Emerson Rosemount 5408 Bedienungsanleitung

Quick Start Guide

00825-0500-4408, Rev AA

October 2017

Rosemount™5408 and 5408:SIS Level

Transmitters

Process Seal Antenna

October 2017

Quick Start Guide

1.0 About this guide

This Quick Start Guide provides basic guidelines for the Rosemount 5408 and

5408:SIS Level Transmitters.

Refer to the Rosemount 5408 and 5408:SIS Reference Manual for more

instructions. The manual and this guide are also available electronically on

Emerson.com/Rosemount.

Failure to follow safe installation and service guidelines could result in death or serious injury.

Make sure the transmitter is installed by qualified personnel and in accordance with applicable code of

practice.

Use the equipment only as specified in this guide and the Rosemount 5408 and 5408:SIS Reference Manual.

For installations in hazardous locations, the transmitter must be installed according to the Rosemount 5408

and 5408:SIS Product Certifications document and System Control Drawing (D7000002-885).

Repair, e.g. substitution of components etc. may jeopardize safety and is under no circumstances allowed.

Explosions could result in death or serious injury.

Verify that the operating environment of the transmitter is consistent with the appropriate hazardous

locations certifications.

Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in the

loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.

Do not remove the transmitter covers in explosive atmospheres when the circuit is alive.

Both transmitter covers must be fully engaged to meet explosion-proof requirements.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause

electrical shock.

Make sure the main power to the transmitter is off and the lines to any other external power source are

disconnected or not powered while wiring the transmitter.

Process leaks could result in death or serious injury.

Make sure that the transmitter is handled carefully. If the process seal is damaged, gas might escape from

the tank.

Hot surfaces

The flange and process seal may be hot at high process temperatures.

Allow to cool before servicing.

Quick Start Guide

October 2017

2.0 Confirm approval type

For hazardous locations transmitters labeled with multiple approval types:

Permanently mark the checkbox of the selected approval type(s).

Contents

Confirm approval type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3

Mount the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4

Align transmitter head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8

Adjust display orientation (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10

Prepare the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11

Connect wiring and power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12

Configure transmitter using Guided Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17

October 2017

Quick Start Guide

3.0 Mount the transmitter

3.1 Installation procedure

Flanged version

Tri Clamp version

page 5

page 7

Quick Start Guide

October 2017

3.2 Flanged version

Step 1: Lower the transmitter into the nozzle

Note

Be careful not to scratch or otherwise damage the PTFE sealing.

PTFE sealing

October 2017

Quick Start Guide

Step 2: Tighten the bolts and nuts

Note

Re-tighten after 24 hours and again after the first temperature cycle.

Check at regular intervals and re-tighten if necessary.

Step 3: Align the transmitter head (see page 8)

Table 1. Torque Value, lb-ft (N-m)(1)(2)

1. The conditions used for the calculation are: Standard mating metal flange, A193 B8M Cl.2 / A4-70

bolt material, and a friction coefficient of μ=0.16.

2. Low strength bolt and non-metallic mating flange may require lower tightening torque.

Process

connection size

Process connection rating

ASME B16.5 EN1092-1 JIS B2220

Class 150 Class 300 PN6 PN10/PN16 PN25/PN40 10K

2-in./DN50/50A 29 (40) 52 (70) 15 (20) 26 (35) 29 (40) 18 (25)

3-in./DN80/80A 33 (45) 48 (65) 37 (50) 37 (50) 41 (55) 22 (30)

4-in./DN100/100A 59 (80) 52 (70) 37 (50) 37 (50) 74 (100) 26 (35)

Quick Start Guide

October 2017

3.3 Tri Clamp version

Step 1: Lower the transmitter into the nozzle

Note

Be careful not to scratch or otherwise damage the PTFE sealing.

Step 2: Tighten the clamp

Tighten the clamp to the recommended torque (see the manufacturer’s

instruction manual).

Step 3: Align the transmitter head (see page 8)

PTFE sealing

October 2017

Quick Start Guide

4.0 Align transmitter head

Open tank

Align the marking on sensor module toward the tank wall.

Still pipe

Align the external ground screw toward the holes of the still pipe.

Chamber

Align the external ground screw toward the process connections.

Quick Start Guide

October 2017

Step 1: Loosen the nut slightly and turn the transmitter

Step 2: Verify transmitter is properly aligned

See page 8 for direction.

Step 3: Tighten the nut

Torque 355 in-lb (40 N-m)

60 mm

October 2017

Quick Start Guide

5.0 Adjust display orientation (optional)

To improve field access to wiring or to better view the optional LCD display:

1. Loosen the set screw until the transmitter housing can rotate smoothly.

2. First, rotate the housing clockwise to the desired location. If the desired

location cannot be achieved due to thread limit, rotate the housing

counterclockwise to the desired location (up to 360° from thread limit).

3. Re-tighten the set screw.

Figure 1. Rotate the Transmitter Housing

H3/32 in.

Torque 30 in-lb (3 N-m)

Andere Handbücher für Rosemount 5408

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 3051D Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 5081 Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 4088A Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Series Bedienungsanleitung

Emerson

Emerson wirelessHART Rosemount Series Bedienungsanleitung

Emerson

Emerson Rosemount 2088 Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 3408 Bedienungsanleitung

Emerson

Emerson Rosemount 5600 Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 648 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S ERS Bedienungsanleitung

Emerson

Emerson Rosemount 4088B MultiVariable Bedienungsanleitung

Emerson

Emerson CSI 9420 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount FCL-01 Bedienungsanleitung

Emerson

Emerson Rosemount 3408 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung