Endress+Hauser Liquiphant FTL64 Technische Daten

Products Solutions Services

Brief Operating Instructions

Liquiphant FTL64

Vibronic

Point level switch for liquids in high-temperature

applications

These Instructions are Brief Operating Instructions; they are

not a substitute for the Operating Instructions pertaining to

the device.

Detailed information about the device can be found in the

Operating Instructions and the other documentation:

Available for all device versions via:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

KA01480F/00/EN/02.22-00

71566288

2022-04-05

Associated documentation Liquiphant FTL64

2 Endress+Hauser

1 Associated documentation

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

2 About this document

2.1 Symbols

2.1.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

Liquiphant FTL64 About this document

Endress+Hauser 3

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

2.1.2 Electrical symbols

Ground connection

Grounded clamp, which is grounded via a grounding system.

Protective earth (PE)

Ground terminals, which must be grounded prior to establishing any other connections. The

ground terminals are located on the inside and outside of the device.

2.1.3 Tool symbols

Flat-blade screwdriver

Allen key

Open-ended wrench

2.1.4 Symbols for certain types of information

Permitted

Procedures, processes or actions that are permitted.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information

Reference to documentation

Reference to another section

Series of steps

2.1.5 Symbols in graphics

A, B, C ... View

1, 2, 3 ... Item numbers

Hazardous area

Safe area (non-hazardous area)

Basic safety instructions Liquiphant FTL64

4 Endress+Hauser

3 Basic safety instructions

3.1 Requirements for the personnel

The personnel must fulfill the following requirements to carry out the necessary tasks, e. g.,

commissioning and maintenance:

‣Trained, qualified specialists must have a relevant qualification for the specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Must have read and understood the instructions in the manual and supplementary

documentation

‣Follow instructions and comply with conditions

3.2 Intended use

• Only use the device for liquids

• Improper use can pose hazards

• Ensure that the measuring device is free of defects while it is in operation

• Use the device only for media to which the wetted materials have an adequate level of

resistance

• Do not exceed or drop below the relevant limit values for the device

For more details, see the Technical Documentation

3.2.1 Incorrect use

The manufacturer is not liable for damage caused by improper or non-intended use.

Residual risks

Due to heat transfer from the process, the temperature of the electronics housing and the

assemblies contained therein may rise to 80 °C (176 °F) during operation.

Danger of burns from contact with surfaces!

‣If necessary, ensure protection against contact to prevent burns.

For requirements concerning functional safety in accordance with IEC 61508, the associated

SIL documentation must be observed.

3.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

3.4 Operational safety

Risk of injury!

‣Operate the device only if it is in proper technical condition, free from errors and faults.

‣The operator is responsible for ensuring the interference-free operation of the device.

Liquiphant FTL64 Incoming acceptance and product identification

Endress+Hauser 5

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

‣If, despite this, modifications are required, consult with Endress+Hauser.

Repair

To ensure continued operational safety and reliability:

‣Only perform repair work on the device if this is expressly permitted.

‣Observe federal/national regulations pertaining to the repair of an electrical device.

‣Use original spare parts and accessories from Endress+Hauser only.

Hazardous area

To eliminate danger to persons or the facility when the device is used in the hazardous area

(e.g. explosion protection):

‣Check the nameplate to verify whether the ordered device can be used for the intended

purpose in the hazardous area.

‣Observe the specifications in the separate supplementary documentation that is an integral

part of this manual.

3.5 Product safety

This device is designed in accordance with good engineering practice to meet state-of-the-art

safety requirements, has been tested, and left the factory in a condition in which it is safe to

operate.

It meets the general safety standards and legal requirements. It also complies with the EU

directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms

this by affixing the CE mark to the device.

4 Incoming acceptance and product identification

4.1 Incoming acceptance

Check the following during incoming acceptance:

 Are the order codes on the delivery note and the product sticker identical?

 Are the goods undamaged?

 Do the data on the nameplate match the ordering information on the delivery note?

 If required (see nameplate): are the Safety Instructions e.g. XA provided?

If one of these conditions is not met, please contact the manufacturer's sales office.

Mounting Liquiphant FTL64

6 Endress+Hauser

4.2 Product identification

The following options are available for the identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

• Enter serial number from nameplates in W@M Device Viewer

www.endress.com/deviceviewer. All of the information on the measuring device is

displayed along with an overview of the scope of technical documentation provided.

• Enter the serial number on the nameplate into the Endress+Hauser Operations app or scan

the 2-D matrix code on the nameplate with the Endress+Hauser Operations app

4.2.1 Electronic insert

Identify the electronic insert via the order code on the nameplate.

4.2.2 Nameplate

The information that is required by law and is relevant to the device is shown on the

nameplate.

4.3 Storage and transport

4.3.1 Storage conditions

Use original packaging.

Storage temperature

–40 to +80 °C (–40 to +176 °F)

Optional: –50 °C (–58 °F), –60 °C (–76 °F)

Transporting the device

• Transport the device to the measuring point in the original packaging

• Hold the device by the housing, temperature spacer, flange or extension pipe

Take suitable measures to protect the coating!

Do not bend, shorten or extend the tuning fork.

5 Mounting

LWARNING

Loss of protection rating if the device is opened in a wet environment.

‣Only open the device in a dry environment!

Mounting instructions

• Any orientation for device with short pipe up to approx. 500 mm (19.7 in)

• Vertical orientation from above for device with long pipe

• Minimum distance between the fork tip and the tank wall or pipe wall: 10 mm (0.39 in)

Liquiphant FTL64 Mounting

Endress+Hauser 7

A0042329

 1 Installation examples for a vessel, tank or pipe

1 Vessel insulation (example with temperature spacer)

If process temperatures are high, the device should be included in a vessel insulation system to prevent

the electronics from heating as a result of thermal radiation or convection.

5.1 Mounting requirements

NOTICE

Scratches or impacts damage the coated surface of the device.

‣Ensure the device is handled properly and professionally during all mounting work.

5.1.1 Take switch point into consideration

The following are typical switch points, depending on the orientation of the point level switch.

Water +23 °C (+73 °F)

Minimum distance between the fork tip and the tank wall or pipe wall: 10 mm (0.39 in)

Mounting Liquiphant FTL64

8 Endress+Hauser

~13 (0.5)

~5 (0.2)

~12.5 (0.49)

A B C

A0044069

 2 Typical switch points. Unit of measurement mm (in)

A Installation from above

B Installation from below

C Installation from the side

D Switch point

5.1.2 Take viscosity into consideration

Viscosity values

• Low viscosity : < 2 000 mPa⋅s

• High viscosity: > 2 000 to 10 000 mPa⋅s

Low viscosity

It is permitted to position the tuning fork within the installation socket.

> 25 (0.98)

> !50 (1.97)

A0042333

 3 Installation example for low-viscosity liquids. Unit of measurement mm (in)

Liquiphant FTL64 Mounting

Endress+Hauser 9

High viscosity

NOTICE

Highly viscous liquids may cause switching delays.

‣Make sure that the liquid can run off the tuning fork easily.

‣Deburr the socket surface.

The tuning fork must be located outside the installation socket!

> 40 (1.57)

A0042335

 4 Installation example for a highly viscous liquid. Unit of measurement mm (in)

5.1.3 Avoid buildup

A0042345

 5 Installation examples for a highly viscous process medium

Mounting Liquiphant FTL64

10 Endress+Hauser

5.1.4 Take clearance into consideration

A0042340

 6 Take clearance outside the tank into consideration

5.1.5 Support the device

NOTICE

If the device is supported incorrectly, shocks and vibrations can damage the coated

surface.

‣Only use suitable supports.

Support the device in the event of severe dynamic load. Maximum lateral loading capacity of

the pipe extensions and sensors: 75 Nm (55 lbf ft).

Andere Handbücher für Liquiphant FTL64

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser LPGmass Bedienungsanleitung

Endress+Hauser

Endress+Hauser probfit CPA 463S Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar S Technische Daten

Endress+Hauser

Endress+Hauser RIA46 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Gammapilot FMG50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Waterpilot FMX21 Technische Daten

Endress+Hauser

Endress+Hauser Proline Promag 50H Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Technische Daten

Endress+Hauser

Endress+Hauser Nivector FTI26 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Promass 84F Handbuch

Endress+Hauser

Endress+Hauser Cerabar M PMC41 Bedienungsanleitung

Endress+Hauser

Endress+Hauser COM280 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 83 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Technische Daten

Endress+Hauser

Endress+Hauser Cerabar PMC71B Technische Daten

Endress+Hauser

Endress+Hauser Cerabar S PMP75 Technische Daten

Endress+Hauser

Endress+Hauser Proline Promag 50H Handbuch

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Gebrauchsanweisung

Endress+Hauser

Endress+Hauser Hart Cerabar PMP71B Bedienungsanleitung

Endress+Hauser

Endress+Hauser prosonic flow 92 Handbuch

Endress+Hauser

Endress+Hauser Prolevel FMC 662 Bedienungsanleitung

Endress+Hauser

Endress+Hauser PROFIBUS PA Levelflex FMP56 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant M FTM50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Waterpilot FMX21 Technische Daten

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung

Uniks

Uniks C126 Bedienungsanleitung