EnGenius ENH500 Einrichtungshandbuch

Andere Handbücher für ENH500

8

Andere EnGenius Drahtloser Zugangspunkt Handbücher

EnGenius

EnGenius ENH500 Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

EnGenius

EnGenius EOC-5610 Bedienungsanleitung

EnGenius

EnGenius caprive portal ready Bedienungsanleitung

EnGenius

EnGenius ENS200 Bedienungsanleitung

EnGenius

EnGenius EAP1750 Bedienungsanleitung

EnGenius

EnGenius M2000 Bedienungsanleitung

EnGenius

EnGenius EOC5611P Bedienungsanleitung

EnGenius

EnGenius ENH200 Bedienungsanleitung

EnGenius

EnGenius EWS371AP Bedienungsanleitung

EnGenius

EnGenius ENS500 Bedienungsanleitung

EnGenius

EnGenius EOC-2610 Bedienungsanleitung

EnGenius

EnGenius ENH1350EXT Bedienungsanleitung

EnGenius

EnGenius ENS202EXT Bedienungsanleitung

EnGenius

EnGenius EAP600 Bedienungsanleitung

EnGenius

EnGenius Neutron EWS320AP Bedienungsanleitung

EnGenius

EnGenius ENS1750 Bedienungsanleitung

EnGenius

EnGenius ENS202 Bedienungsanleitung

EnGenius

EnGenius EAP9550 Bedienungsanleitung

EnGenius

EnGenius ECB7510 Bedienungsanleitung

EnGenius

EnGenius X-TRA RANGE ERB300H Bedienungsanleitung

EnGenius

EnGenius M5000 Bedienungsanleitung

EnGenius

EnGenius ENH500 Bedienungsanleitung

EnGenius

EnGenius ETR9330 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

1

How to Set up WDS Bridge on a ENH-500 (P2P)

Point-to-Point WDS Bridge should have a physical topology similar to

the picture below:

2

Please note that in order for the settings to save on this unit you need

to click save/apply under the save/reload option under Status.

3

Step #1:

Note the MAC address under the wireless MAC address field for each unit.

Step #2:

Change the IP address of each unit to be in the same subnet as your network,

outside the DHCP scope

4

Step #3:

Change the mode of operation to WDS Bridge.

Step #4:

Set the channels to be the same on all units in the WDS link.

5

Step #5:

Here is WDS link settings of device A with the Wireless MAC address of device B

in the MAC address field.

Step #6:

Here is device B WDS link settings page with Device’s A wireless MAC address

entered.

6

Step #7:

To test the link ping across the link

Step #8:

Your ping should have zero packet loss

7

Optional:

If you want encryption on your WDS link, then select the encryption method

under the security drop down menu, then the WEP key or WPA passphrase.

Note the unit will revert to G speeds when using WEP, N speeds is only

supported by AES. This has to match on both units if you chose to enable it on

one unit:

If you have trouble with your WDS Bridge link then try changing both units

channel HT from 40 Mhz to 20 Mhz.

8

If you are still experiencing problems with your WDS link, then try changing to a

non-DFS channel, and then lastly try changing the band of the units from A/N to

A only.

9

Use the following chart to determine non DFS channels. Use the FCC column.

Please keep in mind if using the 5GHz band that channels 52-140 are UNI –2

channels which radar systems commonly operate on. There is an FCC

mandated function called DFS that automatically changes the channel of any

5GHz WiFi radio including any and all EnGenius radios if radar is detected as to

avoid interference to radar systems.

The best channels to use are 34-48 and 149-165.