EMG EMG-HZ Series Service-Handbuch

HZ 35 40 45 INST REV 0804

EMG - 35 HZ

MAXIMUM RECOMENDED STRING SIZE 2.625

MAXIMUM RECOMENDED STRING SIZE 3.125

MAXIMUM RECOMENDED STRING SIZE 3.75

EMG - 40 HZ

EMG - 45 HZ

EMG-HZ

3.92"

3.50"

1.50"

4.00"

2.82"

3.40"

.34"

.30"

.29"

4.00"

INSTALLATION INFORMATION

EMG-HZ Models:

35HZ, 40HZ, 45HZ

Each pickup includes:

5 pin cable pre-wired in Humbucking Series format

Adjustment screws

IMPORTANT INSTALLATION NOTES:

Recommended String Width

Model 35HZ 2.75 inches 4 string or narrow 5 string

Model 40HZ 3.125 inches 5 string or narrow 6 string

Model 45HZ 3.75 inches 6 string

All EMG-HZ bass pickups feature bar style construction.

Refer to the dimensions above for maximum string width.

EMG-HZ Warranty:

All EMG-HZ Pickups and accessories are warranted for a period of two

years. This warranty does not cover failure due to improper installation,

abuse, or damage. If it any time a pickup fails to work, return it postage

prepaid with proof of purchase. If upon examination the pickup is determined

to be defective, a replacement will be mad at no charge. Warranty

replacement products are covered under this same warranty. This warranty

covers only those pickups and accessories sold by authorized EMG

Dealers.

Tone

Volume .047

.047

Bridge pickup cable

EMG-HZ Diagram 6

2 Volume, 2 Tone w/switch

(each Volume is independent)

Finger Board pickup cable

BLACK

WHITE

Bottom View

Tone

.047

Volu me

Fingerboard pickup cable

EMG-HZ Diagram 7

1 Volume, 1 Tone

w/ 3 position lever switch

BLACK

WHITE

Bridge pickup cable

Bottom View

Volume

0230-0043B

Passive Installations:

The HZ Pickups will work with either 250K Ohm or 500K Ohm pots (Audio Taper)

and a tone capacitor value of .047 microfarad. 500K Ohm pots provide a slight

up-shift of resonant frequency and approx. 3dB more gain at resonance and are

recommended for Dual-Coil Pickups.

A note about string grounding:

Although the EMG-HZ Pickups are shielded, they still require string grounding,

especially the A(Alnico) models. String grounding uses your body as a shield to

help in reducing hum and buzz from the pickup. It also can create a shock hazard

due to mis-matched polarities. Be sure to make sure your guitar is electrically in

phase with any microphones as well as other players instruments.

Wiring Legend:

The legend for the coils and wire colors are shown on the bottom of the pickup.

Legend Wire Color Coil Polarity

G 1- Green 1 Negative

W 1+ White 1 Positive

GND GROUND SHIELD

R 2- Red 2 Negative

B 2+ Black 2 Positive

Installation for EMG-HZ Models: 35HZ, 40HZ, 45HZ

Tone

Volume Volume

Bridge pickup cable

EMG-HZ Diagram 2

2 Volume, 1 Tone

(each Volume is independent)

Finger Board pickup cable

.047

Bottom View

ToneVolume .047

EMG- HZ Diagram 1

1 Volume, 1 Tone

EMG-HZ Pickup cable

WHITE

Bottom View

Tone

.047

Vol ume

Fingerboard pickup cable

EMG-HZ Diagram 3

1 Volume, 1 Tone w/switch

BLACK

WHITE

Bridge pickup cable

Bottom View

Tone

Volume

Bridge pickup cable

EMG-HZ Diagram 4

2 Volume, 1 Tone w/switch

(each Volume is independent)

Finger Board pickup cable

WHITE

BLACK

.047

Bottom View

Volume

Dieses Handbuch passt für folgende Modelle

Beliebte Zubehör für Musikinstrumente Handbücher anderer Marken

Behringer

Behringer AIRPLAY GUITAR AG10 Bedienungsanleitung

FEURICH

FEURICH BASIC Bedienungsanleitung

thomann

thomann Harley Benton JA Bedienungsanleitung

NeoTech

NeoTech PAD-IT TUBA HARNESS Bedienungsanleitung

Duncan

Duncan SH-8n Invader Kurzanleitung

Palmer

Palmer The Junction PDI-09 Bedienungsanleitung

GuitarPCB

GuitarPCB Fuzzy Bee v2 Handbuch

Yamaha

Yamaha Tough-Terrain T-335 Bedienungsanleitung

LEWISMIDI

LEWISMIDI CZ Patch Library Bedienungsanleitung

Free The Tone

Free The Tone LB-2 Bedienungsanleitung

Duncan

Duncan Apollo Jazz Bass - neck Handbuch

dbx

dbx dB10 Bedienungsanleitung

TLA

TLA Tuning-Set CTS-32-C Bedienungsanleitung

Solo Music Gear

Solo Music Gear JEK-1 Bedienungsanleitung

Duncan

Duncan HyperSwitch Bedienungsanleitung

CNC Design

CNC Design QUAD COIL WINDER MK2 Bedienungsanleitung

FuzzDog

FuzzDog 3PDT Bedienungsanleitung

Hipshot

Hipshot Universal Mounting Plate Bedienungsanleitung