Emerson Rosemount 8782 Bedienungsanleitung

Quick Start Guide

00825-0100-8782, Rev AA

November 2019

Rosemount™ 8782 Slurry Magnetic Flow

Meter Transmitter

1 Safety

WARNING

•Failure to follow these installation guidelines could result in serious injury

or death.

•Installation and servicing instructions are for use by qualified personnel

only. Do not perform any servicing other than that contained in the

operating instructions, unless qualified.

•Potential electrostatic charging hazard: Rosemount Magnetic flow

meters ordered with non-standard paint options or non-metallic labels

may be subject to electrostatic discharge. To avoid electrostatic charge

build-up, do not rub the flow meter with a dry cloth or clean with

solvents.

•Verify that the operating environment of the sensor and transmitter is

consistent with the appropriate Agency Approval.

•If installed in an explosive atmosphere, verify that the device certification

and installation techniques are suitable for that particular environment.

•To prevent ignition of flammable or combustible atmosphere,

disconnect power before servicing circuits.

•Explosion hazard: Do not disconnect equipment when a flammable or

combustible atmosphere is present.

•Follow national, local, and plant standards to properly earth ground the

transmitter and sensor. The earth ground must be separate from the

process reference ground.

•Shock hazard: Shut off power before servicing. Do not operate without

power compartment cover.

CAUTION

•In cases where high voltage/high current are present near the meter

installation, ensure proper protection methods are followed to prevent

stray voltage/current from passing through the meter. Failure to

adequately protect the meter could result in damage to the transmitter

and lead to meter failure.

•Completely remove all electrical connections from both sensor and

transmitter prior to welding on the pipe. For maximum protection of the

sensor, consider removing it from the pipeline.

Quick Start Guide November 2019

2 Rosemount™ 8782 Slurry Magnetic Flow Meter Transmitter

2 Introduction

This document provides basic installation guidelines for the Rosemount

8782 Magnetic Slurry wall-mount transmitter.

•For sensor installation refer to the Rosemount™ MS Magnetic Slurry Flow

Meter Sensor Quick Installation Guide

•For additional installation information, configuration, maintenance, and

troubleshooting, refer to the Rosemount™ 8782 Magnetic Slurry Flow

Meter with HART Protocol Reference Manual

All user documentation can be found at www.emerson.com. For more

contact information see Emerson Flow customer service.

2.1 Return policy

Emerson procedures must be followed when returning equipment. These

procedures ensure legal compliance with government transportation

agencies and help provide a safe working environment for Emerson

employees. Failure to follow Emerson procedures will result in your

equipment being refused delivery.

November 2019 Quick Start Guide

Quick Start Guide 3

2.2 Emerson Flow customer service

Email:

•Worldwide: [email protected]

•Asia-Pacific: [email protected]

Telephone:

North and South America Europe and Middle East Asia Pacific

United States 800 522 6277 U.K. 0870 240

1978

Australia 800 158 727

Canada +1 303 527

5200

The

Netherlands

+31 (0) 704

136 666

New Zealand 099 128 804

Mexico +41 (0) 41

7686 111

France 0800 917 901 India 800 440 1468

Argentina +54 11 4837

7000

Germany 0800 182

5347

Pakistan 888 550 2682

Brazil +55 15 3413

8000

Italy 8008 77334 China +86 21 2892

9000

Venezuela +58 26 1731

3446

Central &

Eastern

+41 (0) 41

7686 111

Japan +81 3 5769

6803

Russia/CIS +7 495 995

9559

South Korea +82 2 3438

4600

Egypt 0800 000

0015

Singapore +65 6 777

8211

Oman 800 70101 Thailand 001 800 441

6426

Qatar 431 0044 Malaysia 800 814 008

Kuwait 663 299 01

South Africa 800 991 390

Saudi Arabia 800 844 9564

UAE 800 0444

0684

Quick Start Guide November 2019

4 Rosemount™ 8782 Slurry Magnetic Flow Meter Transmitter

3 Pre-installation

Before installing the transmitter, there are several pre-installation steps that

should be completed to make the installation process easier:

•Identify options and configurations that apply to your application

•Set the hardware switches if necessary

•Consider mechanical, electrical, and environmental requirements

Note

Refer to the product reference manual for more detailed requirements.

Identify options and configurations

The typical transmitter installation includes a device power connection, a

4-20mA output connection, and sensor coil and electrode connections.

Other applications may require one or more of the following configurations

or options:

•Pulse output

•Discrete input/discrete output

•HART multidrop configuration

The transmitter may have up to four user-selectable hardware switches.

These switches set the alarm mode, internal/external analog power,

internal/external pulse power, and transmitter security. The standard

configuration for these switches when shipped from the factory is as follows:

Table 3-1: Hardware switch default settings

Setting Factory configuration

Alarm mode High

Internal/external analog power Internal

Internal/external pulse power External

Transmitter security Off

The analog power switch and pulse power switches are not available when

ordered with intrinsically safe output, ordering code B.

In most cases, it is not necessary to change the setting of the hardware

switches. If the switch settings need to be changed, refer to the product

reference manual.

Be sure to identify any additional options and configurations that apply to

the installation. Keep a list of these options for consideration during the

installation and configuration procedures.

November 2019 Quick Start Guide

Quick Start Guide 5

Mechanical considerations

The mounting site for the transmitter should provide enough room for

secure mounting, easy access to conduit entries, full opening of the

transmitter covers, and easy readability of the Local Operator Interface (LOI)

screen (if equipped).

Quick Start Guide November 2019

6 Rosemount™ 8782 Slurry Magnetic Flow Meter Transmitter

Figure 3-1: Rosemount 8782 Dimensional Drawing

9.0

(229)

2.8

(71)

3.1

(79)

3.5

(89)

12.0

(306)

17.7

(449)

11.4

(289)

1.6

(40)

3.9

(99)

1.9

(49)

1.7

(43)

1.9

(49)

7.8

(198)

11.2

(283)

A. Conduit entry, ½–14 NPT (4 places)

B. Ground lug

C. LOI keypad cover

D. Lower cover opens for electrical connections

Note

Dimensions are in inches (Millimeters)

Electrical considerations

Before making any electrical connections to the transmitter, consider

national, local, and plant electrical installation requirements. Be sure to have

November 2019 Quick Start Guide

Quick Start Guide 7

the proper power supply, conduit, and other accessories necessary to

comply with these standards.

The transmitter requires external power. Ensure access to a suitable power

source.

Table 3-2: Electrical Data

Electrical data

Power input AC power:

90–250 VAC ( ), 1.5A, 120 VA

Standard DC power:

12–42 VDC ( ), 8.6 A, 120 W

Pulsed circuit Internally powered (Active): Outputs up

to 12 VDC, 12.1 mA, 73 mW

Externally powered (Passive): Input up to

28 VDC, 100 mA, 1 W

4-20mA output circuit Internally Powered (Active): Outputs up

to 25 mA, 24 VDC, 600 mW

Externally Powered (Passive): Input up to

25 mA, 30 VDC, 750 mW

Um 250 V

Coil excitation output 2.0 A, 85 V max, 80 W max

Environmental considerations

Remote mounted transmitters may be installed in the control room to

protect the electronics from the harsh environment and to provide easy

access for configuration or service.

Table 3-3: Transmitter housing environmental ratings

Type Rating

Ingress protection IP66, IP69

NEMA 4X

Pollution Degree 2

Maximum altitude rating •13,123 ft (4000 m) at rated input

power voltage (90–250 VAC)

•16,404 ft (5000 m) at maximum

input power voltage of 150 VAC

Note

For complete environmental and other specifications, refer to the product

reference manual.

Quick Start Guide November 2019

8 Rosemount™ 8782 Slurry Magnetic Flow Meter Transmitter

4 Mounting

Wall mount transmitters are shipped with mounting hardware for use on a

2 inch (50 mm) pipe or flat surface.

Figure 4-1: Mounting bracket

A. U-bolt

B. Fasteners

4.1 Pipe mounting

1. Assemble the hardware and transmitter housing on the pole as

shown in Figure 4-1.

2. Tighten the nuts to ensure a snug fit.

November 2019 Quick Start Guide

Quick Start Guide 9

4.2 Surface mounting

Attach the transmitter to the mounting location using customer supplied

mounting screws. The installation of the transmitter shall be rated for four

(4) times the weight of the transmitter or 44lbs (20kgs).

Quick Start Guide November 2019

10 Rosemount™ 8782 Slurry Magnetic Flow Meter Transmitter

Andere Handbücher für Rosemount 8782

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 644 HART Bedienungsanleitung

Emerson

Emerson Rosemount 3408 Bedienungsanleitung

Emerson

Emerson Rosemount 8732E Bedienungsanleitung

Emerson

Emerson Rosemount 1066 Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Konfigurationshandbuch

Emerson

Emerson Fisher FIELDVUE 4400 Bedienungsanleitung

Emerson

Emerson Micro Motion 4200 Kurzanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 708 Bedienungsanleitung

Emerson

Emerson 6081-P Bedienungsanleitung

Emerson

Emerson Rosemount 8732EM Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Micro Motion 4200 Bedienungsanleitung

Emerson

Emerson Rosemount5081 Bedienungsanleitung

Emerson

Emerson Rosemount 1408H Bedienungsanleitung

Emerson

Emerson MICRO MOTION 1500 Bedienungsanleitung

Emerson

Emerson Fisher 4200 Series Bedienungsanleitung

Emerson

Emerson Rosemount 2090P Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung