Enable-IT 864P Mini DSLAM Bedienungsanleitung

Enable-IT 864P

Mini DSLAM

PoE Ethernet Extender Kit

User Manual

INTRODUCING THE 864P MINI DSLAM POEETHERNET

Congratulations on purchasing Enable-IT’s 864P Mini Extended Ethernet PoE DSLAM

— the simplest method to stretch your broadband solutions for in-building deployment in

commercial office buildings, hotels, and multi-tenant residential units.

The 864P Mini PoE DSLAM product offers the lowest cost solution in a simple design for

rapid install using existing 1-pair Telco wiring.

This chapter contains introductory information about the 864P Mini Extended Ethernet

PoE DSLAM and how it can be used in your network. It covers the following topics:

•About the 864P Mini Extended Ethernet PoE DSLAM

•Key Benefits

•Summary of Features

•Typical Applications

About The 864P Mini Extended Ethernet PoE DSLAM

The 864P Mini PoE DSLAM solution addresses the problem of high costs associated

with stretching your backbone with traditional fiber or a series of hubs/repeaters.

In many office buildings, preferred network access is a dedicated Ethernet line,

however, Ethernet over twisted pair wiring has a distance limitation of 328ft. In order

to drive Ethernet signal further, one would have to add repeaters to each segment of

328ft twisted pair cabling; this is often insufficient and too costly in multi-story

buildings. Fortunately, the Enable-IT 864P Mini PoE DSLAM Series extended

Ethernet solutions can push the reach of Ethernet to more than (19) nineteen times

the typical Ethernet distance over a 1-pair Telco wiring infrastructure or better.

A simple design methodology would be to think of the 864P Mini PoE DSLAM extending

a standard Ethernet line up to 6,000ft (1,829m) with a 4-Port 10/100 Ethernet switch,

and can also include dual voice lines simultaneously.

To increase the durability and extended use of the product providing maximum future

technology protection, the 864P Mini Extended Ethernet PoE DSLAM meets the

challenge of modern switched LANs, and allows you to add features and capacity as

your network expands. The Enable-IT 864P Mini PoE DSLAM extended Ethernet

solution has been tested to provide Full-Duplex transport up to 90Mbps over CAT2, and

up to 100Mbps over CAT5e cabling.

Up to 700ft (213m) - 100Mbps

700ft (213m) to 1,350ft (411m) - 90Mbps

1,350ft (411m) to 1,970ft (600m) - 70Mbps

1,970ft (600m) to 2,625ft (800m) - 52Mbps

2,625ft (800m) to 3,280ft (1000m) - 42Mbps

3,300ft (1006m) to 6,000(1,829m) - 30Mbps

Unit Model

Wiring

LAN Data Rate

Max. Distance

860 Pro 1-pair CAT2, up to CAT7 100Mbps FD 6,000ft (1,829m)

* Actual data rate will vary on the

quality of the copper in the wire,

twisted vs. straight pair and

environmental electromagnetic

interference factors.

Key Benefits

The following list identifies the 864P Mini Extended Ethernet PoE DSLAM key benefits.

•Dramatic cost reduction over any competing technology and includes a 4-Port

10/100 LAN switch on each end. Rapid installation with small box profile, no

programming and no firmware to upgrade

•Broadband technology that delivers in-building Ethernet access over 1-pair of

existing Category 2, up to Category 5e, 6 or 7, wiring at a maximum distance of

6,000ft (1,829m). Existing spare or actively in use for analog wiring can be used

as well. This means no new wiring is required.

•Provides one scalable infrastructure for Internet access, POTS, VoIP, video, and

virtual private networking (VPN).

•Low profile box capable of supporting Ethernet data all in a single RJ-45 Ethernet

jack (Interlink port).At time of ordering, or afterwards, a RJ-45 dongle can be

requested to use on RJ-11 telephone wiring.

•861P PoE CPE - Quad switched RJ-45 10/100 LAN Ethernet ports for expansion

without adding a hub or switch on each end.

Summary Of Features

The Enable-IT 864P Mini Extended Ethernet PoE DSLAM has the following hardware

features:

•Extended Ethernet line over existing CAT2 up to CAT5e / CAT7 wiring

•Uses RJ-45 Interlink port for transport (dual voice, 100Mbps data and PoE)

•Rapid Telco style installation – no programming required

•Supports digital VoD channels and maintains existing telephone (lifeline POTS)

•Drives Ethernet 100Mbps Full-Duplex service delivery with quad LAN switch,

dual voice up to 6,000ft (1,829m) - can also transport PoE up to 2,500ft natively.

•Network equipment independence – transparent to protocols/applications/MAC

Specifications: Functionality:

Power Indicator Data Rates 10/100Mbps Full-Duplex

100Mbps Link Status/Activity Full-Duplex/Half-Duplex Status/Collisions

VDSL2 Link Status/Activity Protocol independent

Physical Dimensions: 864P Mini PoE DSLAM Interlink ports:

Height: 1.5" (38.1mm) Pins 1 & 2 – Voice line 1 and Ethernet data

Depth: 3.5" (88.9mm) Pins 3 & 6 – Voice line 2 (optional)

Width: 4.26” (108.2mm) Pins 4 & 5 – optional support for PoE

Weight: .4lbs (6.4oz) 2.5lbs Pins 7 & 8 – optional support for PoE

Environment: Interfaces:

Operating temp: -49°F to 168°F (-45°C to 76°C) (1) 5v 4A DC Power Adapter 2.1mm

Storage temp: -49°F to 168°F (-45°C to 76°C) (2) RJ-45 100Mbps LAN Auto negotiate

Humidity 5% to 95%, non-condensing (4) RJ-45 Interlink port

Typical Use Applications

The Enable-IT, Inc. 864P Mini Extended Ethernet PoE DSLAM are usually installed into

telephone wiring infrastructures where extension of backbone services is required and

expensive fiber options are prohibitive. The 864P Mini Extended Ethernet PoE DSLAM

allows a standard Ethernet segment to be deployed quickly over existing 1-pair Telco

copper wiring in combination with existing POTS voice signals. The 864P Mini PoE

DSLAM Interlink ports (RJ-45 interface) carries this 1-pair signaling over the RJ-45 pins

1 & 2 - used as transport for both voice and data. If you use more than 1-pair of wiring,

such as a CAT5 segment, the RJ-45 (pins 3 & 4) are used for voice line 2, and the

remaining pins (4,5,7 & 8) can transport native 802.3af PoE, or are unused.Quad

switched RJ-45 10/100 auto-sensing ports allow the use of LAN devices without adding

an Ethernet hub or switch to either end. An optional RJ-45 dongle can be used in unison

with the RJ-45 Interlink wiring as DSL filters to clean up noise bleeding over your

cabling, as well as combined use for RJ-11 Telephone connections.

Installers have the convenience of a 100Mbps LAN Ethernet unit for peace of mind

connectivity and no device maintenance. Rapid installation allows for minimal

interruption, and the Broadband technology allows for investment protection up to 10 -15

years with no firmware or replacement issues. Bandwidth can be scaled according to

the Broadband access provider needs. The 864P Mini PoE DSLAM is a passive device

so interruption of Internet service does not affect POTS services. Carriers and access

providers can come and go, but the 864P Mini PoE DSLAM extended Ethernet

technologies continue to provide lasting value, such as other utilities like water, gas and

electricity.

The Enable-IT 864P Mini Extended Ethernet PoE DSLAM is suited for the following key

environments:

•Commercial Buildings (Multi-Tenant Units)

•Business Parks (Multi-Tenant Units)

•Apartments (Multi-Residential Units)

•Hotels (Multi-Hospitality Units)

•Business Suites (Multi-Hospitality Units)

•School Campuses (University, K-12)

•College Housing (Multi-Residential Units)

•Mining Operations – Quarries, Mine Shafts

•Nautical Infrastructure – Cruise Ships, Marinas, Dive Operations, Submarines

•Video Surveillance/Security

•WiFi Deployment – ISP’s, RV Parks, Construction Sites

•Manufacturing – Foundries, Pharmaceutical, Aerospace, Automotive,

Petroleum, Concrete Plants, etc.

•Retail POS – Department stores, Bars, restaurants, retail spaces

•Government – Naval ships, FEMA, Housing, USGS, National Parks, Forestry,

Research Stations, NASA, Utilities, etc.

•Education – Outdoor Camps, College & University Campuses

•Healthcare – Hospitals, Elder Care, Outpatient Facilities

•Entertainment – Movie theaters, Home Entertainment, Fairs, Outdoor Venues

INSTALLING THE 864P MINI POEDSLAM

The Enable-IT 864P Mini PoE DSLAM has a distance restriction of 6,000ft (1,829m) over

1-pair of Category 2, up to 4-pair CAT5e / CAT7, wiring from device extension to device

extension. Therefore quick, simple site surveys and installation planning are highly

recommended.

This chapter describes the recommended installation process for the Enable-IT 864P

Mini Extended Ethernet PoE DSLAM. The following topics are covered:

•Site Plan – Installation Design Considerations

•Unpacking the Enable-IT 864P Mini Extended Ethernet PoE DSLAM

•Perform an Out Of The Box Test (OOTBT)

•Performing the On-Site Installation

Site Plan – Installation Design Considerations

The planning process should involve a site walk-through and discovery survey.

Electrical cable measurement tools are the most reliable method to determine the

longest run of hidden wiring. Estimate the best locations to position the Broadband

concentrators to adequately reach desired connectivity on each floor. Document your

findings to use in designing a network topology to support the Ethernet switches and

backbone connectivity. The following are key points to remember in the site survey:

•Total distance limitation of 6,000ft (1,829m) from end-to-end.

•1-Pair CAT2 wiring, or 4-pair CAT5e, .30 gauge, or better, cabling is required for

the 864P Mini PoE DSLAM Interlink ports transmission.

For the Interlink wiring you will need to use RJ-45 connectors. Crimp a RJ-45 Male head

to each end of the contiguous wire run and use pins 1 & 2 straight through. This will

deliver 1 voice line, and Ethernet data. If you desire to use the second voice line, you

can also use pins 3 & 6 on each end straight through.

The 864P Mini PoE DSLAM Interlink ports (RJ-45) carries this 1-pair signaling over the

RJ-45 pins (1 & 2) - used as transport for both voice and data. If you use more than 1-

pair of wiring, such as a CAT5 segment, the RJ-45 pins 3 & 4 are used for voice line 2,

and the remaining pins (4,5,7 & 8) can transport native 802.3af PoE, or are unused. As

an option, telephone dongles can be provided for use with existing RJ-11 wiring.

864P Mini PoE DSLAM

861P PoE CPE

Unpacking the Enable-IT 864P Mini Extended Ethernet PoE DSLAM

Carefully remove the Enable-IT 864P Mini PoE DSLAM packing materials from the box.

Verify that the items listed below are present. Make sure that the equipment supplied

matches what you ordered. If any items are missing or damaged, please contact

Enable-IT or your distributor for assistance.

•(1) Enable-IT 864P Mini PoE DSLAM

o5v AC/DC Country Specific Power adapter

o10ft Ethernet LAN patch cables, Black

o(2) Enable-IT 360 PoE Injectors

•(1) Enable-IT 864P Mini Extended Ethernet PoE DSLAM Quickstart Guide

Perform an Out of the Box Test (OOTBT)

We highly recommend a quick test to ensure the working order of you 864P PoE

DSLAM. First power on the 864P with the supplied power cord. Next, take the 360

PoE Injector provided and power on the unit. Then connect the injector to LAN 1

on the 864P. Use one of the Ethernet patch cords provided and attach to the 864P

Interlink port to each 861P PoE CPE unit. Your 861P CPE units should now be

powered on. The Green Sync LEDs will start flickering slowly and then fast as the

units talk to each other. After a few seconds you should see a solid Green

Interlink Sync LED on each unit to confirm a link is established. This confirms

basic proper operation of the units. Next for a more detailed test and to confirm

your LAN Equipment works with the 864P, connect your Ethernet LAN to the 864P

LAN ports and your Ethernet LAN at the remote CPE end and test connectivity.

The Green Interlink Sync LED will pulse rapidly as it detects traffic.

LED indicators will provide visual operational status of the 864P Mini PoE DSLAM and

861P PoE CPE.

Mode –Yellow Solid LED

Off = CO unit

On = CPE unit

Sync – Green slow to fast flicker LED on power up – indicates negotiation of a link

–Green solid LED indicates link established and rapid pulse is traffic

Act – Yellow LED

Off = No device attached or detected

On = Solid, indicates the presence of local LAN

On = Blinking, indicates the presence of local LAN traffic

Pwr – Green Solid LED indicates the unit is receiving 5v power

Performing the On-Site Installation

After removing the Enable-IT 864P Mini Extended Ethernet PoE DSLAM from the box,

and performing the Out Of The Box Testing (OOTBT), all that remains to install the unit

on-site is to mount the unit, build the interconnect wiring, add voice lines if needed, and

attach the LAN device cabling with the provided Ethernet Patch cords.

Mounting the Enable-IT 861P PoE CPE Ethernet Extender Units

The Enable-IT 861P PoE Ethernet Extender CPE are designed for quick wall mounting.

Choose a location to mount each of the Enable-IT 861P PoE CPE where the maximum

distance does not exceed 6,000ft (1,829m) total between devices to be connected.

When wall-mounting the Enable-IT 864P Mini PoE DSLAM unit it is recommended that

you use the appropriate screw anchors for your mounting surface. If mounting on

existing plywood use wood screws; if mounting onto drywall or sheetrock, use plastic

drywall anchors to secure your installation.

Building the 864P Mini PoE DSLAM Interlink Wiring

The most important aspect of the installation is the correct wiring of the Interlink cabling.

The 864P Mini PoE DSLAM Interlink port (RJ-45 interface) carries this 1-pair signaling

over the RJ-45 (pins 1 & 2) - used as transport for both voice and data. If you use more

than 1-pair of wiring, such as a CAT5 segment, the RJ-45 (pins 3 & 4) are used for voice

line 2, and the remaining pins (4,5,7 & 8) can transport native 802.3af PoE, or are

unused.

For all wiring you will need to crimp a RJ-45 Male head to each end of the contiguous

wire run and using the following (pins 1 & 2) straight through. This will deliver 1 voice

line, and Ethernet data. If you desire to use the second voice line, you will need to

request our optional dongle that will allow for connecting telephone lines to this interlink

wiring. Insert the completed RJ-45 ends into the 864P Mini PoE DSLAM Interlink port on

each 861P PoE CPE unit.

864P Mini PoE DSLAM

861P CPE

Cabling Devices To The Enable-IT 864P Mini PoE DSLAM Extended Ethernet Kit

Attach your remote LAN device to the 864P Mini PoE DSLAMCPE unit LAN ports with

Ethernet patch cord provided. Attach your local LAN to the 864P Mini PoE DSLAMCO

LAN ports with Ethernet patch cord provided. Attach the power adapters to both 864P

Mini PoE DSLAM units.

Attachyour local Interlink cabling end to the 864P Mini PoE DSLAM Interlink ports –

Then do the same for the remote end and plug into the 864P Mini PoE DSLAMCPE unit

Interlink port. The Sync LED’s will flicker in a sequence, talking to each other until they

go solid. Your equipment should now be powered up and functioning.

LED indicators will provide visual operational status of the 864P Mini PoE DSLAM and

861P PoE CPE.

Mode –Yellow Solid LED

Off = CO unit

On = CPE unit

Sync – Green slow to fast flicker LED on power up – indicates negotiation of a link

–Green solid LED indicates link established and rapid pulse is traffic

Act – Yellow LED

Off = No device attached or detected

On = Solid, indicates the presence of local LAN

On = Blinking, indicates the presence of local LAN traffic

Pwr – Green Solid LED indicates the unit is receiving 5v power

Troubleshooting

First examine the backbone wiring pair and make sure you have solid connections. The

Interlink Sync LED will be lit solid Green with rapid pulsing on each 864P Mini PoE DSLAM to

show proper connection and pairing. If the Interlink Sync LED Link is flashing slow to fast

and never goes solid…. Then follow the steps below:

1) Make sure your wiring is straight through and not connected to any Telco punch

down blocks; If so remove from the block and use Telco butt clips to bridge

wire.

2) Check for a firm connection of the RJ-45 connections in each 864P Mini PoE

DSLAM unit, and power is applied to the 864P Mini PoE DSLAM & 861P PoE

CPE units.

3) You can easily isolate any issue by performing an Out of the Box Test

(OOTBT).This test will confirm the correct working order of your Enable-IT

864P Mini Extended Ethernet PoE DSLAM. This will point to a possible issue

with your long distance Interlink wiring being affected by possible outside

interference.

Performance Settings (DIP Switch)

If you are experiencing performance issues with your Ethernet connection you may use the

following DIP switch settings to adjust your application. For DIP switch 2-4 you must toggle

both symmetrically, in other words the 864P and 861P PoE CPE must match. If you turn DIP

switch 3 Up (Off) on the CO, then you must do so for the CPE and vice-versa.

•Switch 1: CO / CPE Mode

CO Mode – Up / Off Position

CPE Mode – Down / On Position

Central Office Equipment (CO) is generally the equipment residing at the Carrier

Telephone office or the head end of a circuit. Customer Premise Equipment (CPE) is

generally the equipment residing on the customer side of a circuit. Typically you would

place the CO at the local end and the CPE at the remote end for reference only. CO’s

only communicate with CPE’s.

•Switch 2: Interleaved / Fast Channel

Interleaved Channel – Up / Off Position

Fast Channel – Down / On Position (Default)

Interleaved channel works better for file transfers, where the delivered data must be error

free but latency incurred by the retransmission of error packets is acceptable. Fast

channel is preferred for streaming multimedia, where an occasional dropped bit is

acceptable, but lags are less so.

•Switch 3: Asymmetrical / Symmetrical Mode

Asymmetrical Mode – Up / Off Position

Symmetrical Mode – Down / On Position (Default)

Asymmetrical mode weighs in favor of download speed while sacrificing upload speed

bandwidth. Symmetrical will balance out the download/upload speed for transmitting data

packets. We suggest flipping DIP switch 3 Up (OFF) at a distance of 1,500 feet or less.

•Switch 4: Signal-to-noise Noise Ratio (SNR)

9dB – Up / Off Position

6dB – Down / On Position (Default)

Signal-to-noise ratio is a measurement that refers to how much noise is in the output of a

device, in relation to the signal level. If you experience issues of noise bleeding over the

lines, or high interference in your environment, it is suggested that you switch to 6dB SNR

and change to Interleaved channel.This may help clean up any noise bleeding over your

cabling.

Dieses Handbuch passt für folgende Modelle

Andere Enable-IT Extender Handbücher

Enable-IT

Enable-IT 860XC PRO Bedienungsanleitung

Enable-IT

Enable-IT 821C Bedienungsanleitung

Enable-IT

Enable-IT 865 PRO Bedienungsanleitung

Enable-IT

Enable-IT 860 Series Bedienungsanleitung

Enable-IT

Enable-IT 828 Bedienungsanleitung

Enable-IT

Enable-IT 860 Pro Rev B Bedienungsanleitung

Enable-IT

Enable-IT 860XS PRO Bedienungsanleitung

Enable-IT

Enable-IT 865W PRO Bedienungsanleitung

Enable-IT

Enable-IT 865 PTZ PRO Bedienungsanleitung

Enable-IT

Enable-IT 865XW PRO Bedienungsanleitung

Enable-IT

Enable-IT 865XC PRO Bedienungsanleitung

Enable-IT

Enable-IT 865XSC PRO Bedienungsanleitung

Enable-IT

Enable-IT 865 Q PRO Bedienungsanleitung

Enable-IT

Enable-IT 821CP Bedienungsanleitung

Enable-IT

Enable-IT 865X PRO Bedienungsanleitung

Enable-IT

Enable-IT 860 W PRO Bedienungsanleitung

Enable-IT

Enable-IT 868 Bedienungsanleitung

Enable-IT

Enable-IT 821P Bedienungsanleitung

Enable-IT

Enable-IT 865W PRO Bedienungsanleitung

Enable-IT

Enable-IT 868 PRO Bedienungsanleitung

Enable-IT

Enable-IT 850 CPE Bedienungsanleitung

Enable-IT

Enable-IT 864 Bedienungsanleitung

Enable-IT

Enable-IT 895 Series Bedienungsanleitung

Enable-IT

Enable-IT 865 PTZQ PRO Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung