Endress+Hauser Memosens COS81E Bedienungsanleitung

Products Solutions Services

Operating Instructions

Memosens COS81E

Hygienic, optical sensor with Memosens 2.0 technology

for the measurement of oxygen

BA02066C/07/EN/01.20

71496967

2020-09-02

Memosens COS81E Table of contents

Endress+Hauser 3

Table of contents

1 About this document ................ 4

1.1 Warnings ............................ 4

1.2 Symbols used .......................... 4

1.3 Supplementary documentation ............. 4

2 Basic safety instructions ............ 6

2.1 Requirements for personnel ............... 6

2.2 Designated use ........................ 6

2.3 Workplace safety ....................... 6

2.4 Operational safety ...................... 6

2.5 Product safety ......................... 7

3 Product description ................. 8

3.1 Measuring principle ..................... 8

3.2 Product design ......................... 9

3.3 Stabilization time ....................... 9

3.4 Memosens technology .................. 10

4 Incoming acceptance and product

identification ..................... 11

4.1 Incoming acceptance ................... 11

4.2 Product identification ................... 11

4.3 Scope of delivery ...................... 12

4.4 Certificates and approvals ............... 12

5 Installation ....................... 13

5.1 Installation conditions .................. 13

5.2 Mounting the sensor ................... 14

5.3 Installation examples ................... 16

5.4 Post-installation check .................. 19

6 Electrical connection .............. 20

6.1 Connecting the sensor .................. 20

6.2 Ensuring the degree of protection .......... 20

6.3 Post-connection check .................. 20

7 Commissioning .................... 21

7.1 Function check ....................... 21

7.2 Calibration and adjustment .............. 21

8 Diagnostics and troubleshooting ... 25

8.1 General troubleshooting ................. 25

9 Maintenance ...................... 26

9.1 Maintenance schedule .................. 26

9.2 Maintenance tasks ..................... 26

10 Repair ............................ 28

10.1 General information ................... 28

10.2 Return .............................. 28

10.3 Spare parts .......................... 28

10.4 Disposal ............................ 32

10.5 Checking the measurement function ....... 32

11 Accessories ....................... 33

11.1 Device-specific accessories ............... 33

12 Technical data .................... 36

12.1 Input ............................... 36

12.2 Performance characteristics .............. 36

12.3 Environment ......................... 36

12.4 Process ............................. 37

12.5 Mechanical construction ................ 37

About this document Memosens COS81E

4 Endress+Hauser

1 About this document

1.1 Warnings

Structure of information Meaning

LDANGER

Causes (/consequences)

If necessary, Consequences of

non-compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation will result in a fatal or serious

injury.

LWARNING

Causes (/consequences)

If necessary, Consequences of

non-compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation can result in a fatal or serious

injury.

LCAUTION

Causes (/consequences)

If necessary, Consequences of

non-compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or more serious injuries.

NOTICE

Cause/situation

If necessary, Consequences of

non-compliance (if applicable)

‣Action/note

This symbol alerts you to situations which may result in damage to

property.

1.2 Symbols used

Symbol Meaning

Additional information, tips

Permitted or recommended

Not permitted or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

1.2.1 Symbols on the device

Symbol Meaning

Reference to device documentation

1.3 Supplementary documentation

The following manuals which complement these Operating Instructions can be found on

the product pages on the Internet:

• Technical Information for the relevant sensor

• Operating Instructions for the transmitter used

• Operating Instructions for the cable used

Memosens COS81E About this document

Endress+Hauser 5

In addition to these Operating Instructions, an XA with "Safety instructions for electrical

apparatus in the hazardous area" is also included with sensors for use in the hazardous

area.

‣Please follow instructions on use in the hazardous area carefully.

Safety instructions for electrical apparatus in hazardous areas, Memosens 2.0 optical

oxygen for ATEX and IECEx approval: XA02238C

Basic safety instructions Memosens COS81E

6 Endress+Hauser

2 Basic safety instructions

2.1 Requirements for personnel

• Installation, commissioning, operation and maintenance of the measuring system may

be carried out only by specially trained technical personnel.

• The technical personnel must be authorized by the plant operator to carry out the

specified activities.

• The electrical connection may be performed only by an electrical technician.

• The technical personnel must have read and understood these Operating Instructions

and must follow the instructions contained therein.

• Faults at the measuring point may only be rectified by authorized and specially trained

personnel.

Repairs not described in the Operating Instructions provided must be carried out only

directly at the manufacturer's site or by the service organization.

2.2 Designated use

Use of the device for any purpose other than that described, poses a threat to the safety of

people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Workplace safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

• Regulations for explosion protection

Electromagnetic compatibility

• The product has been tested for electromagnetic compatibility in accordance with the

applicable international standards for industrial applications.

• The electromagnetic compatibility indicated applies only to a product that has been

connected in accordance with these Operating Instructions.

2.4 Operational safety

Before commissioning the entire measuring point:

1. Verify that all connections are correct.

2. Ensure that electrical cables and hose connections are undamaged.

3. Do not operate damaged products, and protect them against unintentional operation.

4. Label damaged products as defective.

During operation:

‣If faults cannot be rectified:

products must be taken out of service and protected against unintentional operation.

Memosens COS81E Basic safety instructions

Endress+Hauser 7

2.5 Product safety

2.5.1 State-of-the-art technology

The product is designed to meet state-of-the-art safety requirements, has been tested, and

left the factory in a condition in which it is safe to operate. The relevant regulations and

international standards have been observed.

Product description Memosens COS81E

8 Endress+Hauser

3 Product description

3.1 Measuring principle

Sensor structure

Oxygen-sensitive molecules (markers) are integrated into the optically active layer

(luminescence layer).

The luminescence layer, an optical insulating layer and a cover layer are applied on top of

one another on the carrier. The cover layer is in direct contact with the medium.

The sensor optics are directed at the rear of the carrier and therefore at the luminescence

layer.

Measurement process (principle of luminescence quenching)

If the sensor is immersed in the medium, an equilibrium is very quickly established

between the oxygen partial pressure in both the medium and the luminescence layer.

1. The sensor optics send orange light pulses to the luminescence layer.

2. The markers "respond" (luminesce) with dark-red light pulses.

 The decay time and intensity of the response signals are directly dependent on

the oxygen contents and oxygen partial pressure.

If the medium is free from oxygen, the response signals are long and very intense.

If the medium is free from oxygen, the decay time is long and the signal is very intense.

Any oxygen molecules present mask the marker molecules. As a result, the decay time is

shorter and the signals are less intense.

Measurement result

‣The sensor calculates the measurement result on the basis of the signal intensity and

decay time using the Stern-Volmer equation.

The air pressure can be either set statically or entered via an additional sensor. The

medium temperature is automatically recorded in the sensor. Both values are taken into

consideration in the calculation of the oxygen concentration.

The sensor provides measured values for temperature and partial pressure as well as a raw

measured value. This value corresponds to the luminescence decay time and is approx.

14 μs in air and approx. 56 μs in oxygen-free media.

For optimum measurement results

1. During calibration, enter the current air pressure at the transmitter.

2. If the calibration is not performed at Air 100% rh:

Enter the current humidity.

3. In the case of saline media:

Enter the salinity.

4. For measurements in the units %Vol or %SAT:

Also enter the current operating pressure in the measuring mode.

Observe the documentation of the transmitter used:

• Operating Instructions for Memosens: BA01245C

For all transmitters, analyzers and samplers in the Liquiline CM44x/P/R, Liquiline

System CA80XX and Liquistation CSFxx product families

• Operating Instructions for Liquiline CM42, BA00381C and BA00382C

• Operating Instructions for Liquiline Mobile CML18: BA02002C

• Operating Instructions for Liquiline Compact CM82: BA01845C

• Operating Instructions for Liquiline Compact CM72: BA01797C

Memosens COS81E Product description

Endress+Hauser 9

3.2 Product design

1 2 34

8 5

A0027181

 1 Memosens COS81E

Memosens plug-in head with optics assembly

Thrust collar

Sensor shaft

O-ring sensor shaft

Spot cap

Optical waveguide with temperature sensor

Process seal 10.77 x 2.62 mm

Process connection Pg 13.5

The suitability of the selected materials for use in the process must be assessed during

the product configuration.

Process conditions that go beyond the resistance range of the materials may shorten

the operating life of the materials and make maintenance necessary.

3.2.1 Spot cap

The oxygen dissolved in the medium is diffused to the luminescence layer of the spot cap.

A suitable flow is not required, as no oxygen is consumed during measurement. However,

flow improves the speed at which the measuring system reacts and ensures a more

representative measured value compared to a measurement in a static medium.

The spot is permeable for dissolved gases only. Other substances dissolved in the liquid

phase, such as ionic substances, will not penetrate through the membrane. Therefore,

medium conductivity has no impact on the measuring signal.

The sensor's spot cap can have either a c-shaped or u-shaped design.

A0034733

 2 Design of spot cap

1 u-shaped

2 c-shaped

3.3 Stabilization time

The measuring method used by the sensor is temperature-dependent. For this reason, the

temperature of the sensor must be adapted to the medium temperature during

commissioning. You obtain reliable measured values once a stable temperature value is

reached.

The temperature usually adapts very quickly in aqueous media. Temperature adaptation

can take several minutes in gaseous media.

Product description Memosens COS81E

10 Endress+Hauser

3.4 Memosens technology

Sensors with Memosens protocol have an integrated electronics unit that stores calibration

data and other information. Once the sensor has been connected, the sensor data are

transferred automatically to the transmitter and used to calculate the measured value.

‣Call up the sensor data via the corresponding DIAG menu.

Digital sensors can store measuring system data in the sensor. These include the following:

• Manufacturer data

• Serial number

• Order code

• Date of manufacture

• Calibration data

• Calibration date

• Calibration values

• Number of calibrations

• Serial number of the transmitter used to perform the last calibration or adjustment

• Operating data

• Temperature application range

• Date of initial commissioning

• Hours of operation under extreme conditions

Andere Handbücher für Memosens COS81E

Inhaltsverzeichnis

Andere Endress+Hauser Messgerät Handbücher

Endress+Hauser

Endress+Hauser Flexdip CYA112 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline t-mass 65 PROFIBUS DP Bedienungsanleitung

Endress+Hauser

Endress+Hauser prolevel FMC 661 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass 83 Stücklistenhandbuch

Endress+Hauser

Endress+Hauser Oxymax COS61D Bedienungsanleitung

Endress+Hauser

Endress+Hauser CE 4 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex M FMP41C Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass E 100 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Technische Daten

Endress+Hauser

Endress+Hauser Conducal CLY421 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promass E 100 Bedienungsanleitung

Endress+Hauser

Endress+Hauser RID14 Technische Daten

Endress+Hauser

Endress+Hauser Micropilot FMR10 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar PMD55B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 10 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 10 Technische Daten

Endress+Hauser

Endress+Hauser Cerabar PMP51B Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 500 Technische Daten

Endress+Hauser

Endress+Hauser Micropilot FMR20 Handbuch

Endress+Hauser

Endress+Hauser Cerabar S PMP71 with MID Part Certificate Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltatop DP71B Handbuch

Endress+Hauser

Endress+Hauser Proline Promass 80E Handbuch

Endress+Hauser

Endress+Hauser Micropilot FMR67 Handbuch

Endress+Hauser

Endress+Hauser RIA 450 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung