Emerson Rosemount CX1100 Bedienungsanleitung

Quick Start Guide

00825-0100-4110, Rev AB

April 2020

Rosemount™ CX1100

In Situ Oxygen Transmitter

Essential instructions

Emerson designs, manufactures, and tests its products to meet many national and international

standards. Because these instruments are sophisticated technical products, you must properly install,

use, and maintain them to ensure they continue to operate within their normal specifications. You

must adhere to the following instructions and integrate them into your safety program when

installing, using, and maintaining Emerson's Rosemount products. Failure to follow the proper

instructions may cause any one of the following situations to occur: loss of life, personal injury,

property damage, damage to this instrument, and warranty invalidation.

•Read all instructions prior to installing, operating, and servicing the product.

•If you do not understand any of the instructions, contact your Emerson representative for

clarification.

•Follow all warnings, cautions, and instructions marked on and supplied with the product.

•To ensure proper performance, use qualified personnel to install, operate, update, program, and

maintain the product.

•Use only factory documented components for repair. Tampering and unauthorized substitution

and parts can affect product performance and cause unsafe operation of your process.

•Install equipment as specified in the installation instructions of the appropriate Reference Manual

and per applicable local and national codes. Connect all products to the proper electrical and

pressure sources.

Quick Start Guide April 2020

2 Emerson.com/Rosemount

WARNING

RISK OF ELECTRICAL SHOCK

Failure to install covers and ground leads could result in serious injury or death.

Disconnect the main power wire from the separate power source before servicing.

Do not operate or energize transmitter with case open!

Wiring connected in this box must be rated at least 240 Vac and 14 gauge.

Non-metallic cable strain reliefs do not provide grounding between conduit connections! Use

grounding type bushings and jumper wires.

Seal unused cable conduit entries securely with non-flammable enclosures to provide

transmitter's enclosure integrity in compliance with personal safety and environmental protection

requirements. Seal unused conduit openings with Type 4X or IP66 conduit plugs to maintain the

ingress protection rating (Type 4X) of transmitter's enclosure.

Operate only with front panel fastened and in place.

For safety and performance, connect and properly ground the system through a three wire power

source.

Proper use and configuration is the operator's responsibility.

Install all protective equipment covers and safety ground leads after installation.

Provide local ground connection to the transmitter in order to avoid electric shock. The ground

conductor should be equal to or greater than 16 AWG for a copper conductor in free air or 12

AWG for an enclosed copper conductor.

Disconnect and lock out power before connecting the power supply.

Disconnect and lock out power before working on any electrical components. There is voltage up

to 240 Vac. Verify the reliability and continuity of the grounding of the probe connection before

powering the equipment.

To meet the Safety Requirements of IEC 61010-1 (EC requirement) and ensure safe operation of

the equipment, make a connection to the main electrical power supply through a circuit breaker

(max 10 A) which will disconnect all current-carrying conductors during a fault situation. The

circuit breaker should also include a mechanically operated isolating switch. If it does not, then

locate another means of disconnecting the supply from the equipment close by. Circuit breakers

or switches must comply with a recognized standard, such as IEC 60947.

Ensure that all equipment doors are closed and protective covers are in place, except when

maintenance is being performed by qualified people, to prevent electrical shock and personal

injury.

WARNING

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the

equipment may be impaired.

CAUTION

If the ducts will be washed down during outage, make sure to power down the probes and remove

them from the wash area.

When replacement parts are required, ensure that qualified people use replacement parts

specified by Emerson. Unauthorized parts and procedures can affect the product's performance,

place the safe operation of your product at risk, and void your warranty. Look-alike substitutions

may result in fire, electrical hazards, or improper operation.

Note

The information contained in this document is subject to change without notice.

April 2020 Quick Start Guide

Quick Start Guide 3

Symbols

Earth (ground) terminal

Protective conductor terminal

Risk of electrical shock

Refer to Reference Manual or Quick Start Guide

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end

users’ equipment. This could be intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and fundamental to protecting your

system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for

all systems used within the facility.

Contents

Install........................................................................................................................................... 5

Wire........................................................................................................................................... 17

Start up...................................................................................................................................... 22

Calibration................................................................................................................................. 23

Product certifications................................................................................................................. 25

Declaration of Conformity..........................................................................................................27

China RoHS table........................................................................................................................28

Quick Start Guide April 2020

4 Emerson.com/Rosemount

1 Install

WARNING

Failure to follow safety instructions could result in serious injury or death.

Before installing this equipment, read the Essential instructions at the front

of this Quick Start Guide.

WARNING

ELECTRIC SHOCK

Failure to install covers and ground leads could result in serious injury or

death.

Install all protective equipment covers and safety ground leads after

installation.

CAUTION

Equipment damage

Damage to the transmitter may result.

Do not allow the temperature of the probe electronics to exceed 194 °F (90

°C)

1.1 Install probe

Emerson can supply a weld plate for welding to the flue gas duct for new

installations.

Procedure

1. If using the standard square weld plate (Figure 1-2) or an optional

flange mounting plate, weld or bolt the plate onto the duct.

The through hole diameter in the stack or duct wall and refractory

material must be at least 2.5 in. (63.5 mm).

2. Insert probe through the opening in the mounting flange and bolt

through the probe gasket and flange.

For horizontal installations, the breather port must be oriented such

that it is facing downward.

April 2020 Quick Start Guide

Quick Start Guide 5

Figure 1-1: Probe Installation

All dimensions are in millimeters with inches in parentheses.

A. M6 X 1 X 25 hex head machine screw (3X)

B. Calibration gas, 4.8 mm (3/16-in.) tube fitting, 2.82 liter/minute (10

SCFH), 138 kPa (20 psig)

C. M5 X 0.8 x 10 pan head machine screw, ground screw

D. ½ national pipe thread (NPT) conduit connection (power, signal)

E. Breather port

F. Calibration gas connection

Table 1-1: Removal/Installation

Probe length Removal envelope

.5 m (19.68 in.) 750 mm (30 in.)

1 m (39.37 in.) 1250 mm (49 in.)

2 m (78.74 in.) 2250 mm (89 in.)

Quick Start Guide April 2020

6 Emerson.com/Rosemount

Figure 1-2: Probe Installation

All dimensions are in millimeters with inches in parentheses.

Square weld plate, ANSI pattern part 4512C34G01

April 2020 Quick Start Guide

Quick Start Guide 7

Table 1-2: Mounting Flange

ANSI DIN

Flange diameter 185 mm (7.28 in.)

Hold diameter 19.1 mm (.75 in.)

4 holes equally spaced on

120.7 mm (4.75 in.) 145 mm (5.71 in.)

Figure 1-3: Drip Loop and Insulation Removal

A. Note

Replace insulation after installing Rosemount CX1100.

B. Drip loop

C. Stack duct or metal wall

D. Adapter plate

E. Insulation

Note

Probe installation may be vertical or horizontal.

Quick Start Guide April 2020

8 Emerson.com/Rosemount

1.2 Mount remote display

The remote transmitter is available in a panel mounting or wall/pipe

mounting configuration.

Prerequisites

You need a wrench and bolts to mount the transmitter.

Note

Dimensions are in inches with millimeters in parentheses.

Figure 1-4: Wall/Surface Mount Front View

A. Four cover screws

April 2020 Quick Start Guide

Quick Start Guide 9

Figure 1-5: Wall Mount Side View

Quick Start Guide April 2020

10 Emerson.com/Rosemount

Andere Handbücher für Rosemount CX1100

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 1408A Bedienungsanleitung

Emerson

Emerson Rosemount 1208 Bedienungsanleitung

Emerson

Emerson Rosemount 1151 Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 644 FOUNDATION Bedienungsanleitung

Emerson

Emerson Rosemount 3051P Bedienungsanleitung

Emerson

Emerson Rosemount 2051L Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount 3308 Bedienungsanleitung

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 3100 Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 5600 Series Bedienungsanleitung

Emerson

Emerson PENBERTHY MGT-362 Handbuch

Emerson

Emerson Rosemount HART Modbus VeriCase 3308 Series Bedienungsanleitung

Emerson

Emerson Rosemount 708 Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson ROSEMOUNT 5081-A Bedienungsanleitung

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount 8712C Konfigurationshandbuch

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung