Emerson Rosemount 3051 Bedienungsanleitung

Quick Start Guide

00825-0100-4797, Rev ED

October 2016

Rosemount™3051 Pressure Transmitter

and Rosemount 3051CF Series Flowmeter

with PROFIBUS®PA Protocol

00825-0100-4797_RevED.fm Page 1 Monday, October 17, 2016 4:31 AM

October 2016

Quick Start Guide

NOTICE

This installation guide provides basic guidelines for Rosemount 3051 Transmitters. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-Proof,

Flame-Proof, or intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 Reference Manual for

more instruction. This manual is also available electronically on EmersonProcess.com/Rosemount.

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate local,

national, and international standards, codes, and practices. Review the approvals section of the Rosemount

3051 Reference Manual for any restrictions associated with a safe installation.

In an Explosion-Proof/Flameproof installation, do not remove the transmitter covers when power is

applied to the unit.

Process leaks may cause harm or result in death.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adapter.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread form. Only

use plugs, adapters, glands or conduit with a compatible thread form when closing these entries.

Contents

Mount the transmitter. . . . . . . . . . . . . . . . . . . . . 3

Consider housing rotation . . . . . . . . . . . . . . . . . 7

Set jumpers and switches . . . . . . . . . . . . . . . . . . 7

Connect wiring and power up . . . . . . . . . . . . . . 8

Basic configuration . . . . . . . . . . . . . . . . . . . . . . 10

Trim the transmitter . . . . . . . . . . . . . . . . . . . . . 13

Product Certifications. . . . . . . . . . . . . . . . . . . . 14

00825-0100-4797_RevED.fm Page 2 Monday, October 17, 2016 4:31 AM

Quick Start Guide

October 2016

1.0 Mount the transmitter

1.1 Liquid applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the

drain/vent valves are oriented upward.

1.2 Gas applications

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

1.3 Steam applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Flow

00825-0100-4797_RevED.fm Page 3 Monday, October 17, 2016 4:31 AM

October 2016

Quick Start Guide

1.4 Mounting options

Panel mount(1)

1. Panel bolts are customer supplied.

Pipe mount

Coplanar flange

Traditional flange

Rosemount 3051T

00825-0100-4797_RevED.fm Page 4 Monday, October 17, 2016 4:31 AM

Quick Start Guide

October 2016

1.5 Bolting considerations

If the transmitter installation requires assembly of the process flanges, manifolds,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitters. Use only bolts supplied

with the transmitter or sold by Emerson™Process Management as spare parts.

Figure 1 illustrates common transmitter assemblies with the bolt length required

for proper transmitter assembly.

Figure 1. Common Transmitter Assemblies

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange adapters

Bolts are typically carbon steel or stainless steel. Confirm the material by viewing

the markings on the head of the bolt and referencing Table 1. If bolt material is

not shown in Table 1, contact the local Emerson Process Management

representative for more information.

Use the following bolt installation procedure:

1. Carbon steel bolts do not require lubrication and the stainless steel bolts are

coated with a lubricant to ease installation. However, no additional lubricant

should be applied when installing either type of bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing pattern.

See Table 1 for final torque value.

5. Verify the flange bolts are protruding through the isolator plate before

applying pressure.

4 × 1.75-in. (44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.88-in. (73 mm)

4 × 1.75-in. (44 mm)

4 × 1.50-in.

(38 mm)

4 × 2.25-in.

(57 mm)

00825-0100-4797_RevED.fm Page 5 Monday, October 17, 2016 4:31 AM

October 2016

Quick Start Guide

Table 1. Torque Values for the Flange and Flange Adapter Bolts

1.6 O-rings with flange adapters

Whenever the flanges or adapters are removed, visually inspect the O-rings.

Replace them if there are any signs of damage, such as nicks or cuts. If you replace

the O-rings, re-torque the flange bolts and alignment screws after installation to

compensate for seating of the PTFE O-ring.

1.7 Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to

provide a water/dust tight conduit seal and meets requirements of NEMA Type

4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are

required.

For M20 threads, install conduit plugs to full thread engagement or until

mechanical resistance is met.

1.8 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

Bolt material Head markings Initial torque Final torque

Carbon Steel (CS) 300 in-lb 650 in-lb

Stainless Steel (SST) 150 in-lb 300 in-lb

Failure to install proper flange adapter O-rings may cause process leaks, which can result in death or

serious injury. The two flange adapters are distinguished by unique O-ring grooves. Only use the

O-ring that is designed for its specific flange adapter, as shown below:

A. Flange adapter

B. O-ring

C. PTFE based (profile is square)

D. Elastomer (profile is round)

B7M

316

STM

316

B8M

Rosemount 3051S/3051/2051

00825-0100-4797_RevED.fm Page 6 Monday, October 17, 2016 4:31 AM

Quick Start Guide

October 2016

transmitter is located in the neck of the transmitter, behind the housing.

The vent path is 360° around the transmitter between the housing and sensor.

(See Figure 2.)

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so that the process can drain

away.

Figure 2. In-line Gage Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

2.0 Consider housing rotation

To improve field access to wiring or to better view the optional LCD display:

1. Loosen the housing rotation set screw.

2. First, rotate the housing clockwise to the desired location. If the desired

location cannot be achieved due to thread limit, rotate the housing counter

clockwise to the desired location (up to 360° from thread limit).

3. Retighten the housing rotation set screw.

Figure 3. Housing Rotation Set Screw

A. Housing rotation set screw (5/64-in.)

3.0 Set jumpers and switches

3.1 Security

After the transmitter is configured, you may want to protect the configuration

data from unwarranted changes. Each transmitter is equipped with a security

jumper than can be positioned “ON” to prevent the accidental or deliberate

change of configuration data. The jumper is labeled “Security”. The security

jumper also prevents changes made using the Local Operator Interface.

00825-0100-4797_RevED.fm Page 7 Monday, October 17, 2016 4:31 AM

October 2016

Quick Start Guide

3.2 Simulate

The simulate jumper is used in conjunction with the analog input (AI) block. This

jumper is used to simulate the pressure measurement and is used as a lock-out

feature for the AI block. to enable the simulate feature, the jumper must be

moved to the “ON” position after power is applied. This feature prevents the

transmitter from being accidentally left in simulate mode.

Figure 4. Transmitter Jumper Locations

4.0 Connect wiring and power up

Use the following steps to wire the transmitter:

1. Remove the housing cover on the field terminals side.

2. Connect the power leads to the terminals indicated on the terminal block

label.

Power terminals are polarity insensitive - connect positive or negative to

either terminal

3. Ensure full contact with Terminal Block screw and washer. When using a direct

wiring method, wrap wire clockwise to ensure it is in place when tightening

the terminal block screw.

Note

The use of a pin or a ferrule wire terminal is not recommended as the connection may be

more susceptible to loosening over time or under vibration.

4. Ensure proper grounding. It is important that the instrument cable shield:

Be trimmed close and insulated from touching the transmitter housing

Be connected to the next shield if cable is routed through a junction box

Be connected to a good earth ground at the power supply end

5. Plug and seal unused conduit connections.

6. If applicable, install wiring with a drip loop. Arrange the drip loop

so the bottom is lower than the conduit connections and the

transmitter housing.

7. Replace the housing cover.

ROSEMOUNT 3051

PROFIBUS PA OUTPUT

00825-0100-4797_RevED.fm Page 8 Monday, October 17, 2016 4:31 AM

Quick Start Guide

October 2016

Figure 5. Terminals

A. Power terminals

B. Ground terminal

Note: “NC” is a No Connect terminal (do not use)

Figure 6. Wiring

4.1 Signal wiring grounding

Do not run signal wiring in conduit or open trays with power wiring, or near heavy

electrical equipment. Grounding terminations are provided on the outside of the

electronics housing and inside the terminal compartment. These grounds are

used when transient protect terminal blocks are installed or to fulfill local

regulations. See Step 2 below for more information on how the cable shield

should be grounded.

1. Remove the Field Terminals housing cover.

A. 6234 ft (1900 m) max

(depending upon cable characteristics)

B. Integrated power conditioner and filter

C. Terminators

D. Power supply

E. DP/PA coupler/link

F. Trunk

G. DP network

H. Signal wiring

I. Spur

J. PROFIBUS PA device

00825-0100-4797_RevED.fm Page 9 Monday, October 17, 2016 4:31 AM

October 2016

Quick Start Guide

2. Connect the wiring pair and ground as indicated in Figure 7. The cable shield

should:

Be trimmed close and insulated from touching the transmitter housing.

Continuously connect to the termination point.

Be connected to a good earth ground at the power supply end.

Figure 7. Wiring

3. Replace the housing cover. It is recommended the cover be tightened until

there is no gap between the cover and the housing.

4. Plug and seal unused conduit connections.

Power supply

The dc power supply should provide power with less than two percent ripple. The

transmitter requires between 9 and 32 Vdc at the terminals to operate and

provide complete functionality

Power conditioner

The DP/PA coupler/link often includes an integrated power conditioner.

Grounding

Transmitters are electrically isolated to 500 Vac rms. Signal wiring can not be

grounded.

Shield wire ground

Grounding techniques for shield wire usually require a single grounding point for

shield wire to avoid creating a ground loop. The ground point is typically at the

power supply.

5.0 Basic configuration

5.1 Configuration tasks

The transmitter can be configured via either the local operator interface (LOI) –

option code M4, or via a Class 2 Master (DD or DTM™based). The two basic

A. Minimize distance

B. Trim shield and insulate

C. Ground for transient protection

D. Connect shield back to the power supply ground

E. Insulate shield

00825-0100-4797_RevED.fm Page 10 Monday, October 17, 2016 4:31 AM

Andere Handbücher für Rosemount 3051

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 550PT Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 1152 Alphaline Bedienungsanleitung

Emerson

Emerson Rosemount 2090 Konfigurationshandbuch

Emerson

Emerson Rosemount 5300 Series Betriebshandbuch

Emerson

Emerson Micro Motion 5700 Kurzanleitung

Emerson

Emerson Rosemount MultiVariable 4088A Bedienungsanleitung

Emerson

Emerson Rosemount 6888A Bedienungsanleitung

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 3308 Bedienungsanleitung

Emerson

Emerson Rosemount 3051G Bedienungsanleitung

Emerson

Emerson PT5N FLR Series Bedienungsanleitung

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount OCX 8800 Bedienungsanleitung

Emerson

Emerson Rosemount Wireless Permasense WT210 Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051 CF Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung