Endress+Hauser Liquiphant FTL62 Technische Daten
Products Solutions Services
Brief Operating Instructions
Liquiphant FTL62
Vibronic
HART
Point level switch with highly corrosion-resistant
coating for liquids
These Brief Operating Instructions are not a substitute for the
Operating Instructions pertaining to the device.
Detailed information is provided in the Operating Instructions
and other documentation.
Available for all device versions via:
• Internet: www.endress.com/deviceviewer
• Smartphone/tablet: Endress+Hauser Operations app
KA01558F/00/EN/02.23-00
71630440
2023-11-30
Related documents Liquiphant FTL62 HART
2 Endress+Hauser
1 Related documents
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555
Liquiphant FTL62 HART About this document
Endress+Hauser 3
2 About this document
2.1 Symbols
2.1.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
2.1.2 Electrical symbols
Ground connection
Grounded clamp, which is grounded via a grounding system.
Protective earth (PE)
Ground terminals, which must be grounded prior to establishing any other connections. The
ground terminals are located on the inside and outside of the device.
2.1.3 Tool symbols
Flat-blade screwdriver
Allen key
Open-ended wrench
2.1.4 Communication-specific symbols
Bluetooth
Wireless data transmission between devices over a short distance.
2.1.5 Symbols for certain types of information
Permitted
Procedures, processes or actions that are permitted.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information
Basic safety instructions Liquiphant FTL62 HART
4 Endress+Hauser
Reference to documentation
A
Reference to another section
1.
,
2.
,
3.
Series of steps
2.1.6 Symbols in graphics
A, B, C ... View
1, 2, 3 ... Item numbers
-
Hazardous area
.
Safe area (non-hazardous area)
2.1.7 Registered trademarks
HART®
Registered trademark of the FieldComm Group, Austin, Texas, USA
Bluetooth®
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG,
Inc. and any use of such marks by Endress+Hauser is under license. Other trademarks and
trade names are those of their respective owners.
Apple®
Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the
U.S. and other countries. App Store is a service mark of Apple Inc.
Android®
Android, Google Play and the Google Play logo are trademarks of Google Inc.
3 Basic safety instructions
3.1 Requirements for the personnel
The personnel must fulfill the following requirements to carry out the necessary tasks, e. g.,
commissioning and maintenance:
‣Trained, qualified specialists must have a relevant qualification for the specific function
and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Must have read and understood the instructions in the manual and supplementary
documentation
‣Follow instructions and comply with conditions
3.2 Intended use
• Only use the device for liquids
• Improper use can pose hazards
• Ensure that the measuring device is free of defects while it is in operation
Liquiphant FTL62 HART Basic safety instructions
Endress+Hauser 5
• Use the device only for media to which the wetted materials have an adequate level of
resistance
• Do not exceed or drop below the relevant limit values for the device
For more details, see the Technical Documentation
3.2.1 Incorrect use
The manufacturer is not liable for damage caused by improper or non-intended use.
Residual risks
Due to heat transfer from the process, the temperature of the electronics housing and the
assemblies contained therein may rise to 80 °C (176 °F) during operation.
Danger of burns from contact with surfaces!
‣If necessary, ensure protection against contact to prevent burns.
For requirements concerning functional safety in accordance with IEC 61508, the associated
SIL documentation must be observed.
3.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
3.4 Operational safety
Risk of injury!
‣Operate the device only if it is in proper technical condition, free from errors and faults.
‣The operator is responsible for ensuring the interference-free operation of the device.
Modifications to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability:
‣Only perform repair work on the device if this is expressly permitted.
‣Observe federal/national regulations pertaining to the repair of an electrical device.
‣Use original spare parts and accessories from Endress+Hauser only.
Hazardous area
To eliminate danger to persons or the facility when the device is used in the hazardous area
(e.g. explosion protection):
‣Check the nameplate to verify whether the ordered device can be used for the intended
purpose in the hazardous area.
‣Observe the specifications in the separate supplementary documentation that is an integral
part of this manual.
Incoming acceptance and product identification Liquiphant FTL62 HART
6 Endress+Hauser
3.5 Product safety
This device is designed in accordance with good engineering practice to meet state-of-the-art
safety requirements, has been tested, and left the factory in a condition in which it is safe to
operate.
It meets the general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms
this by affixing the CE mark to the device.
3.6 Functional Safety SIL (optional)
The Functional Safety Manual must be strictly observed for devices that are used in functional
safety applications.
3.7 IT security
For more information, see the Operating Instructions.
4 Incoming acceptance and product identification
4.1 Incoming acceptance
Check the following during incoming acceptance:
Are the order codes on the delivery note and the product sticker identical?
Are the goods undamaged?
Do the data on the nameplate match the ordering information on the delivery note?
If required (see nameplate): are the Safety Instructions e.g. XA provided?
If one of these conditions is not met, please contact the manufacturer's sales office.
4.2 Product identification
The device can be identified in the following ways:
• Nameplate specifications
• Extended order code with breakdown of the device features on the delivery note
• Enter serial number from nameplates in W@M Device Viewer
www.endress.com/deviceviewer. All of the information on the measuring device is
displayed along with an overview of the scope of technical documentation provided.
• Enter the serial number on the nameplate into the Endress+Hauser Operations app or scan
the 2-D matrix code on the nameplate with the Endress+Hauser Operations app
4.2.1 Electronic insert
Identify the electronic insert via the order code on the nameplate.
Liquiphant FTL62 HART Mounting
Endress+Hauser 7
4.2.2 Nameplate
The information that is required by law and is relevant to the device is shown on the
nameplate.
4.2.3 Manufacturer address
Endress+Hauser SE+Co. KG
Hauptstraße 1
79689 Maulburg, Germany
Place of manufacture: See nameplate.
4.3 Storage and transport
4.3.1 Storage conditions
Use original packaging.
Storage temperature
–40 to +80 °C (–40 to +176 °F)
Optional –50 °C (–58 °F) or –60 °C (–76 °F)
4.3.2 Transporting the device
NOTICE
Flange, pipe extension and tuning fork are either plastic-coated or enamel-coated.
Scratches or impacts may cause damage to the coated surface of the device.
‣Hold the device only by the housing, flange or extension pipe, protect coated surface
appropriately.
‣Transport the device to the measuring point in the original packaging.
‣Do not bend, shorten or extend the tuning fork.
5 Mounting
Mounting instructions
• Any orientation for device with a pipe length of up to 500 mm (19.7 in)approx.
• Vertical orientation from above for device with long pipe
• Minimum distance between the tuning fork and the tank wall or pipe wall: 10 mm (0.39 in)
Mounting Liquiphant FTL62 HART
8 Endress+Hauser
A0042153
1 Installation examples for a vessel, tank or pipe
5.1 Mounting requirements
NOTICE
Scratches or impacts damage the coated surface of the device.
‣Ensure the device is handled properly and professionally during all mounting work.
In the case of sensors with an ECTFE or PFA coating, a PTFE seal is fixed on the flange.
5.1.1 Pay attention to the temperature for devices with a PFA coating (conductive)
The difference in temperature between the outer and inner side of the flange may not exceed
60 °C (140 °F).
If necessary, use external insulation.
Liquiphant FTL62 HART Mounting
Endress+Hauser 9
A
B
BA
-
C
1C
=
A0042298
2 Difference in temperature between outer and inner side of flange
1 Insulation
A Temperature of flange, outer side
B Temperature of flange, inner side, for ECTFE maximum 120 °C (248 °F)
C Temperature difference for ECTFE, PFA maximum 60 °C (140 °F)
5.1.2 Take switch point into consideration
The following are typical switch points, depending on the orientation of the point level switch
and coating.
Water +23 °C (+73 °F)
Minimum distance between the tuning fork and the tank wall or pipe wall:
10 mm (0.39 in)
Plastic-coated tuning fork (ECTFE, PFA)
~13 (0.5)
D
A
~12.5 (0.49)
C
D
~6 (0.24)
B
D
A0042269
3 Typical switch points, plastic-coated tuning fork (ECTFE, PFA). Unit of measurement mm (in)
A Installation from above
B Installation from below
C Installation from the side
D Switch point
Mounting Liquiphant FTL62 HART
10 Endress+Hauser
Enamel-coated tuning fork
~17 (0.67)
D
A
~14 (0.55)
C
D
D
~5 (0.2)
B
A0043327
4 Typical switch points, enamel-coated tuning fork. Unit of measurement mm (in)
A Installation from above
B Installation from below
C Installation from the side
D Switch point
5.1.3 Take viscosity into consideration
Viscosity values
• Low viscosity : < 2 000 mPa⋅s
• High viscosity: > 2 000 to 10 000 mPa⋅s
Low viscosity
Low viscosity, e.g. water: < 2 000 mPa⋅s
It is permitted to position the tuning fork within the installation socket.
> 25 (0.98)
> !50 (1.97)
A0042204
5 Installation example for low-viscosity liquids. Unit of measurement mm (in)
Andere Handbücher für Liquiphant FTL62
5
Andere Endress+Hauser Messgerät Handbücher
Endress+Hauser
Endress+Hauser Prosonic S FMU90 PROFIBUS DP Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proline Promag W 300 PROFINET Bedienungsanleitung
Endress+Hauser
Endress+Hauser FQG66 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proline Promass 83 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Micropilot S FMR530 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Micropilot S FMR540 Bedienungsanleitung
Endress+Hauser
Endress+Hauser RMM621 Technische Daten
Endress+Hauser
Endress+Hauser Micropilot FMR67B Bedienungsanleitung
Endress+Hauser
Endress+Hauser Liquipoint T FTW31 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proline Promag 55 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proline Promass 84 MODBUS RS485 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Levelflex M FMP43 Bedienungsanleitung
Endress+Hauser
Endress+Hauser RIA46 Technische Daten
Endress+Hauser
Endress+Hauser Levelflex FMP51 Firmware-Update
Endress+Hauser
Endress+Hauser LT1100 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proserve NMS80 Gebrauchsanweisung
Endress+Hauser
Endress+Hauser Levelflex FMP56 Bedienungsanleitung
Endress+Hauser
Endress+Hauser magphant Bedienungsanleitung
Endress+Hauser
Endress+Hauser Proline Promag 50 Bedienungsanleitung
Endress+Hauser
Endress+Hauser Prosonic T FMU30 Technische Daten
