Entity FS60 Bedienungsanleitung
FS60 2-BIKE STAND
USER MANUAL
ENTITY FS60 2-BIKE STAND
2
PARTS LIST
1. Ceiling Pad
2.Optional Ceiling Fixing Screw
3. Ceiling Pad Spring
4. Upper Tube
5. Upper QR Clamp Lever
6. Middle Tube (ø44 mm)
7. Hook Unit Adaptor (ø44 mm)
7.1Hook Unit Mounting Device
7.2Adjusting Knob
8. Lower QR Clamp Lever
9. Hook Unit Adaptor (ø50 mm)
9.1 Hook Unit Mounting Device
9.2 Adjusting Knob
10. Lower Tube
11. Height Adjuster Dial
12. Optional Foot Fixing Screws
13. Rubber Foot Pad
14. Hook Unit
14.1 Hook
14.2 Hook Locking Bolt
14.3 M6 Hook Unit Fixing Bolt
14.4 Washer
10
11
13
6
8
5
4
14
7
9
14
1
3
© ENTITY 2019
ENTITY FS60 2-BIKE STAND
3
HOOK UNIT (#14)
14.1
7.2
14.1
7.1
14.2
14.2
14.3
HOOK UNIT ADAPTOR (#7/9)
ENTITY FS60 2-BIKE STAND
4
WARNING
1. Failure to completely follow any of these instructions or to heed
any of the warnings in this User’s guide may cause the stand
and bicycles to fall and may result in serious physical injury,
death and/or property damage.
2. The product as installed must be vertically straight up and
down at all times.
3. Install product against a ceiling joist or beam. Failure to do so
may cause damage to your ceiling and the stand to fall.
4. Install only against smooth and level surface. Failure to do so
may cause the stand and bicycles to fall.
5. Never use for any other purpose than the storage of bicycles.
6. No more than one bicycle may be hung on each hook.
7. Do not install in any area to which children have access.
8. Never install in an area where it may be accidentally kicked,
bumped or otherwise mishandled.
9. Bumping into the stand may cause it to fall. If the stand
is accidentally bumped, check the stability of the stand in
accordance with these instructions to ensure that it is secure.
10. Check the stand frequently in accordance with this user’s guide
to ensure that it is secure.
ENTITY FS60 2-BIKE STAND
5
FIRST TIME INSTALLATION
Install FS60 bike stand against solid
ceiling construction
INSTALLING MAIN UNIT
1. Release the Upper and/or Lower QR Clamp
Lever and extend the stand until the Ceiling
Pad Spring is compressed against the solid
ceiling.
2. Lock both the Upper and Lower QR Clamp
Levers rmly. If tubes slide, release the QR
Clamp Lever, tighten the threaded nut and
lock the QR Clamp Lever again.
3. Once at the nal height, use the 3mm Hex
Key to tighten the Grub Screws adjacent to
the QR Clamp Levers
4. Rotate the Height Adjuster Dial counter-
clockwise until the Ceiling Pad Spring is
fully compressed
The maximum height of the FS60 bike
stand is 3.4m.
ENTITY FS60 2-BIKE STAND
6
ASSEMBLING HOOK UNITS
ENTITY FS60 2-BIKE STAND
7
ADJUSTING HOOK UNIT
ADJUSTMENT OPTIONS
Using the release knob grips, turn the grip counter-clockwise to
losen the grip, clockwise to secure the part.
In this way you can adjust the width and position of the individual
hooks, as well as the height and rotation of the complete hook
assembly.
ENTITY FS60 2-BIKE STAND
8
CAUTION
1. Install FS60 bike stand against a ceiling joist or beam. Never
install against a fragile ceiling or on a non-solid or rough
surface.
2. Always make sure Middle Tube and Upper Tube are securely
locked in place. Improper fastening may cause QR clamp lever
and tension bolts to loosen resulting in collapse of stand.
3. Always balance bike on its hook.
4. When removing or repositioning FS60 bike stand always
remember to remove the bike(s)!
5. The adjusting knob should not be overtightened.
6. If unable to loosen adjusting knob, loosen mounting bolts rst,
then loosen adjusting knob.
7. Hold main tube securely when removing or repositioning FS60
bike stand.
8. The maximum height of the FS60 bike stand is 3.4m. Please
measure height of your ceiling from floor before installing.
9. Maximum weight capacity per Hook Unit is 25kg.
10. No more than one bicycle may be hung on each hook.
11. Caution should be taken when mounting the FS60 bike stand
in areas with high vibration either near the base or the top
of the FS60 bike stand. Automatic garage door openers, air
compressors, etc., may cause enough vibration to cause the
FS60 bike stand to move. Periodically check the stability of
the FS60 bike stand if near a vibration source to ensure safe
storage of your bicycles.
12. Check the stability of the FS60 bike stand by lightly pulling and
pushing the vertical bar. Remove any bicycles on the FS60 bike
stand before testing stability. The foot or top should not be able
to move when in the locked position. If the FS60 bike stand is
loose, reinstall the main unit and test again. Periodically check
the stability of the FS60 bike stand to ensure safe storage of
your bicycles.
Inhaltsverzeichnis
Andere Entity Fahrradzubehör Handbücher
Beliebte Fahrradzubehör Handbücher anderer Marken
Sigma
Sigma BC 16.16 Bedienungsanleitung
Playcore
Playcore Dero Setbacks Bedienungsanleitung
VDO Cyclecomputing
VDO Cyclecomputing x3dw Bedienungsanleitung
Cateye
Cateye RAPID X2 Bedienungsanleitung
buratti meccanica
buratti meccanica Clorofilla Trail Bedienungsanleitung
Shimano
Shimano SG-8R20 Betriebsanleitung
