EMR BDAMON02-MODEM Bedienungsanleitung

BDAMON02-MODEM

Bi-Directional Power Amplifier Monitor

EMR CORPORATION

17431 N. 25th Avenue - Phoenix, Arizona 85023

Phone: (623) 581-2875 - Toll Free: (800) 796-2875 - Fax: (623) 582-9499

sales@emrcorp.com – www.emrcorp.com

USERS MANUAL

Rev. 7

Table of Contents

BDAMON02-MODEM Manual – V3.D1

BDAMON02-MODEM

Introduction and Features

System Requirements

Physical Connectivity

Programming the BDA Monitor

Using Menus

Programming the Com Port

Setup Menu

Alarm Menu

Misc. Menu

Data String

Password Menu

Auto Dialer Menu

Modem Setup Menu

View Current Readings & Alarms

Resetting Alarms

Clock Setup

Hookup Diagram

Programming Flow Chart

U.S. FCC Part 68 Statement

.........................................................1

.............................................................1

..............................................................2

.....................................................3

......................................................................4

.......................................................4

.......................................................................5

.......................................................................6

.........................................................................7

....................................................................7

..................................................................8

..............................................................8

..................................................9

..................................................................9

.......................................................................9

.................................................................10

.........................................................10

......................................................11

BDAMON02-MODEM USERS MANUAL

BDAMON02-MODEM Manual – V3.D1

Introduction

The EMR BDA Monitor (Model #BDAMON02-MODEM) is a microprocessor-controlled unit

capable of monitoring the Primary AC, Power Supply/Battery DC Voltage, and the DC

Current for up to four RF amplifiers used in any EMR Signal Enhancement System. BDA

monitoring features vary depending on the relevant hardware configuration. This

documentation covers features which are common to most users.

Product Features:

• Monitoring for up to four RF Power Amplifiers

• Programmable using a standard terminal program direct or modem

• User programmable alarm set points

• 1 Relay Output Contact Closure

• Auto Dialer and 9600 Baud Modem

• LED Status Indicators

• AC Alarm

• Door Alarm

System Requirements:

• EMR Signal Enhancement Bi-Directional System

• IBM compatible computer with Com Port

• HyperTerminal or similar communication software package

• Standard Serial Cable

2BDAMON02-MODEM Manual – V3.D1

BDAMON02-MODEM USERS MANUAL

Physical Connectivity

The BDA monitor comes pre-installed in an EMR Bi-Directial Amplifier (BDA) system. When

the BDA system is plugged into a reliable power source the power indicators on the monitor

unit will light/glow. Connect the telephone line included to the RJ11 cable to the port located

at the base of the BDA enclosure.

The door alarm switch triggers an audible and LED alarm as the door opens. The alarm

must be reset from the web interface or reset button on the front of the monitoring unit before

the door is closed and the hysteresis period has lapsed.

Power Amplifier #1

Amplifier Connections

(J1 Plug)

Power Amplifier #2

Door Alarm Switch

Phone Line

COM Port

Power Amplifier #1

Amplifier Connections

(J1 Plug)

Power Amplifier #2

Door Alarm Switch

Phone Line

COM Port

BDAMON02-MODEM USERS MANUAL

BDAMON02-MODEM Manual – V3.D1

Programming the BDA Monitor

Open your communications software such as HyperTerminal in your computer. Set up a

COM port at 19200 baud 8, n, 1 flow control: none. Connect a serial cable from the COM

port of your computer to the DB-9 port of the BDA Monitor.

The BDA Monitor’s programming proceeds through a hierarchy of menus.

Press <Enter> once on your computer. The following screen should appear:

Fig. 1

The default password is “123456”. Enter this to load the Main Menu screen.

Fig. 2

Enter Password >

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Main Menu

Select The Following

A>> Com Port Setup

B>> Alarm and Misc. Setup

C>> Auto Dialer Setup

D>> Modem Setup

E>> View Current Readings & Alarms

F>> Reset Alarms

G>> Clock Setup

X>> Exit

4BDAMON02-MODEM Manual – V3.D1

BDAMON02-MODEM USERS MANUAL

Using Menus

A menu option is selected by pressing the corresponding letter. For example to load the

Alarm and Misc. Setup Menu, press “B” in the “Main Menu“. In the “Setup Menu” press “X” to

return to the “Main Menu” screen.

Programming the Com Port

Press “A” from the “Main Menu” to display the “Com Port Menu”. Fig. 3 indicates the current

Baud Rate as 19200.

Fig. 3

Choose the desired Baud rate or type in a custom setting. By pressing “A” the Baud Rate will

change to 9600.

Fig. 4

Note: The current Baud rate remains until the user exits the programming mode.

Press “X” to exit and return to the main menu.

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Com Port Menu

Select The Following

A>> Current Baud Rate: 19200

X>> Exit

A>> 9600 Baud

B>> 19200 Baud

Enter New Setting [X to Exit] >

BDAMON02-MODEM USERS MANUAL

BDAMON02-MODEM Manual – V3.D1

Setup Menu

Pressing “B” from the “Main Menu” displays the “Setup Menu”. This menu displays the

following options:

• Change Alarm Set points

• Change Miscellaneous Settings

• Change the Password

Fig. 5

Alarm Menu

Pressing “A” from the “Setup Menu” displays the “Alarm Setup” menu (Fig. 6). This menu the

displays the following options:

• Change the four Amp Low and High Current Alarms

• Change the DC Voltage Low and High Alarms

• Enable or Disable the AC Sense Alarm

• Enable or Disable the Door Alarm

• Enable or Disable the Audible Alarm

Fig. 6

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Setup Menu

Select The Following

A>> Alarm Menu

B>> Misc. Menu

C>> Password Setup

D>> Modem Setup

E >> Current Readings & Alarms

F >> Reset Alarm

G>> Clock Setup

X>> Exit

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Alarm Setup

Select The Following

A>> Amp #1 Current Low Alarm = Disabled

B>> Amp #1 Current High Alarm >=Disabled

C>> Amp #2 Current Low Alarm = Disabled

D>> Amp #2 Current High Alarm >=Disabled

E>> Amp #3 Current Low Alarm = Disabled

F>> Amp #3 Current High Alarm >=Disabled

G>> Amp #4 Current Low Alarm = Disabled

H>> Amp #4 Current High Alarm >=Disabled

I>> DC Voltage Low Alarm <=12.00 Vdc

J>> DC Voltage High Alarm >=14.90 Vdc

K>> AC Alarm =Disabled

L>> Door Alarm=Disabled

M>> Audible Alarm=Disabled

X>> Exit

6BDAMON02-MODEM Manual – V3.D1

BDAMON02-MODEM USERS MANUAL

Alarm Menu (continued)

From this screen the user can either view the current settings or edit.

For example, to change the “Amp #1 Current Low Alarm” press the “A” key and the “Current

Amp #1 Low Alarm” is displayed followed by the “Enter New Setting” prompt.

Fig. 7

To disable or enable a port press “D” to disable the alarm or “E” to enable.

Enter the new setting and press <Enter> or “X” to Exit.

Misc. Menu

Press “B” from the “Setup Menu” to display the “Misc. Setup” menu (Fig. 8). This menu

displays the following options:

Fig. 8

Note: Options A, B & C are factory settings and not user changeable.

Current Amp #1 Low Alarm <= 0.20 Amps

Enter New Setting

[D to Disable E to Disable X to Exit] >

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Misc. Setup

Select The Following

A>> Recalibrate Unit

B>> Recalibrate Counter = 0

C>> TP-1 Voltage = 13.60

D>> Hysteresis (0 to 255) = 10

E>> Data String = Disabled

X>> Exit

BDAMON02-MODEM USERS MANUAL

BDAMON02-MODEM Manual – V3.D1

Data String

Changing the “E” Data String line to “Enabled” will send a comma delimited string in the

following format out the Com Port.

Time: Date, Door, Door Alarm, DC Voltage, DC Alarm, AC, AC Alarm, Port#1 Current, Port#1 Alarm,

Port#2 Current, Port#2 Alarm, Port#3 Current, Port#3 Alarm, Port#4 Current, Port#4 Alarm

For Example:

14:42:9/28/2010, 0, 0, 13.80, 0, 0, 0, 0.25, 0, 1.20, 0, 0.27, 0, 0.00,1

Translates to:

14:42:9,9/28/2010, Door Closed, no alarm, 13.80 VDC, no alarm, AC on, no alarm, 0.25

Amps on Amp #1, no alarm, 1.20 Amps on Amp #2, no alarm, 0.27 Amps on Amp #3, no

alarm, 0.00 Amps on Amp #4, alarm on

Password Menu

Press “C” from the “Setup Menu” to display the “Password Setup” menu (Fig. 9). This menu

displays the following option:

Fig. 9

Press “A” to change the password.

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Password

Select The Following

A>> Password = 123456

X>> Exit

8BDAMON02-MODEM Manual – V3.D1

BDAMON02-MODEM USERS MANUAL

Auto Dialer Menu

Press “C” from the Main Menu to display the “Auto Dialer Setup” (Fig. 10). This menu

displays the following options:

• Change the Auto Dialer telephone numbers (2 available)

• Disable telephone #1 or telephone #2 or both telephone numbers

• Set the length of call from 15 to 60 seconds

• Enable or Disable Hourly Alarms

Fig. 10

Note: To dial a numeric pager use “,” to pause the output for 2 seconds before the next digit

is sent. For example: 1-555-555-5555,,,,,12345 dials 1-555-555-5555 then waits 10 seconds

then dials 12345.

Modem Setup Menu

Press “D” from the Main Menu to display the “Modem Setup” (Fig. 11). This menu displays

the following options:

• Select a Modem Baud Rate from 1200, 2400,4800 and 9600.

• Auto Answer from 0 to 255 Rings. Inputting “0” turns off auto answer.

Fig. 11

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Auto Dialer Setup

Select The Following

A>>Telephone Number 1 = 7678900

B>>Telephone Number 2 = 7671111

C>>Length of Call = 15

D>> Redial Hourly Alerts = Disabled

X>> Exit

************************************************

EMR Corp. BDAMON2MODEM V1.021

************************************************

Modem Setup

Select The Following

A>> Modem Baud Rate = 9600 Baud

B>> Auto Answer = 1 Ring

X>> Exit

Inhaltsverzeichnis

Andere EMR Verstärker Handbücher

EMR

EMR BDAMON02-NFPA72 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung