Envirovent CLASSIC-100 Handbuch

CLASSIC-100

Instruction leaflet

CLASSIC-100

Instruction leaflet

CLASSIC-100

Instruction leaflet

CLASSIC-100 AXIAL EXTRACTOR FANS

Suitable for bathroom applications

Thank you for placing your confidence in EnviroVent by buying this product. It

has been manufactured in accordance with current technical safety regulations,

production and quality standards as laid down by the international Quality

Standard ISO 9001. Please read this instruction booklet carefully before installing

or operating the product. It contains important information on personal and user

safety measures to be followed whilst installing, using and carrying out

maintenance work on the equipment. Once the product has been installed, please

pass this booklet to the end user.

Check that the product is in perfect condition whilst unpacking. Any fault or

damage caused in origin is covered by the EnviroVent guarantee. Please make

sure that the product corresponds to the one you have ordered and that the

details on the instruction label fulfil your requirements.

IMPORTANT:

BE SURE TO HAVE READ AND UNDERSTOOD THESE INSTRUCTIONS BEFORE

BEGINNING THE INSTALLATION PROCESS

SAFETY AND RECOMMENDATIONS

All wiring must comply with Building Regulations and the current I.E.E. Wiring

Regulations (BS7671) or the equivalent standards for your country. The final

installation should be examined and tested by a competent person.

This fan is IP44 rated.

Do not install near sources of heat in excess of 40°C.

Position away from any source of water spray from a bath or shower. Do not site in

a shower enclosure.

Position the fan at the furthest distance from the main source of air replacement in

the room in order to achieve maximum airflow performance.

This appliance is not intended for use by young children or infirm persons unless

they have been adequately supervised by a responsible person to ensure that they

can use the appliance safely. Young children should be supervised to ensure that

they do not play with the appliance.

•

CLASSIC-100

Instruction leaflet

INSTALLATION: CLASSIC -100

Fig.1

Fig.3

Fig.2

Fig.4

123756

Fig.5

Fig.6

abc

Fig.8

Fig.7

CLASSIC-100 S

Fig.9

CLASSIC-100 T

CLASSIC-100 XT

Fig.11

Fig.12

CLASSIC-100 XP

CLASSIC-100 HP

CLASSIC-100 XHP

Fig.10

Fig.13

CLASSIC-100 XHT

Fig.14

Fig.15

CLASSIC-100 AXIAL EXTRACTOR FANS

Suitable for bathroom applications

INSTALLATION

IMPORTANT: before installing and wiring the unit, ensure that the mains supply is

disconnected.

CLASSIC-100 should only be used in conjunction with fixed wiring.

Fig.1 1 – Grille

2 – Cable entry point

3 – Connection cover

4 – Fixing screw

5 – Connection terminals

6 – Outlet

7 – Slot

The CLASSIC-100 is suitable for wall, ceiling or window (using the CLASSIC-100 window

kit) installations.

Panel Model

Drill a 105mm-diameter hole in chosen position in the panel surface.

Loosen the screw (4), which holds the grille in place (1) and remove grille.

Mark the fixing holes in the back of the fan plate. This fan must be installed by a

competent person. Complete electrical wiring of fan as outlined in the Wiring

Instructions overleaf. Then refit the grille and tighten the screw (4).

Bind the adhesive tape supplied around the outlet (6).

Wall Model

Drill a 115mm diameter hole in chosen position through the wall. Slope the wall

sleeve downwards to prevent rainwater running through the duct into the unit. The

end with the larger diameter should be on the room side.

Loosen the screw (4), which holds the grille in place (1) and remove grille.

Mark the 4 screw hole positions. Drill, plug and screw into position. Repeat this

process for the external grille sub-

frame. Fix the exterior grille in position, whilst

ensuring that the louvres are positioned downwards.

Check that the wall tube is not distorted and that the impeller turns freely.

This fan must be installed by a competent person. Complete electrical wiring of fan as

outlined in the Wiring Instructions below. Then refit the grille and tighten the screw (2).

Bind the adhesive tape supplied around the outlet (6).

•

Window Model (Fig. 5)

These models have been designed for installation on a window (single or double glazed)

using the CLASSIC 100 Window Fixing Kit.

Fig.5 1 & 10

– Protection grille

2 – Cable entry point

3 – Connection cover

4 – Fixing screw

5 – Connection terminals

6 – Outlet

7 – Rubber joints

8 – Spacers

9 – Threaded ring

Cut a 105mm -diameter hole in glass.

Loosen the screws on the front and back protections grilles (1 and 10). Loosen the

threaded ring (9) and remove the 4 spacers (8).

Mount the fan depending on the installation requirements so that the glass is between

the two rubber joints (7):

Fig. 6a: All the spacers on the outside

Fig. 6b: All the spacers on the inside

Fig. 6c: Spacers on the outside and the inside.

For double-glazing, one or more spacers may be discarded.

Fix the threaded ring. Fix the exterior grille in position, using the screws provided. This

fan must be installed by a competent person. Complete electrical wiring of fan as

outlined in the Wiring Instructions overleaf. Then refit the front grille and tighten the

screw (2).

WIRING INSTRUCTIONS

IMPORTANT: ENSURE THAT THE MAINS SUPPLY IS SWITCHED OFF BEFORE

MAKING ELECTRICAL CONNECTIONS.

The CLASSIC

-100 is designed for single-phase supply, suitable for connection to 220-

240V/1/50Hz supply. It is double insulated (Class II) and must not be earthed. The in-

stallation must include a double pole switch with a contact clearance of at least 3mm.

There are two options for cable entry to the fan. If using recessed wiring, the cable must

be introduced through the slot (7) (Fig. 1). If using surface wiring the cable must be intro-

duced as shown in Fig 3 and the break-out region on the left hand side of the front grille

should be removed.

For access to the fan terminals, remove the safety cover screws and hinge up (Fig. 4).

•

CLASSIC – 100 S

This model uses the following wiring diagrams:

Fig.7. Fan operating through a light switch.

Fig.8. Fan operating through an independent switch.

CLASSIC - 100 X Models (XP, XHP, XT)

Models fitted with thermo-electric automatic shutter.

WARNING: The opening of the shutter is facilitated by means of a thermal system

that requires a few seconds to open completely.

CLASSIC - 100 XP (Fig. 9)

Single speed fan, fitted with thermo-electric shutter and integral pullcord.

CLASSIC - 100 H Models (XHP, XHT, HP)

Provided with an integral humidity sensor, which can be adjusted from 60-90% RH by

the rotary switch on the front of the fan without removing the grille. The controller is

factory set to approx. 72% RH.

To lower the RH, turn the adjuster towards the minus sign. The fan will operate

more frequently, as the controller will be more sensitive.

To increase the RH, turn the adjuster towards the plus sign. The fan will operate

less frequently, as the controller will be less sensitive.

CLASSIC-100 HP (Fig. 10)

Automatic operation with pull cord switch enabling override of the fan when the relative

humidity level in the room is lower than the set % RH value.

CLASSIC –100 XHP (Fig. 10)

Fitted with thermo-electric shutter and pull cord switch enabling override of the fan when

the relative humidity level in the room is lower than the set % RH value.

CLASSIC - 100 T Models (T, XT)

The timer enables the fan to continue running for the selected period after the switch has

been turned off. The desired run-on time is selected by means of an adjuster “T” posi-

tioned on the printed circuit board (Fig.13).

CLASSIC –100T&XT

Fig.11. Fan operating through a light switch.

Fig.12. Fan operating through an independent switch.

CLASSIC –100 XHT

Fitted with thermo-electric shutter, humidity sensor and timer.

Fig. 14. Fan operating through a light switch

Fig. 15. Fan operating through an independent switch

•

CLEANING AND MAINTENANCE

IMPORTANT: DISCONNECT FROM THE MAINS SUPPLY BEFORE CARRYING

OUT CLEANING OR MAINTENANCE

To ensure optimum performance from your extract fan, it should be cleaned

periodically by a competent person.

AFTER SALES SERVICE

We recommend you do not dismantle or remove any other parts than those

mentioned, as any tampering would automatically cancel the guarantee. If you detect

any fault, contact EnviroVent on 01423 810810.

Remember, if you have any problems please call our dedicated Technical Team on

the Hotline 0845 27 27 810.

All EnviroVent products are designed to be recycled when they reach the end of their

working life. To save the environment and to reduce landfill, please call EnviroVent

on 0845 27 27 810 to arrange for the fan to be returned to the factory.

EnviroVent Ltd

EnviroVent House

Hornbeam Business Park

Harrogate

HG2 8PA

Thank you for choosing EnviroVent - the fastest growing ventilation company in the

UK.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Envirovent Lüfter Handbücher

Envirovent

Envirovent SILENT 100 Handbuch

Envirovent

Envirovent filterless extractor fan Bedienungsanleitung

Envirovent

Envirovent cyclone 7 Bedienungsanleitung

Envirovent

Envirovent SILENT Handbuch

Envirovent

Envirovent SLIMLINE 300 Kurzanleitung

Envirovent

Envirovent Silent-100 Design Handbuch

Envirovent

Envirovent energiSava 250 Bedienungsanleitung

Envirovent

Envirovent energiSava 200 Bedienungsanleitung

Envirovent

Envirovent OZEO Bedienungsanleitung

Envirovent

Envirovent Slimline 150 Kurzanleitung

Envirovent

Envirovent Damp Pro DP-EVL Bedienungsanleitung

Envirovent

Envirovent SILENT Handbuch

Envirovent

Envirovent VENTY ECO2 Air Kurzanleitung

Envirovent

Envirovent SILENT MV-160/100 Montageanleitung

Envirovent

Envirovent FILTERLESS EXTRACT FAN SELV Series Kurzanleitung

Envirovent

Envirovent energisava 380 Bedienungsanleitung

Envirovent

Envirovent Eco dMEV+ Bedienungsanleitung

Envirovent

Envirovent PIV Bedienungsanleitung

Envirovent

Envirovent POWER-170 Montageanleitung

Envirovent

Envirovent CYCLONE 7 230V Series Kurzanleitung

Envirovent

Envirovent energiSava 300 Bedienungsanleitung

Envirovent

Envirovent SABIK 350 Bedienungsanleitung

Envirovent

Envirovent ATMOS WALL Bedienungsanleitung

Envirovent

Envirovent SELV Kurzanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung