EMS 53-5414 Technische Daten

5000

VHF & UHF

REMOTE RECEIVERS

INSTALLATION AND PROGRAMMING

INSTRUCTIONS

MODEL NUMBERS

53 -5414 & 53 –5428

EMS 5000 FIREPOINT

Table of Contents

Section Page No

1. INTRODUCTION ................................................................................................ 3

2. TOOLS & TEST EQUIPMENT ................................................................................ 4

3. RECEIVER POSITION ......................................................................................... 4

4. UHF REMOTE RECEIVER RELEVANT HIGH GAIN AERIALS ....................................... 4

5. VHF REMOTE RECEIVER RELEVANT HIGH GAIN AERIALS ....................................... 5

6. ELECTRICAL INSTALLATION ............................................................................... 5

6.1 UHF REMOTE RECEIVER.............................................................................................................................................5

6.2 VHF REMOTE RECEIVER .............................................................................................................................................6

7. SOFTWARE CONFIGURATION ............................................................................. 7

8. MAIN CONTROL PANEL ENGINEERS MENU STRUCTURE.........................................11

9. TESTING THE SYSTEM ......................................................................................12

10. CONTROLLER INFORMATION ...........................................................................15

EMS 5000 FIREPOINT

1. Introduction

The Remote Receivers used for connection to the EMS 5000 FirePoint Control Panel are

detailed in the following instructions. Two types of remote receiver can be used with the

system, both of which are hardwired to the Control Panel via 2 core screened cable.

The Model 53-5428 is a UHF remote receiver capable of receiving UHF signals from a

number of transponder units on site. The transponder units are wireless devices, which

receive information from detectors and then re-transmit this information to the UHF

remote receiver, thus improving the overall range coverage of the system. This

information is then sent to the control panel via cable (FP200). A maximum of 28 remote

receivers can be connected to the Control Panel. A block diagram of a system using the

UHF remote receiver is shown in Figure 1.

The Model 53-5414 is a VHF remote receiver capable of receiving VHF signals directly

from all types of detectors, thus improving the overall range coverage of the system.

This information is then sent to the control panel via cable (FP200). A maximum of 28

remote receivers can be connected to the Control Panel. A block diagram of a system

using the VHF remote receiver is shown in Figure 2.

Figure 1

UHF Remote

Radio Receiver

Transponder Unit

Fire Detection

Device

Transmissions

(i.e.

Call points/

Smoke &

Heat

Detectors/

Sounders).

UHF Data

Transmitting

Aerial

VHF Data

Receiving

Aerial

UHF Data

Transmitting

Aerial

EMS 5000 FIREPOINT

2. Tools & Test Equipment

Only standard hand tools are required to install the Remote radio receiver system. No

special test equipment is needed when installing the receiver, although signals from

devices can be seen if a computer with a terminal programme is connected to the

system.

This gives a visual indication that the remote receivers are passing device data to the

main control panel.

3. Receiver Position

The maximum range between remote receiver and any device is dependant upon the

environment in which the system is operating. The actual range achieved is determined

by local site conditions. For range improvements high gain aerials can be attached to the

remote receivers. The table below indicates relevant aerials:-

4. UHF Remote Receiver Relevant high gain aerials

5-5501/High gain aerial c/w 3 metres of cable and bracket.

5-5501/BP10/High gain aerial c/w 10 metres of cable, wall mounting bracket and

extension pole.

5-5501/BP20/High gain aerial c/w 20 metres of low loss cable, wall mounting bracket

and extension pole.

5-5501/BP30/High gain aerial c/w 30 metres of low loss cable, wall mounting bracket

and extension pole.

Figure 2

VHF Remote Radio

Receiver

VHF Data

Receiving

Aerial

Fire Detection Device

Transmissions (i.e.

Call points/ Smoke &

Heat Detectors/

Sounders).

VHF Data

Receiving

Aerial

UHF Data

Transmitting

Aerial

EMS 5000 FIREPOINT

5. VHF Remote Receiver Relevant high gain aerials

5-5500/Dipole aerial c/w 10 metres of cable and bracket.

5-5500/10 High gain external aerial c/w 10 metres of cable, wall mounting bracket and

extension pole.

5-5500/20 High gain external aerial c/w 20 metres of low loss cable, wall mounting

bracket and extension pole.

When selecting a site for the receiver, the installing engineer should be aware that the

aerial should be as far away from other electrical / electronic equipment as possible and

a minimum of 3 metres from any such equipment. Locating the receiver closer than this

will affect the systems performance. Metal objects such as filing cabinets, pipe work,

radiators and air conditioning ducts will also adversely affect the performance of the

system if they are too near the receiver antenna.

6. Electrical Installation

6.1 UHF Remote Receiver

The UHF remote receiver 53-5428, should be wired as shown in the supplied drawing

PO3045.

The following paragraphs outline the installation in a step by step format.

Remove the four lid retaining screws situated on the front cover. The front section of the

unit can now be removed.

Four fixing holes are available for the unit’s installation. These are clearly visible on the

outside of the casing.

Offer the back box up to the wall and check that the rear tamper switch operates.

Should the microswitch not operate, remove the unit from the wall and carefully adjust

the microswitch arm. Once the microswitch operates correctly the unit can be fixed to

the wall and all external wiring connections made.

The diagram PO3045 shows the wiring connections required for the remote receiver.

Only those cables needed to make the remote receiver function should be routed into

the case. The Remote Receiver must NOT be used as a junction box or cable termination

point as this will adversely affect the performance of the system.

When all connections have been made to the remote receiver the battery can be

connected, the lid can be re-fixed and mains voltage can then be applied.

EMS 5000 FIREPOINT

6.2 VHF Remote Receiver

The VHF remote receiver 53-5414 should be wired as shown in the supplied drawing

P03077. The following paragraphs outline the installation in a step by step format.

Remove the four lid retaining screws situated on the front cover. The front section of the

unit can now be removed.

Four fixing holes are available for the unit’s installation. These are clearly on the outside

of the casing.

Offer the back box up to the wall and check that the rear tamper switch operates.

Should the microswitch not operate, remove the unit from the wall and carefully adjust

the microswitch arm. Once the microswitch operates correctly the unit can be fixed to

the wall and all external wiring connections made.

The diagram P03077 shows the wiring connections required for the remote receiver.

Only those cables needed to make the remote receiver function should be routed into

the case. The Remote Receiver must NOT be used as a junction box or cable termination

point as this will adversely affect the performance of the system.

When all connections have been made to the remote receiver the battery can be

connected, the lid can be re-fixed and mains voltage can then be applied.

EMS 5000 FIREPOINT

7. Software Configuration

To allow the Control Panel and remote receivers to work together, some software

configuration will be necessary, the following instructions detail in a step by step format

how the configuration should take place for reliable communication. The menu structure

indicated at the end of this section locates the menus, which require entering.

1With the key the “ON” position, the screen will now display:

2 Press the “0” key. The screen will now display:

3 Press the “YES” key. The screen will now display:

4Press the “YES” key. The screen will now display:

5Enter your PIN number (Engineering default = 221100) and

press the “YES” key. The screen will now display:

6 Press any key and the screen will display:

7Press the “” key, until ‘the screen displays:

8Press the “YES” button and the screen will display.

9 Press the “” key, until ‘the screen displays:

10 Press the “YES” key and the screen will display:

Panel In Access

DATE TIME

| *** Options **** |

> Passwords <

| Time and Date |

YES = Select TIME

| * PIN’s and Access * |

>User Log On <

| View Users |

YES = Select TIME

Enter your PIN

For Access >

Then Press YES TIME

**************************

* Welcome Engineer *

**************************

Push any Key TIME

| *** Options **** |

>Passwords <

| Time and Date |

YES = Select TIME

| Logging |

>Fire System Opts <

| Remote Access |

Yes = select Time

| ** Fire system ** |

>Dev. Disable/Test <

| Net. Disable/Test |

Yes= Select Time

| System Mode |

> Engineers Config <

| Printer Options |

Yes= Select Time

| ** Eng. Config ** |

>Device Database <

| Sounder Options |

Yes= Select Time

EMS 5000 FIREPOINT

11 Press the “” key, until ‘the screen displays:

12 Press the “YES” key followed by the “0” key on the keypad

the screen will now display:

13 Press the “” key, until ‘the screen displays:

14 Press the “YES” button and the screen will display:

15 Press the “” key, until ‘the screen displays:

16 Press the “YES” button and the screen will display:

17 Press the “” key, until ‘the screen displays:

18 Press the “YES” button and the screen will display:

19 Press the “1” key followed by the “YES” key and the screen

will display:

20 Press the “NO” key once and the screen will display:

21 Press the “” key until the screen displays:

| ** Master Setup** |

>Polling Baudrate <

| Auto Re-online |

YES = Select TIME

| Reset Security |

>Reset System <

| Lan Options |

Yes= Select Time

| ** Main Menu ** |

>Pins & Access <

| System Support |

Yes= Select Time

| System Support |

> Serial Comms <

| Pager Setup |

Yes= Select Time

| ** Serial Comms ** |

>Device Table <

| Re-start Bus |

YES = Select TIME

| Re-online Device |

> Bus Master Setup <

| Bus Remote Setup |

Yes= Select Time

| Auto Re-online |

> Port to use <

| ^^^^^^^^^^^^^ |

Yes= Select Time

Master Port = 0

0 = Off, 1 = RS485

2 = PAGER 232 > _

YES = Finish TIME

| Auto Re-online |

> Port to use <

| ^^^^^^^^^^^^^ |

Yes= Select Time

| Re-online Device |

> Bus Master Setup <

| Bus Remote Setup |

Yes= Select Time

| Device Table |

>Re-start Bus <

| Re-Online Device |

YES = Select TIME

EMS 5000 FIREPOINT

22 Press the “YES” button and the screen will display:

23 Once completed the screen will display:

24 Push any key and the screen will display:

25 Press the “”key, until ‘the screen displays:

26 Push any key and the screen will display:

The above display can be used to check how many remote receivers are communicating

with the Control Panel. For each remote receiver that is connected, the MAS number

shown will increase by 10. I.e. if one is connected the MAS will show MAS010 if two

receivers are connected the MAS will show MAS020.

27 Press the “No” key twice. The screen will change to display:

28 Press the “” key, until ‘the screen displays:

29 Press the “YES” button and the screen will display:

30 Press the “” key, until ‘the screen displays:

31 Press the “YES” button and the screen will display:

32 The collector should be set to “ENABLED”, press the “YES”

key to change its status. Once set to “Enabled” press the

“NO” key. The screen will display:

Re-initialising Bus

Please wait….*Done*

Push any key TIME

| Device Table |

>Re-start Bus <

| Re-Online Device |

YES = Select TIME

| Printer Redirect |

>Monitor Comms <

| Delete Device |

YES = Select TIME

HEAP00 AUX=00 PGR=00

REM000 MAS010 T00-00

I00 L00 R00 S00 C00

Push any Key TIME

| System Support |

> Serial Comms <

| Pager Setup |

Yes= Select Time

| Logging |

>Remote Rxers <

| Ext. Comms |

Yes= Select Time

|* Remote Receivers *|

>Receivers Found <

| Enable Receiver |

Yes= Select Time

| Enable Receiver |

>Enable Collector <

| Monitor Traffic |

Yes= Select Time

Collector: ENABLED

Push Yes to change

Push No to escape

Yes= Select Time

| Enable Receiver |

>Enable Collector <

| Monitor Traffic |

Yes= Select Time

Re-initialising Bus

Please wait….* *

Push any key TIME

EMS 5000 FIREPOINT

33 Press the “NO” key once and the screen will display:

34 Press the “” key, until ‘the screen displays:

35 Press the “YES” button and the screen will display:

36 Press the “YES” button and the screen will display:

37 Enter “00” followed by the “YES” key. The screen

will display:

38 Push any key and the screen will display:

39 Press the “” key, until ‘the screen displays:

40 Press the “YES” button and the screen will display:

41 The router should be set to “ENABLED”, press the “YES”

key to change its status. Once set to “Enabled” press the

“NO” key. The screen will display:

42 Press the “NO” key twice and the screen will display:

43 Now turn the control keyswitch to the “OFF” position and

the screen will display: The Remote Receiver is now

programmed to the System.

| Logging |

>Remote Rxers <

| Ext. Comms |

Yes= Select Time

| Checksum Data |

> Network Router <

| Radio Lan |

Yes= Select Time

| * NETWORK ROUTER *|

>Setup local NUA <

| View network NUA |

Yes= Select Time

Local NUA :

Input Local NUA_

Yes= Finish Time

| * NETWORK ROUTER*|

> Setup local NUA <

| View network NUA |

Yes= Select Time

_ _SET AS MASTER _ _

Push Any Key Time

| Network Name |

> Control Routing <

| Send Test |

Yes= Select Time

Routing : DISABLED

Push YES to change

Push NO to escape

Yes/No Time

| Network Name |

> Control Routing <

| Send Test |

Yes= Select Time

Panel In Access

Date Time

Status Normal

Date Time

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere EMS Empfänger Handbücher

EMS

EMS 7000 Iris+ Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung