Emos P5805 Bedienungsanleitung
1911000050_31-P5805_00_01 95 × 127 mm
www.emos.eu
P5805
GB Digital Power Meter
CZ Digitální měřič spotřeby elektrické energie
SK Digitálny merač spotreby elektrickej energie
PL Watomierz cyfrowy
2
3
GB | Digital Power Meter
Device description
The power consumption metre P5805 (hereinafter referred to as metre) is an electronic
device which measures power consumption and can also calculate and display operating
costs of the measured appliance on agraph. The graph can be set up to display the last 7
days/weeks/months. This function allows the user to reduce power costs and decrease
CO2emissions.
Specications:
Nominal voltage: 230–240 V~/50 Hz
Nominal current: max. 16 A
Max. load: 3 680 W
Operating voltage: 175–276 V~/50 Hz
Period recorded: 0 sto 9 999 days
Operating temperature: 0–50 °C
Measuring range: 2 to 3 680 W
Power consumption range: 0 kWh to 9 999 kWh
Battery: 2× 1.5 V (LR44/AG13)
Use in normal dry conditions with relative humidity ranging from 20 to 90 %
Connection: First, remove the plastic ring from the battery space at the
rear of the metre, as shown in the picture. The installed
batteries 2× 1.5V (LR44/AG13) are used to power the metre
memory.
Then, connect the metre to a230 V~ power network. Do
not connect any appliance to the metre yet. If the display
of the metre does not show any data or the data is dicult to read, press the „RESET“
button using asharp pointy object such as apen or apencil. Then, the screen will display
all characters as shown on the gure below. This display will remain for ca 3 seconds.
2
3
Display settings:
1. current time setup
1.1 Press and hold the „SET/OK“ button for 3 seconds. You will enter the settings mode
and the clock icon will start blinking. You can change the time values using the buttons
„ENERGY/+“ (increasing values) or „COST/-“ (decreasing values). Pressing the „HISTORY“
button will switch between hours and minutes. Once current time is set, press „SET/OK“.
Switching to 12/24 hour mode
After setting the current time, the metre will work on a24 hour time cycle. If you want
to switch to 12 hour mode, simultaneously hold the „HISTORY“ and „ENERGY/+“ buttons
for 3 seconds. The display will show the AM or PM symbol. AM indicates morning hours,
PM afternoon hours. Set the desired time mode (12/24).
1.2 Total operating time of the connected appliance (TOTAL TIME):
Once the load (input power of the connected appliance) exceeds 2 W, total time will
start recording automatically. You can display the total operating time by pressing the
„COST/-“ button.
1.3 using the „COST/-“ button, the display will show the following, in order:
• Total operating time
• Total power consumption 0.00–9 999 kWh
• Total power costs 0.00–9 999 EUR
4
5
• Power costs in tari 1 (0.00 EUR/kWh – 9 999 EUR/kWh)
• Tari 1 start time
• Power costs in tari 2 (0.00 EUR/kWh – 9 999 EUR/kWh)
• Tari 2 start time
• CO2volume in kg: 0.00 – 9 999 kg CO2/kWh
• Total CO2consumption in kg 0.00 – 9 999 kg
2. Setting power current tari
Keep pressing the „COST/-“ button until you reach the power current tari settings.
4
5
Hold the „SET/OK“ button for 3 seconds. „DUAL TARIFF“ will start blinking. Again press
„SET/OK“ – use the „HISTORY“ button to change the number, then press „ENERGY/+“ or
„COST/-“ to set arange between 0.00 EUR/kWh and 9 999 EUR/kWh; you can move between
numbers using the „HISTORY“ button. Finally, press „SET/OK“ to conrm the set values.
2.1 Setting power current tari 1 time
After setting the tari values, the screen will show „TIME START“
Press the „HISTORY“ button and select which value you want to change. By pressing
„ENERGY/+“ or „COST/-“, you can increase or decrease the values. When you are done,
press „SET/OK“.
2.2 Setting power current tari 2
To set up power current tari 2, proceed as described in points 2 and 2.1
Note:
If dual tari is set, tari 1 will start from the set time and turn o when the set time for
tari 2 comes. Current tari 2 will end the moment tari 1 begins.
3. Overload settings
Hold the „ENERGY/+“ button for 3 seconds; the top left corner of the screen will now
display „OVERLOAD“. Then, using the „HISTORY“ button, move between values and set the
maximum load. The default setting is 3 680 W. You can save the settings by pressing „SET/
OK“. After exceeding the set value, the „OVERLOAD“ sign will start blinking.
4. Setting CO2:
Keep pressing „COST/-“ until you reach the following screen.
6
7
Then hold the „SET/OK“ button for 3 seconds. Using the „HISTORY“ button, move between
values. „ENERGY/+“ and „COST/-“ increase/decrease the values. You can save the settings
by pressing „SET/OK“.
5. Consumption graph for the last 7 days/weeks/months
Using the „HISTORY“ button, you can change display settings to the last 7 days, 7 weeks
or7months.
7 days
the top right corner of the graph shows the conversion ratio, indicating the power con-
sumed. In this case, each bar corresponds to 1 kWh, i.e. yesterday, power consumption
was 2 kWh (1 kWh × 2 bars)
7 weeks
the top right corner of the graph shows the conversion ratio, indicating the power con-
sumed. In this case, each bar corresponds to 20 kWh (2 kWh × 10), i.e. last week, power
consumption was 60 kWh (20 kWh × 3 bars)
7 months
the top right corner of the graph shows the conversion ratio, indicating the power con-
sumed. In this case, each bar corresponds to 50 kWh (5 kWh × 10), i.e. last month, power
consumption was 100 kWh (50 kWh × 2 bars)
The individual power consumption values shown using bars are:
1BAR = 1 kWh
1BAR = 2 kWh
1BAR = 3 kWh
1BAR = 5 kWh
1BAR = 1 kWh × 10 (10 kWh)
1BAR = 15 kWh
1BAR = 2 kWh × 10 (20 kWh)
1BAR = 3 kWh × 10 (30 kWh)
1BAR = 5 kWh × 10 (50 kWh)
6
7
6. Actual consumption in days/weeks/ months
6.1 Actual power consumption in the last 7 days:
Hold the „HISTORY“ button for 3 seconds once the screen shows the „daily“ value.
Press „ENERGY/+“ or „COST/-“ to select the day you want to show. Display -1 means
yesterday, -2 two days ago etc. up to -7 aweek back. The real power consumption is
shown on the second line.
6.2 Actual power consumption in the last 7 weeks:
Hold the „HISTORY“ button for 3 seconds once the screen shows the „weekly“ value.
Press „ENERGY/+“ or „COST/-“ to select the week you want to show. -1 indicates last
week, -2 two weeks ago etc. up to -7 seven weeks ago. The real power consumption is
shown on the second line.
6.3 Actual power consumption in the last 7 months:
Hold the „HISTORY“ button for 3 seconds once screen shows the „monthly“ value.
Press „ENERGY/+“ or „COST/-“ to select the month you want to show. -1 indicates last
month, -2 two months ago etc. up to -7 seven months ago. The real power consumption
is shown on the second line.
7. Quickly deleting data
7.1 Press and hold „ENERGY/+“ and „COST/-“ simultaneously for 3 seconds, until the
screen starts blinking.
7.2 Then press and hold „SET/OK“ for 3 seconds. All the data will be erased.
8. Replacing batteries
8.1 Open the battery compartment cover on the back side of the consumption metre.
8
9
8.2 Remove the at batteries.
8.3 Insert new 2× 1.5 V (LR44/AG13) batteries. Make sure you observe the correct polarity.
Use alkaline batteries only, not rechargeable ones.
8.4 Close the cover.
Safety warning
• Connect the metre to a230 V~/50 Hz (±10 %), max. 16 Anetwork tted with asafety
switch/contact.
• Only appliances powered by 230 V~/50 Hz voltage can be connected to the metre.
• Pay attention to the data on the type label of the appliances connected to the device.
• The maximum input power of the connected appliances must not exceed 3 680 W
(max. current 16 A).
• Use the metre in closed spaces and dry environments only. Using the metre outdoors
is strictly forbidden!
• The screen is powered using alkaline batteries. Do not recharge, short circuit or destroy
the batteries or throw them in are. Do not combine new and old batteries, dierent
types, systems or brands. Remove the batteries if the device is not used for alonger
period of time. Store the batteries out of range of children.
• Any use of the device which is not listed in the previous sections of this manual will
lead to damaging the product and can create arisk of short circuiting, injury by electric
current etc. The metre must not be altered or otherwise restructured! Safety warnings
must be followed unconditionally.
• We take no responsibility for material damage and injury to persons caused by improper
use of the metre or disregard of instructions and safety warnings listed in the manual.
Any claim for warranty is voided in these cases.
• Make sure that the lead-in protective conductor is not disrupted – the life of the user
may be endangered if the protective conductor is disrupted.
• Recommended ambient temperature of the operation of the metre is 0 °C to +50
°C. Higher temperatures, especially when measuring larger appliances, can lead to
overheating and permanent damage or destruction of the metre.
• The metre must only be used in areas with no danger of unfavourable operating
conditions such as ammable gasses, vapours and dust.
• For safety reasons, never use the metre when wet or in awet environment.
• When cleaning or maintaining the device, the device must always be disconnected
from lead-in power supply. The capacitors in the device may still be charged, especially
if the devices was only disconnected from voltage recently.
• In schools and education institutes, interest workshops and self-help workshops,
the use of the device is permitted only under the supervision of qualied personnel.
• Do not insert needles or other metal or conductive instruments into the device.
• If the device is used in amanner not specied by the manufacturer, the protection
provided by the device may become damaged.
• Regularly check the P5805 device for damage.
• Any maintenance or repair of the device must be performed by atrained professional
electrical engineer who is demonstrably familiar with the corresponding safety and
electrical engineering regulations.
8
9
• When cleaning the device and the LCD screen, only use asoft dry cloth. Do not use
any cleaning agents or immerse the device in water!
• This appliance is not intended for use by persons (including children) whose physical,
sensory or mental disability or lack of experience and expertise prevents safe use,
unless they are supervised or instructed in the use of the appliance by aperson
responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
Do not dispose with domestic waste. Use special collection points for sorted waste.
Contact local authorities for information about collection points. If the electronic
devices would be disposed on landll, dangerous substances may reach ground-
water and subsequently food chain, where it could aect human health.
CZ | Digitální měřič spotřeby elektrické energie
Popis přístroje
Měřič spotřeby P5805 (dále jen měřič) je elektronické zařízení, které měří spotřebovanou
elektrickou energii azároveň dokáže vypočítat azobrazovat náklady na provoz měřeného
zařízení pomocí grafu. Na grafu je možné nastavit posledních 7 dní/týdnů/měsíců. Tato
spotřeba pomáhá uživatelům snižovat náklady na elektrickou energii azároveň snižovat
emise CO2.
Technické údaje:
Jmenovité napětí: 230–240 V~/50 Hz
Jmenovitý proud: 16 Amax.
Max. zatížení: 3 680 W
Pracovní napětí: 175–276 V~/50 Hz
Zaznamenaný čas: 0 saž 9 999 dní
Provozní teplota: 0–50 °C
Měřicí rozsah: 2 až 3 680 W
Rozsah spotřeby el. energie: 0 kWh až 9 999 kWh
Baterie: 2× 1,5 V (LR44/AG13)
Použití do normálního suchého prostředí srozsahem relativní vlhkosti od 20 % do 90 %
Připojení: Nejprve odstraňte plastový proužek zbateriového prostoru
na zadní straně měřiče dle obrázku. Instalované baterie
2×1,5V (LR44/AG13) slouží pro napájení paměti měřiče.
Poté připojte měřič do elektrické sítě 230 V~ ak měřiči zatím
nepřipojujte žádný spotřebič. Jestliže se na displeji měřiče
nezobrazí žádné údaje nebo jsou špatně čitelné, stiskněte
tlačítko „RESET“ pomocí ostrého hrotu jako je pero nebo tužka. Poté se na displeji zobrazí
všechny znaky jako na obrázku níže. Zobrazení potrvá po dobu cca 3 vteřin.
10
11
Nastavení displeje:
1. nastavení aktuálního času
1.1 Stiskněte tlačítko „SET/OK“ na dobu 3 vteřin, jste v módu nastavení a začne blikat ikona
hodin. Hodnoty času změníte pomocí tlačítek „ENERGY/+“ (do zvyšujících hodnot) nebo
„COST/-“ (do snižujících hodnot). Stisknutím tlačítka „HISTORY“ přepínáte mezi hodinami
a minutami. Jakmile máte nastaven aktuální čas, zmáčkněte tlačítko „SET/OK“.
Nastavení 12/24hodinového režimu
Po standardním nastavení aktuálního času na měřiči je nastaven 24hodinový cyklus času.
Pokud chcete 12hodinové zobrazení, podržte současně tlačítka „HISTORY“ a „ENERGY/+“
po dobu 3 vteřin. Na displeji se objeví symbol AM nebo PM. AM je dopolední zobrazení
času, PM je odpolední zobrazení času. Nastavte vámi požadovaný hodinový režim (12/24).
1.2 Celkový čas provozu připojeného spotřebiče (TOTAL TIME):
Jakmile je zátěž (příkon připojeného spotřebiče) větší než 2 W, automaticky začne načítání
času. Zobrazení času provozu aktivujete pomocí stisknutí tlačítka „COST/-“.
1.3 pomocí tlačítka „COST/-“ se postupně na displeji zobrazuje:
• celkový čas provozu
• celková spotřeba elektrické energie 0,00–9 999 kWh
Andere Handbücher für P5805
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Emos Messgerät Handbücher
Emos
Emos M0501 Bedienungsanleitung
Emos
Emos M0501 Bedienungsanleitung
Emos
Emos E0345 Bedienungsanleitung
Emos
Emos FHT 9999 Bedienungsanleitung
Emos
Emos FHT-9998 Bedienungsanleitung
Emos
Emos P5821 Bedienungsanleitung
Emos
Emos P5801 Bedienungsanleitung
Emos
Emos 440L Bedienungsanleitung
Emos
Emos P5805 Bedienungsanleitung
Emos
Emos KFZ02S-05 Bedienungsanleitung
