Eneo IAM-6MC1001MTA Bedienungsanleitung
Package
Quick
Installation
Guide
EPoC Extender
(Transmitter / Receiver)
Bracket
& Screw
Quick Installation
Guide
Hardware Overview
Right
Left
56V DC
Bracket
NO ANALOG
CAMERA
ETHERNET
PoE-ON
Data-Link
Join-Link
Power
PoE
Bracket
Join
ON OFF
브라켓 홀
브라켓 홀
RJ45
Join 버튼
상태 표시등
DC 전원 어댑터
PoE ON/OFF 스위치
(ECP-2601T 전용)
PoE-ON (ECP-2601T)
PD-AUX (ECP-2601R)
Bracket Hole DC Power Jack
Bracket Hole Join Button
Status LED Indicator
PoE ON/OFF Switch
(Transmitter model only)
PoE-ON (Transmitter model only)
PD-AUX (Receiver model only)
Overview
EPoC Extender is a High-Speed, long distance Ethernet & PoE extender that
makes possible to transmit the Ethernet signal up to 2.4Km and PoE up to
1.2Km via Coax (or UTP, 2wire & Etc.) cables in different situations.
It is cost-effective and time saving solution to migrate existing analog system
to IP based system since EPoC Extender supports easy installation utilizing
the existing cable.
With long distance transmission feature, the device makes to overcome 100
meters distance limitation easily and reduces the construction cost
significantly compared with fiber optic configuration.
Features
Ethernet over Coax communication following IEEE1901 Standard
Data + Power over Coax cable (or UTP, 2-Wire)
Data distance up to 2.4Km
PoE distance up to 1.2Km
Max. 95Mbps Bandwidth
10/100 Full Duplex
128bit AES network encryption
Supports Multi-connection (Daisy chain, Star, etc.)
PoE, PoE+, Extra PoE (Max. 60W output) - Transmitter model only
Supports UTP, Telephone (2 Pairs), 2-Wire cable communication
(Using BTE Series)
LED Indication (PoE, Data, Join, Power)
Plug & Play
Surge Protection
Support PoE+ Input (25.5W) from PSE devices (PoE Switch or Injector)
– Receiver model only
Slim design
Quick Installation Guide
Ethernet Coax Transmitter/Receiver,
Data & Power over Coax,
1 x RJ-45, 1 x BNC
IAM-6MC1001MTA
IAM-6MC1001MRA
Please read carefully the instruction manual before use. Depending
on the model, the image and the actual look of the product may vary.
LED Indicators
Indicator Color Function
PoE-ON PoE Output Status (Transmitter model on ly)
PD-AUX PoE Input Status (Receiver model only)
Data-Link Blinks when transmitting Ethernet data
Join-Link EPoC products connected
Power 56VDC or PoE Input connected
Installation Guide
1. Set the IP address on the camera following the instruction manual
of the camera.
Î
If the camera IP is automatically assigned (DHCP, etc.), there is no
need to set the camera IP separately.
2. Connect BNC of the coaxial cable to each Transmitter/Receiver.
3. Connect 56V DC power to Transmitter/Receiver first and then to
AC outlet.
Î
Receiver can be powered by PoE Switch Device (PoE+ PD
Supported) but for safe working, it recommeded to use 56VDC
Power supply on Receiver. When using both PoE switch Device and
power supply at the same time, power supply works preferentially.
Î
In case of 7W camera, the device supports long distance PoE
transmission up to 1,200m over RG6 coaxial cable.
PoE transmission distance can be varied depending on cable type
and Camera’s power consumption(W).
Î
Please download full manual for more information about PoE
distance by various cables.
4. When they are connected without any problem, Power / Join Link
LED are on.
5. Adhere the brackets in the package to Transmitter/Receiver and
then fix up the products.
6. Connect the UTP(LAN) cable between Receiver and NVR first and
then between Transmitter and camera.
7. Turn on the PoE switch on Transmitter for PoE IP camera and if the
camera is powered by a separate power source (not powered by
PoE output feature of the Transmitter), turn off the PoE switch on
Transmitter.
Î
Both Transmitter/Receiver send data and power together via BNC
connector. Receiver does not have PoE support so that it can send
data only via RJ45.
8. Ping test is recommended to confirm the whole network after
installation.
9. Check the video signal on the monitor.
Caution
Please install the device following the installation guide.
Do not touch the device and cable with wet hands.
Keep away from moisture and shock.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat.
Indoor use only.
Do not use for other purposes.
Do not disassemble or modify this device.
Do not put any sticker or paint on it.
If this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
Please use the rated power supply for the product.
Connect DC power to this device first and then to AC outlet.
Warranty
This device has passed the quality control and product inspection.
Please install and use according to the installation guide.
The warranty period for this product is 24 months from the date of
purchase.
If this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
Any damages or breakage from user’s abuse, accident, modification
or natural disasters will not be covered manufacturer’s warranty.
This device complies with part 15 of the fcc rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference that
may cause undesired operation
Applications
AC/DC
Adapter(12V)
Non-PoE IP
Camera
Coaxial Cable
Coaxial Cable
10/100 Ethernet
10/100 Ethernet
PoE
ECP-2601R
56V DC/1.2A
Power Supply
NVR
ECP-2601T ECP-2601R
ECP-2601T
PoE
Camera
PoE Switch
PoE : OFF
PoE : ON
PoE
Input Power
DC Adapter
Input Power
Transmitter
Transmitter Receiver
Receiver
Specification
Model Transmitter Receiver
Interface Coax 1 x 75Ω BNC (Female) - Ethernet over Coax (B-LinX)
Ethernet 1 x RJ45 - 10/100 Base-T with Auto-detect MDIX
Transmission Rate 95Mbps Full Duplex
Transmission
Distance
Ethernet up to 2.4Km(RG-6)
PoE (PoC) up to 1.2Km (RG-6 / 7W camera)
LED
Indication
Ethernet 1 x Data-Link (Yellow)
EPoC 1 x Join-Link (Green)
Power 1 x Power On(Amber)
PoE 1 x PoE Out (Red)
Encryption 128-bit AES
Power
Input B-Linx or DC12V~57V PoE Switch or
DC12V~57V
PoE Output Extra PoE up to 60W PoE Not Supported
PoC Only
Me chanical Dimension 82.4(L) x 61.6(W) x 24(H)mm
Weight 77g
Environment
Operating Temp -20 ~ 60°C
Storage Temp -30 ~ 80°C
Relative Humidity 10% ~ 90%
Compliance Certification FCC, CE, KC, RoHS
Surge Protection IEC 61000-4-5 4kV(1.2 / 50us), 2kA(8 / 20us)
Optional Accessorie s 56VDC / 1.2A External Power Supply
eneo® is a registered trademark of VIDEOR E. Hartig GmbH
Exclusive distribution through specialised trade channels only.
VIDEOR E. Hartig GmbH, Carl-Zeiss-Straße 8, 63322 Rödermark/Germany
Tel. + 49 (0) 6074 / 888-0
Fax +49 (0) 6074 / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig GmbH Version 09/2019
How to change the communication password
EPoC Extender have the same password as factory defaults setting value
and can be used immediately when connecting to the product (Plug & Play
mode). However, if a number of products are mixed in the same area or the
signal transmission line is in poor condition, the communication
passwords for each equipment (or group) can be set differently to prevent
cross-talk between the lines.
1. Needed items for Joining
EPoC Converters / Power supply / Short Cable (Coax, UTP, 2-Wire) / Paper
clip.
2. Product configuration
a. Connect EPoC Converters with Coax cable (or UTP, 2-Wire) and power
to the one of the converters up with power supply.
b. Check if the Power LED on both devices is ON.
3. Remove the existing password (Unjoining)
This process removes passwords that are entered as factory defaults.
a. Press the Join button on one of the connected products using a paper
clip until the Power LED turns off and on (Approximately 15 seconds)
b. Remove the existing password by pressing the Join button on the
opposite product in the same way as above.
c. Join LED will be turned off if the password on the devices is removed
correctly.
4. Create New Password (Joining)
New password for communication between connected devices is created
and this will block the communication with other devices (or group) which
have a different password.
a. Press the Join button for 2 seconds on one of the connected product
using a paper clip and the Join LED of the device will flicker at a
constant speed. (Stand-by mode)
b. Press the Join button for 2 seconds on the opposite device in the same
way as above. And then, the Join LED of the device flickers at a
constant speed and both devices restart at the same time.
c. Then the Join-Link lights up and communications are resumed
between the products
5. When adding new products in 1:N configuration to a group that has
already been joined. (Group Joining)
a. Connect new device to the group which is already joined. (using
T-BNC or Y-UTP coupler, Terminal block)
b. Remove the password of the new device in the same way as step ‘3-a’.
c. Press Join button on the one of the device of the existing group for 2
seconds and Join LED flickers at a constant speed.
d. Press Join button on the new device for 2 seconds and new device
restarts
e. Join-Link lights up and communications are resumed between the
prod ucts.
Andere Handbücher für IAM-6MC1001MTA
1
Dieses Handbuch passt für folgende Modelle
3
Andere Eneo Empfänger Handbücher
