Rosemount™ 2088, 2090F, and 2090P Transmitters all use Rosemount

2088 Device Revisions and Drivers.

Procedure

1. Download the latest DD at Emerson.com or FieldCommGroup.org.

2. In the Browse by Member dropdown menu, select Emerson.

3. Select desired product.

a) Reference Table 1-1 and Table 1-2, Find Device Driver Files

column to find the correct device driver.

Table 1-1: Rosemount 2088 and 2090 with 4–20 mA HART Device Revisions and

Files

Release

date

Device identification Device driver

identification

Review

instructions

Review

functionality

NAMUR

revision(1)

HART revision(2) Device

revision(3)

Reference

manual

Change

description(4)

(5)

Hardware Software Universal

Aug-16 1.1.xx 1.0.xx 3 7 10 Rosemount

2088

Reference

Manual

Rosemount

2090

Reference

Manual

(5)

5 9

Jan-13 N/A 1.0.xx 1 7 10 (4)

5 9

February 2019 Quick Start Guide

Quick Start Guide 3

Table 1-1: Rosemount 2088 and 2090 with 4–20 mA HART Device Revisions and

Files (continued)

Release

date

Device identification Device driver

identification

Review

instructions

Review

functionality

NAMUR

revision(1)

HART revision(2) Device

revision(3)

Reference

manual

Change

description(4)

(5)

Hardware Software Universal

Jan-98 N/A N/A 178 5 3 N/A

(1) NAMUR revision is located on the hardware tag of the device. Differences in level 3 changes,

signified above by xx, represent minor product changes as defined per NE53. Compatibility

and functionality are preserved and product can be used interchangeably.

(2) HART® software revision can be read using a HART capable configuration tool. Value shown

is minimum revision that could correspond to NAMUR revisions.

(3) Device driver file names use device and DD revision, e.g. 10_01. HART Protocol is designed

to enable legacy device driver revisions to continue to communicate with new HART devices.

To access new functionality, the new device driver must be downloaded. It is recommended

to download new device driver files to ensure full functionality.

(4) HART Revision 5 and 7 selectable, Local Operator Interface(LOI), scaled variable,

configurable alarms, expanded engineering units.

(5) Updated electronics hardware design. Intrinsic Safety temperature classification change.

Table 1-2: Rosemount 2088 with 1–5 Vdc Low Power HART Device Revisions and

Files

Release

date

Device identification Device driver

identification

Review

instructions

Review

functionality

NAMUR

revision(1)

HART revision(2) Device

revision(3)

Reference

manual

Change

description(4)

Hardware Software Universal

Jan-13 N/A 1.0.2 3 7 10 Rosemount

2088

Reference

Manual

Rosemount

2090

Reference

Manual

(4)

5 9

Jan-98 N/A N/A 178 5 3 N/A

(1) NAMUR revision is located on the hardware tag of the device. Differences in level 3 changes,

signified above by xx, represent minor product changes as defined per NE53. Compatibility

and functionality are preserved and product can be used interchangeably.

(2) HART software revision can be read using a HART capable configuration tool. Value shown

is minimum revision that could correspond to NAMUR revisions.

(3) Device driver file names use device and DD revision, e.g. 10_01. HART Protocol is designed

to enable legacy device driver revisions to continue to communicate with new HART devices.

Quick Start Guide February 2019

4 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide

To access new functionality, the new device driver must be downloaded. It is recommended

to download new device driver files to ensure full functionality.

(4) HART Revision 5 and 7 selectable, Local Operator Interface(LOI), scaled variable,

configurable alarms, expanded engineering units.

February 2019 Quick Start Guide

Quick Start Guide 5

2 Mount the transmitter

2.1 Rosemount™ 2088

Mount directly to the impulse line without using an additional mounting

bracket or mount directly to a wall, panel, or two-inch pipe using an optional

mounting bracket.

2.2 Rosemount™ 2090P

Mount directly to the process pipe using an existing weld spud, or have a

skilled welder install a new weld spud using a TIG welder. Refer to Reference

Manual for complete welding instructions. Improper installation may result in

weld spud distortion. Recommended mounting in upright or horizontal

position to allow proper draining of vent.

2.3 Rosemount™ 2090F

Mount directly to the process pipe using a standard sanitary fitting (either a

1.5- or 2-in. Tri Clamp connection). Recommended mounting in upright or

horizontal position to allow proper draining of vent.

Figure 2-1: Transmitter Direct Mounting

Do not apply torque directly to the electronics housing. To avoid damage,

apply torque only to the hex-shaped process connection.

Rosemount

2088

Rosemount 2090P Rosemount

2090F

A. ½–14 NPT female process connection

B. Vessel wall

C. Weld spud

D. O-ring

E. 1½- or 2-in. Tri Clamp connection

Quick Start Guide February 2019

6 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide

Figure 2-2: Panel and Pipe Mounting

Panel mount Pipe mount

2.4 Liquid flow applications

Transmitter mounting procedure for liquid flow applications.

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

Example

2.5 Gas flow applications

Transmitter mounting procedure for gas flow applications.

Procedure

1. Place taps in the top or side of the line.

2. Mount level or above the taps.

February 2019 Quick Start Guide

Quick Start Guide 7

Example

2.6 Steam flow applications

Transmitter mounting procedure for steam flow applications.

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Example

2.7 Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to

provide a water/dust tight conduit seal and meets requirements of NEMA®

Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are

required. For M20 threads, install conduit plugs to full thread engagement or

until mechanical resistance is met.

Quick Start Guide February 2019

8 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide

2.8 Gage transmitter orientation

The low side pressure port (atmospheric reference) on the gage transmitters

with aluminum housings are located in the neck of the transmitter, behind the

housing. The vent path is 360° around the transmitter between the housing

and sensor. (See Figure 2-3.)

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so that the process can

drain away.

Figure 2-3: Gage Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

February 2019 Quick Start Guide

Quick Start Guide 9

3 Set the switches

Set alarm and security switch configuration before installation as shown in

Figure 3-1.

•The alarm switch sets the analog output alarm to high or low. Default

alarm is high.

•The security switch allows ( ) or prevents ( ) any configuration of the

transmitter. Default security is off ( ).

Use the following procedure to change the switch configuration:

Procedure

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side. Do not

remove the instrument cover in explosive atmospheres when the

circuit is live.

3. Slide the security and alarm switches into the preferred position using

a small screwdriver.

4. Reattach the transmitter cover. The cover must be fully engaged to

comply with explosion-proof requirements.

Figure 3-1: Transmitter Electronics Board

Without LCD display With LOI/LCD display

A. Alarm

B. Security

Quick Start Guide February 2019

10 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide

Andere Handbücher für Rosemount 2088

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson PT5N FLR Series Bedienungsanleitung

Emerson

Emerson PT5N Series Bedienungsanleitung

Emerson

Emerson Micro Motion 1700 Kurzanleitung

Emerson

Emerson Micro Motion 3500 Bedienungsanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson Micro Motion Transmitters and Discrete Controllers Series... Betriebshandbuch

Emerson

Emerson Rosemount 327T Bedienungsanleitung

Emerson

Emerson Rosemount 5402 Bedienungsanleitung

Emerson

Emerson Liebert SL-31080 Bedienungsanleitung

Emerson

Emerson Rosemount 5081 Bedienungsanleitung

Emerson

Emerson MicroMotion FOUNDATION 5700 Bedienungsanleitung

Emerson

Emerson ROSEMOUNT 5300 Konfigurationshandbuch

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount X-STREAM O2 Transmitter Bedienungsanleitung

Emerson

Emerson Rosemount 2088 Bedienungsanleitung

Emerson

Emerson Rosemount Oxymitter 4000 Bedienungsanleitung

Emerson

Emerson Micro Motion 1000 Series Kurzanleitung

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount CX1100 Bedienungsanleitung

Emerson

Emerson Rosemount 4088B MultiVariable Bedienungsanleitung

Emerson

Emerson Rosemount 8712EM Bedienungsanleitung

Emerson

Emerson Rosemount 2051CF series Bedienungsanleitung

Emerson

Emerson Rosemount 705 Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung