Enviro Solus Bedienungsanleitung

PELLET STOVE

SOLUS

PLEASE READ THIS ENTIRE MANUAL BEFORE

INSTALLATION AND USE OF THIS PELLET BURNING

ROOM HEATER. FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,

BODILY INJURY, OR EVEN DEATH.

Contact your building or fire officials about restrictions and installation

inspection requirements in your area.

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED

PAPER.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

OWNER’S MANUAL

50-039

Table of Contents

Introduction..............................................................................................................3

Pellet Quality..................................................................................................3

Rating Label Location......................................................................................3

Important Safety Data....................................................................................3

Introduction..............................................................................................................4

Safety Warnings And Recommendations...........................................................4

Deciding Where to Locate your Pellet Appliance................................................6

Removing Pellet Stove From Pallet...................................................................6

Dimensions....................................................................................................7

Clearances to Combustibles.............................................................................7

Alcove Clearances...........................................................................................8

Vent Termination Requirements.......................................................................9

Outside Fresh Air Connection.........................................................................10

Mobile Home Installation...............................................................................10

Horizontal Exhaust Through The Wall.............................................................10

Through Wall Installation...............................................................................12

Inside Vertical Pipe Installations.....................................................................13

Outside Vertical Pipe Installations...................................................................14

Installation of Door A....................................................................................15

Operating Instructions.............................................................................................16

Automatic Safety Features.............................................................................16

Slider/Damper Setting...................................................................................16

Operating Instructions...................................................................................17

Operating Your Pellet Stove...........................................................................17

Turning Your Pellet Stove Off.........................................................................17

Routine Cleaning and Maintenance...........................................................................18

Troubleshooting.......................................................................................................20

Part List..................................................................................................................24

Wiring Diagram.......................................................................................................25

Warranty.................................................................................................................26

Installation Data Sheet.............................................................................................27

PELLET QUALITY IS IMPORTANT, PLEASE READ

YOUR ENVIRO PELLET STOVE HAS BEEN DESIGNED TO BURN WOOD PELLETS ONLY. DO

NOT USE ANY OTHER TYPE OF FUEL, AS THIS WILL VOID ANY WARRANTIES STATED IN

THIS MANUAL.

Since there are many manufacturers of wood pellets it is important to select pellets that are free of

dirt or any impurities. The Pellet Fuel Industries (P.F.I.) has established standards for wood pellet

manufactures. We recommend the use of pellets that meet or exceed these standards. Ask your dealer

for a recommended pellet type.

THE PERFORMANCE OF YOUR PELLET STOVE IS GREATLY AFFECTED BY THE TYPE AND QUALITY

OF WOOD PELLETS BEING BURNED. AS THE HEAT OUTPUT OF VARIOUS QUALITY WOOD PELLETS

DIFFERS, SO WILL THE PERFORMANCE AND HEAT OUTPUT OF THE PELLET STOVE.

Since Sherwood Industries Ltd. has no control over the quality of pellets that you use, we assume no

liability caused by the quality of wood pellets used.

P.F.I. PELLET STANDARDS:

Fines..................................... 1% maximum through a 1/8” screen

Bulk Density.......................... 40 lbs. per cubic foot minimum

Size....................................... ” to ” diameter 1 – 1” long maximum

Ash Content .......................... 1% maximum

Moisture Content .................. 8% maximum

Heat Content......................... approximately 8200 Btu per lb. minimum

Check the burn-pot liner periodically to ensure that the holes are not blocked with clinkers (clinkers are

silica in the fuel that will form a hard mass during the burning process). If they are blocked, remove the

liner (when the unit is cold) and clean the clinkers out. The liner should be cleaned or scraped once every

2-3 days depending on wood pellet quality. Clean the holes in the lines with a small pointed object.

Store pellets at least 36” (1 m) away from the pellet stove.

Introduction

PELLET QUALITY:

RATING LABEL LOCATION:

The rating label is located on the inside of the hopper lid.

IMPORTANT SAFETY DATA:

To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the

installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information with

regards to your local building codes and installation restrictions.

The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive

chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight.

This unit is designed to burn pelletized wood fuel only. Do not use any other type of fuel, this will void any

warranties stated in this manual.

Fuel: This pellet stove is designed and approved to only burn wood pellet fuel with up to 3% ash

content. Dirty fuel will adversely affect the operation and performance of the unit and may void the

warranty. Check with your dealer for fuel recommendations.

THE USE OF CORDWOOD IS PROHIBITED BY LAW.

Soot: Operation of the stove with insufficient combustion air will result in the formation of soot which

will collect on the glass, the heat exchanger, the exhaust vent system and may stain the outside of the

house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/

damper as needed to ensure proper combustion. See: “Operation - Slider/Damper”

Exhaust Cleaning: There will be some build up of fly ash and small amounts of creosote in the exhaust.

This will vary due to the ash content of the fuel used and the operation of the stove. It is advisable to

inspect and clean the exhaust vent annually or every two tons of pellets.

Ashes: Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed container

of ashes should be on a non-combustible floor on the ground, well away from all combustible materials,

pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispensed, they

should be retained in the closed container until all cinders have been thoroughly cooled.

Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper

combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by

adjusting the slide damper located on the left side of the stove.

It is advisable to clean the exhaust vent bi-annually or every two tons of pellets.

The grounded electrical cord should be connected to a standard 115 volts, 60-hertz electrical outlet. Be

careful that the electrical cord is not trapped under the appliance and that it is clear of any hot surfaces

or sharp edges and also must be accessible. If this power cord should become damaged a replacement

power cord must be purchased from the manufacture or a qualified ENVIRO dealer. The SOLUS’s

maximum power requirement is 550 watts.

Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as an

extremely rich burn (black tipped, lazy orange flames).

When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the

home and bolted to the floor. Make sure that the structural integrity of the home is maintained.

Be sure to maintain the structural integrity of home when passing a vent through walls, ceilings, or

roofs.

The ash pan must be locked securely for proper and safe operation of the pellet stove.

If you have any questions with regards to your stove or the above-mentioned information, please feel

free to contact your local dealer for further clarification and comments.

SAFETY WARNINGS AND RECOMMENDATIONS:

Introduction

Electrical: THE USE OF A SURGE PROTECTED POWER BAR IS RECOMMENDED.

The maximum power requirement is 550 watts (4.6 amp). The stove has a grounded electrical cord and

should be connected to a standard 115 volt, 60-Hz grounded electrical outlet. Make sure the electrical

cord is not trapped under the appliance and that it is clear of any hot surfaces or sharp edges. When

installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the home

and bolted to the floor in accordance with applicable local, state or federal codes.

Glass: Do not attempt to open the door and clean the glass while the unit is in operation. To clean the

glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner or take a damp

paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the glass. Do not

abuse the glass by striking or slamming the door. Do not attempt to operate the stove with broken glass.

The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO dealer. Do not

attempt to open the door and clean the glass while the unit is in operation or if glass is hot.

Flammable Liquids: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid,

or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from the

heater while it is in use.

Smoke Detector: Smoke detectors should be installed and maintained in the structure when installing

and operating a pellet burning appliance.

Operation: The ash pan and door must be closed securely for proper and safe operation of the pellet

stove. Also ensure all gaskets on the door are checked and replaced when necessary.

KEEP ASH PAN FREE OF RAW FUEL.

DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN ASH PAN. A fire in the ash pan may occur.

Installation: Be sure to maintain the structural integrity of your home when passing a vent through

walls, ceilings, or roofs. It is recommended that the unit be secured into its’ position in order to avoid

any displacement.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

Fresh air: Must be connected to all units installed in Mobile Homes as well as “Air Tight Homes” (R2000).

Fresh air intake is recommended on all installations. Failure to install intake air may result in poor

performance, smoke, property damage, house fire, bodily injury or death under certain conditions.

If you have any questions with regards to your stove or the above-mentioned information, please feel

free to contact your local dealer for further clarification and comments.

SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF

YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED

FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD

INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

Introduction

1. Check clearances to combustibles.

2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may

be obtained from a ventilated crawlspace.

3. Do not install the stove in a bedroom.

4. You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry

or metal chimney (must be lined if the chimney is over 6” in diameter, or over 28 sq. inches cross

sectional area). An interior vent can be used with approved pipe passing through the ceiling and

roof.

5. Locate the stove in a large and open room that is centrally located in the house. This will optimize

heat circulation.

6. The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the

nearest electrical outlet.

Installation

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:

REMOVING PELLET STOVE FROM PALLET:

REMOVE

HOLDING

SCREWS TO

REMOVE

FROM PALLET

To remove your new stove from its pallet,

turn ash pan latch to open and remove Ash

Pan from unit. Remove two securing screws

from inside of the pedestal.

Installation

DIMENSIONS:

CLEARANCES TO COMBUSTIBLES:







 







 



This unit must be installed on a noncombustible hearth pad, extending at least 6” (inches) (150 mm) in

front of the appliance and at least the entire width of the appliance.

(A) Side wall to unit

- 6 INCHES (150 mm)

(B) Back wall to unit

- 2 INCH (50 mm)

(D) Front of hearth pad to unit

(Floor Protection)

- 6 INCHES (150 mm)

(D) Floor protection

6 INCHES (152 mm)

(E) Side wall to unit

6 INCHES (152 mm)

(F) Mantle to unit

10 INCHES (254 mm)

(G) Top facing to unit

8 INCHES (203 mm)

ALCOVE CLEARANCES:

Installation

Min. Alcove width........36 inches (900 mm)

Min. Alcove height......48 inches (1200 mm)

Min. Alcove depth.......48 inches (1200 mm)

48”

(120cm)

48”

(120cm)

36” (90cm)

A. Do not terminate the vent in any enclosed or semi-enclosed areas such as a carport, garage, attic, crawlspace, narrow

walkway, closely fenced area, under a sundeck or porch, or any location that can build up a concentration of fumes such as

stairwells, covered breezeway, etc.

B. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shielding or guards may be

required.

C. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of vertical pipe be installed

outside when the appliance is vented directly through a wall to create some natural draft. This will prevent the possibility of

smoke or odor during appliance shut down or power failure and will keep exhaust from causing a nuisance or hazard from

exposing people or shrubs to high temperatures. In any case, the safest and preferred venting method is to extend the vent

through the roof vertically.

D. Vent terminal cannot be:

•less than 4 feet (1.2 m) below

•less than 4 feet (1.2 m) horizontally from, and

•less than 1 foot (305 mm) above doors, window openings, or gravity/ventilation air inlet into building.

E. Distance from bottom termination and grade –12” (305 mm) minimum. This is conditional upon the plants and nature of

grade surface. The exhaust gases are hot enough to ignite grass, plants and shrubs located in the vicinity of termination. The

grade surface must not be lawn. Distance from bottom of termination and public walkways is 7 feet (2.1 m) minimum.

F. Distance to combustible materials is 2 feet (610 mm). This includes adjacent buildings, fences, protruding parts of the

structure, roof overhang, plants, shrubs, etc.

G. When installing an FPI the chimney must be fully lined. Unless the chimney’s inside diameter is less than 6” around or has a

cross section area of 28 square inches, we strongly recommend lining all masonry chimneys.

H. If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the exterior of the house

might occur. Since these factors are beyond Sherwood Industries LTD’s. control, we grant no guarantee against such

incidents.

IT IS RECOMMENDED THAT AN AUTHORIZED DEALER/INSTALLER INSTALL YOUR PELLET STOVE.

VENT TERMINATION REQUIREMENTS:

Installation

NOTE: Measure clearance to the nearest edge of the exhaust hood

A- MINIMUM 4 feet (1.2m) below or beside any door or window that opens.

B- MINIMUM 1 foot (305 mm) above any door or window that opens.

C- MINIMUM 2 feet (610 mm) from any adjacent buildings.

D- MINIMUM 7 feet (2.1 m) above grade when adjacent to public walkways.

(NOTE) Vent may not terminate in a covered walkway or breezeway.

E- MINIMUM 2 feet (610 mm) above plants, grass or other combustible materials.

F- MINIMUM 3 feet (915 mm) from any forced air intake of other appliances.

G- MINIMUM 2 feet (610 mm) below any eave or roof overhangs.

H- MINIMUM 1 foot (305 mm) clearance to a combustible wall.

W- MINIMUM 2 feet (610 mm) above the roof.

AFD

Outside fresh air is mandatory when installing

this unit in airtight homes and mobile homes.

When connecting to an outside fresh air source, do

not use plastic, combustible pipe. Only 1 ” ID

(inside diameter) steel, aluminum or copper pipe

should be used. It is recommended, when you are

installing a fresh air system, to keep the number of

bends in the pipe to a minimum.

Installation

OUTSIDE FRESH AIR CONNECTION:

● Secure the heater to the floor using the two holes in the pedestal. Do not disturb the structural integrity

of the home.

● Ensure the unit is electrically grounded to the chassis of your home (permanently).

● Do not install in a room people sleep in.

● Outside fresh air is mandatory.

MOBILE HOME INSTALLATION:

Optional

elbow

1-5/8”

diamter

1. Choose a location for your stove that meets the requirements stated in this manual and allows

installation with the least amount of interference to house framing, plumbing, wiring, etc.

2. Install a non-combustible hearth pad (where necessary).

3. Place the appliance 15” (37.5 cm) away from the wall. If the stove is to be set on a hearth pad,

set the unit on it.

4. Locate the center of the exhaust pipe on the stove. Extend that line to the wall. Once you have

located the center point on the wall, use a hole saw to cut a 7” (175 mm) diameter hole for a 3”

(76 mm) vent pipe or an 8” (200 mm) hole for a 4” (101 mm) vent pipe.

5. Install the wall thimble as per the instructions written on the thimble.

6. Install a length of 3” (76 mm) or 4” (101 mm) vent pipe into the wall thimble. The pipe should

install easily into the thimble.

HORIZONTAL EXHAUST THROUGH THE WALL:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Enviro Pelletofen Handbücher

Enviro

Enviro Omega Bedienungsanleitung

Enviro

Enviro M-55C-FS Bedienungsanleitung

Enviro

Enviro BERN C-10629 Bedienungsanleitung

Enviro

Enviro Bern Bedienungsanleitung

Enviro

Enviro Mini A Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro Empress Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro Milan Bedienungsanleitung

Enviro

Enviro Mini A Bedienungsanleitung

Enviro

Enviro Maxx-1 Bedienungsanleitung

Enviro

Enviro WINDSOR Bedienungsanleitung

Enviro

Enviro M55C-FPI Bedienungsanleitung

Enviro

Enviro Maxx-1 Bedienungsanleitung

Enviro

Enviro EF2 Bedienungsanleitung

Enviro

Enviro Empress Bedienungsanleitung

Enviro

Enviro P3 Bedienungsanleitung

Enviro

Enviro WINDSOR Bedienungsanleitung

Enviro

Enviro EF-IV I Bedienungsanleitung

Enviro

Enviro M55C-FPI Bedienungsanleitung

Enviro

Enviro EF-III BAY I FS Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro P3 Bedienungsanleitung

Enviro

Enviro P4 Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Quadra-Fire

Quadra-Fire 1000 Gold Betriebsanleitung

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung