Emerson Rosemount 2090 Konfigurationshandbuch

Manual Supplement

00809-0200-4108, Rev AB

December 2018

Rosemount™2090 Pressure Transmitter

Safety Instrumented Systems (SIS) Requirements

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1

SIS operation and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4

1.0 Overview

The safety-critical output of the Rosemount 2090 Pressure Transmitter is provided through a two-wire,

4–20 mA signal representing pressure. The Rosemount 2090 safety certified pressure transmitter is

certified to: Low Demand; Type B.

SIL 2 for random integrity @ HFT=0

SIL 3 for random integrity @ HFT=1

SIL 3 for systematic integrity

1.1 Rosemount 2090 safety certified identification

All Rosemount 2090 transmitters must be identified as safety certified before installing into SIS systems.

To identify a safety certified Rosemount 2090:

1. Check Namur Software Revision located on the metal device tag. “SW _._._”.

Namur Software Revision Number

SW(1) 1.0.x –1.4.x

1. NAMUR Software Revision: Located on the metal device tag

2. Verify that option code QT is included in the transmitter model code.

1.2 Installation in SIS applications

Installations are to be performed by qualified personnel. No special installation is required in addition to

the standard installation practices outlined in this document. Always ensure a proper seal by installing

the electronics housing cover(s) so that metal contacts metal.

Environmental and operational limits are available in “Specifications and Reference Data,” in the

Reference Manual.

The loop should be designed so the terminal voltage does not drop below 10.5 Vdc when the transmitter

output is set to 23 mA.

Manual Supplement

00809-0200-4108, Rev AB

Rosemount 2090 Pressure Transmitter

December 2018

Rosemount 2090 Pressure Transmitter

Position the security switch to the ( ) position to prevent accidental or deliberate change of

configuration data during normal operation.

1.3 Configuring in SIS applications

Use any HART capable configuration tool to communicate with and verify configuration of the

Rosemount 2090.

Note

Transmitter output is not safety-rated during the following: configuration changes, multidrop, and loop

test. Alternative means should be used to ensure process safety during transmitter configuration and

maintenance activities.

1.4 Damping

User-selected damping will affect the transmitters ability to respond to changes in the applied process.

The damping value + response time must not exceed the loop requirements. See the Reference Manual.

1.5 Alarm and saturation levels

DCS or safety logic solver should be configured to match transmitter configuration. Figure 1-1 identifies

the three alarm levels available and their operation values.

Figure 1-1. Alarm levels

1. Transmitter Failure, hardware or software alarm in LO position.

2. Transmitter Failure, hardware of software alarm in HI position.

Rosemount alarm level

Normal Operation

3.75 mA(1) 4 mA 20 mA 21.75(2)

3.9 mA

low saturation

20.8 mA

high saturation

Namur alarm level

Normal Operation

3.6 mA(1) 4 mA 20 mA 22.5(2)

3.8 mA

low saturation

20.5

high saturation

Custom alarm level

Normal Operation

3.6 - 3.8 mA(1) 4 mA 20 mA 20.2 - 23.0(2)

3.7 - 3.9 mA

low saturation

20.1 - 22.9 mA

high saturation

Manual Supplement

00809-0200-4108, Rev AB

Rosemount 2090 Pressure Transmitter

December 2018

Rosemount 2090 Pressure Transmitter

2.0 SIS operation and maintenance

2.1 Proof test

The following proof tests are recommended. In the event that an error is found in the safety and

functionality, proof test results and corrective actions taken can be documented at Emerson.com/Rose-

mount/SafetyWeb-Apps/Report-A-Failure.

All proof test procedures must be carried out by qualified personnel.

Use Field Communicator Menu Trees and Fast Keys to perform a Loop Test, Analog Output Trim, or

Sensor Trim. Security switch should be in the ( ) position during proof test execution and repositioned

in the ( ) position after execution. See Appendix D of the Reference Manual.

2.2 Partial proof test

The simple suggested proof test consists of a power cycle plus reasonability checks of the transmitter

output. Reference the FMEDA Report for percent of possible DU failures in the device.

FMEDA report can be found at: Emerson.com/Rosemount/Safety-Products.

Required tools: Field Communicator and mA meter.

1. Bypass the safety function and take appropriate action to avoid a false trip.

2. Use HART®Communications to retrieve any diagnostics and take appropriate action.

3. Send a HART command to the transmitter to go to the high alarm current output and verify that the

analog current reaches that value(1). See Verifying alarm level in the Reference Manual.

4. Send a HART command to the transmitter to go to the low alarm current output and verify that the

analog current reaches that value(1).

5. Remove the bypass and otherwise restore the normal operation.

6. Place the Security switch in the ( ) position.

2.3 Comprehensive proof test

The comprehensive proof test consists of performing the same steps as the simple suggested proof test

but with a two point calibration of the pressure sensor in place of the reasonability check. Reference the

FMEDA Report for percent of possible DU failures in the device.

Required tools: Field Communicator and pressure calibration equipment.

Manual Supplement

00809-0200-4108, Rev AB

Rosemount 2090 Pressure Transmitter

December 2018

Rosemount 2090 Pressure Transmitter

1. Bypass the safety function and take appropriate action to avoid a false trip.

2. Use HART communications to retrieve any diagnostics and take appropriate action.

3. Send a HART command to the transmitter to go to the high alarm current output and verify that the

analog current reaches that value(1). See Verifying alarm level, in the Reference Manual.

4. Send a HART command to the transmitter to go to the low alarm current output and verify that the

analog current reaches that value (2).

5. Perform a two-point calibration check of the sensor (see Section 5: Trim the pressure signal in the

Reference Manual) over the full working range and verify the current output at each point.

6. Remove the bypass and otherwise restore the normal operation.

7. Place the Security switch in the ( ) position.

1. This test for possible quiescent current related failures.

2. This tests for compliance voltage problems such as a low loop power supply voltage or increased wiring distance. This also tests for other possible failures.

Note

The user determines the proof test requirements for impulse piping.

Automatic diagnostics are defined for the corrected percent DU: The tests performed internally by

the device during runtime without requiring enabling or programming by the user.

2.4 Calculation of average probability of failure on demand (PFDAVG)

PFDAVG calculation can be found in the FMEDA report located at: Emerson.com/Rose-

mount/Safety-Products.

3.0 Inspection

3.1 Product repair

The Rosemount 2090 is not repairable and must be replaced in case of failure.

All failures detected by the transmitter diagnostics or by the proof-test must be reported. Feedback can

be submitted electronically at Emerson.com/Rosemount/SafetyWeb-Apps/Report-A-Failure.

All product repair and part replacement should be performed by qualified personnel.

3.2 Rosemount 2090 SIS reference

The Rosemount 2090must be operated in accordance to the functional and performance specifications

provided in Specifications and Reference Data in the Reference Manual.

Manual Supplement

00809-0200-4108, Rev AB

Rosemount 2090 Pressure Transmitter

December 2018

Rosemount 2090 Pressure Transmitter

3.3 Failure rate data

The FMEDA report includes failure rates and common cause Beta factor estimates. The report is available

at Emerson.com/Rosemount/Safety-Products.

3.4 Failure values

Transmitter response time: Reference Appendix A: specifications and reference data in the Reference

Manual.

Self-diagnostics test interval: At least once every 60 minutes

3.5 Product life

50 years - based on worst case component wear-out mechanisms - not based on wear-out of process

wetted materials

Report any safety related product information at: Emerson.com/Rosemount/Safety-

Web-Apps/Report-A-Failure

Manual Supplement

00809-0200-4108, Rev AB

December 2018

Global Headquarters

Emerson Automation Solutions

6021 Innovation Blvd.

Shakopee, MN 55379, USA

+1 800 999 9307 or +1 952 906 8888

+1 952 949 7001

RFQ.RMD-RCC@Emerson.com

North America Regional Office

Emerson Automation Solutions

8200 Market Blvd.

Chanhassen, MN 55317, USA

+1 800 999 9307 or +1 952 906 8888

+1 952 949 7001

RMT-NA.RCCRFQ@Emerson.com

Latin America Regional Office

Emerson Automation Solutions

1300 Concord Terrace, Suite 400

Sunrise, FL 33323, USA

+1 954 846 5030

+1 954 846 5121

RFQ.RMD-RCC@Emerson.com

Europe Regional Office

Emerson Automation Solutions Europe GmbH

Neuhofstrasse 19a P.O. Box 1046

CH 6340 Baar

Switzerland

+41 (0) 41 768 6111

+41 (0) 41 768 6300

RFQ.RMD-RCC@Emerson.com

Asia Pacific Regional Office

Emerson Automation Solutions

1 Pandan Crescent

Singapore 128461

+65 6777 8211

+65 6777 0947

[email protected]

Middle East and Africa Regional Office

Emerson Automation Solutions

Emerson FZE P.O. Box 17033

Jebel Ali Free Zone - South 2

Dubai, United Arab Emirates

+971 4 8118100

+971 4 8865465

RFQ.RMTMEA@Emerson.com

Linkedin.com/company/Emerson-Automation-Solutions

Twitter.com/Rosemount_News

Facebook.com/Rosemount

Youtube.com/user/RosemountMeasurement

Google.com/+RosemountMeasurement

Emerson Terms and Conditions of Sale are available upon request.

The Emerson logo is a trademark and service mark of Emerson Electric Co.

Rosemount and Rosemount logotype are trademarks of Emerson.

All other marks are the property of their respective owners.

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson MICRO MOTION 2700 Bedienungsanleitung

Emerson

Emerson Rosemount 3408 Bedienungsanleitung

Emerson

Emerson Rosemount FCL-01 Bedienungsanleitung

Emerson

Emerson Micro Motion 9739 MVD Kurzanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson 5301HxxxxxxxxxxxxxxZZSeries Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Micro Motion IFT9701 Bedienungsanleitung

Emerson

Emerson Micro Motion 4200 Kurzanleitung

Emerson

Emerson Rosemount OCX 8800 Bedienungsanleitung

Emerson

Emerson Rosemount 2088 Bedienungsanleitung

Emerson

Emerson Micro Motion 2400S Bedienungsanleitung

Emerson

Emerson Rosemount 3300 Series Bedienungsanleitung

Emerson

Emerson Rosemount 1208A Bedienungsanleitung

Emerson

Emerson MICRO MOTION 1500 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Micro Motion 9739 MVD Kurzanleitung

Emerson

Emerson Rosemount MultiVariable 4088A Bedienungsanleitung

Emerson

Emerson PT5N FLR Series Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 1199 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Micro Motion 1700 Kurzanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung