Epson LQ 1050 - B/W Dot-matrix Printer Abmessungen
EPSON AMERICA, INC.
EPSON
Product Support Bulletin
Subject:
24 Pin Printer Error and Beep Codes
Date: 4/3/91
PSB No: P-0076
Page(s): 1 of 4 Originator JV
Epson printers issue beep tones when certain error conditions exist. Those beeps
can assist you in locating and repairing customer’s printers. The following error
codes are listed by product name.
NOTE:
Most of the beeps issued by the printers are of .1 second duration with a .1
second pause between beeps. Where the beeps or the pauses are longer,
it has been noted in the text. The description “3 Beeps x 2” means two sets
of three beeps.
LQ-200/AP-3000
1 beep: BEL code
1 beep: A Control Panel setting is accepted.
3 beeps: Paper End detected
5 beeps: Abnormal carriage movement
On-Line light is flashing:
Printhead is over heated. Carriage will stop until
the printhead cools down.
LQ-500, LQ-510, LQ-1010, LQ-850, LQ-950, LQ-1050,
L1000, AP-4000, AP-4500
1 beep: BEL code (.5 sec beep)
1 beep: A Control Panel setting is accepted
3 beeps: Paper End detected
5 beeps: Abnormal carriage movement
PSB No: P-0076
Page: 2 of 4
LQ-800, LQ-1000, L750
1 beep: BEL code
1 beep: A Control Panel setting is accepted
3 beeps: Paper End detected
5 beeps:
Abnormal carriage movement
(.5 sec. pause between beeps)
5 beeps:
LQ-860
+35V supply is abnormal
1 beep: BEL code (.5 sec. beep)
1 beep:
A Control Panel setting is accepted
3 beeps: Paper End detected
5 beeps:
Color select mechanism error
(.5 sec. beep, .5 sec between beeps)
5 beeps:
Abnormal carriage movement
(.5 sec. beep, .5 sec between beeps)
5 beeps:
CG ROM failure
(.5 sec. beep, .5 sec between beeps)
LQ-1500
1 beep:
BEL code
5 beeps: Paper End detected
5 beeps: Abnormal carriage movement
(.5 sec. pause between beeps)
PSB No: P-0076
Page: 3 of
4
LQ-2500
NOTE:
Printers with LCD displays use error messages along with beeps to
inform the user of problems. The following messages will help you to
troubleshoot problems.
A blank LCD screen with the Power-on LED lit can be caused by a bent
pin on one of the PROM
S
or jumper J1 may be set incorrectly.
1 beep: BEL code
5 beeps: Abnormal voltage-
5 beeps: Abnormal carriage movement
(.5 sec. pause between beeps)
LQ-2500 LCD Codes:
00 Invalid ID request to CGROM
03
EEROM read/write error
10
LQ-2550
Abnormal carriage movement
1 beep: BEL code
3 beeps:
Paper End detected
5 beeps: Abnormal carriage movement (.5 sec. pause between
beeps)
5 beeps: Platen Gap adjustment error (.5 sec. pause between
beeps)
5 beeps: Case open
LQ-2550 LCD Codes:
00 (1)
The font could not be found. The printer’s internal program could not
find the target font.
(2)
Missing or damaged 7A ROM
02
Internal ROM check does not match. The versions may have been mixed.
PSB No: P-0076
Page:
4
of
4
LQ-2550 cont.
03
10
11
12
20
A ‘Verify After Write” check to the SRAM has failed. The SRAM could be bad.
This is a motor control error. Four possible areas of failure are:
a. CR home condition not detected at power up
b. Platen gap motor HP not detected correctly
c. Friction/Tractor feed switching error
d. Physical obstruction such as a jammed ribbon
Skewed paper detect error. Since the initial reading upon loading a single
sheet paper, the paper has skewed. This is a printhead wire protection
feature.
Illegal paper positioning.
(1)
If the paper is loaded using the knob instead of the LOAD/EJECT switch,
this error condition will occur. This is a printhead wire protection feature.
(2)
PE sensor may have failed or is not connected.
CPU error. An undefined op-code was detected.
NOTES:
Error codes 11 and 12 are usually caused by new operators who are
un-familiar with the machine. Both of these errors are corrected by
turning the printer off, taking out the paper and turning the printer back
on. Both features were added to ensure proper paper handling and
prevent paper jams, which can result in printhead failures.
Incorrect jumper settings on the ROMA board may cause errors 10 or
20. The correct settings are documented in the Service Manual (page
A-54, figure A-52) and on TIB LQ2550-005.
Errors 0,2, 3, 10, and 20 may require a repair, adjustment or
replacement.
Product Support Bulletin
Subject:
Power Specifications
Date: 2/7/90 PSB No: P-0060
Page: 1 of 2 Originator: RFB
The following information is a list of the power requirements for
the Epson 9 and 24 pin printers and laser printers.
504
VA maximum
PSB No: P-0060
Page: 2 of 2
Product
1
Voltage
1
Max.
Current
Consumption
1
Power
Consumption
1
BTU/HR
LX810
1
12ov
.7
Amp 84
VA
maximum
I
286.69
T750 120v 1.0
Amp
120
VA
maximum
409.56
TlOOO
120v
.7
Amp 84 VA
maximum
286.69
If the power requirements of a particular Epson printer is not listed please
refer to the appropriate User's Manual for the electrical specifications.
In the event that the User's Manual is not available, locate the silver label
on the back of the Epson printer.
This is a reliable source for the electrical
requirements.
The following formula is used to calculate the electrical
power requirements:
VOLTAMPS is equivalent to WATTS
VOLTAMPS = Volts * Amps
AMPS
BTU/HR
= Voltamps/Volts
= Watts * 3.413
Example:
120V
*
1A =
120VA
120VA/120V
=
1A
120VA
is
equivalent
to
120W
120W
*
3.413
=
409.56
BTU/HR
Heat
output
is
rated
in
BTU/HR.
EPSON
EPSON AMERICA, INC.
INFORMA
Product Support Bulletin
Subject:
Tractor Pin Alignment
Date: 5/15/89
PSB No: P - 0044
Page: 1 of 1
Originator: RP
bd
The purpose of this bulletin is to insure the proper installation and alignment of
the FX- 850/1050 and LQ- 850/1050 push tractor assemblies.
There are two possible ways to install the tractor frame on the push tractor
assembly. If the frame is installed incorrectly, the tractor belt pins on the two
tractors will not be aligned, and the resulting printout appears to be slanted on
the page, or the perforated edge will be tom. This is caused by the marks on
the tractor shaft holders being 180 degrees ‘out of phase.’
When assembling a tractor, there are two grooves in the shaft, and two tabs
on the tractor shaft holder. lf the pins on both tractor belts are not aligned, it
will be necessary to disassemble the tractor, and rotate one tractor shaft holder
180 degrees, to bring it back into alignment with the other shaft holder.
Alignment can be verified by examining the marks in the shaft holders, which
will both be in the forward position when properly aligned, as shown in
Figure
4- 51 below.
Figure 4-51. Tractor Assembly
Phases
PRODUCT SUPPORT BULLETIN
PSB NO.: P-0035
DATE: 11/29/88 PAGE: 1 of 3
SUBJECT: LQ-850/950/1050 PRINTER QUESTIONS
Q:
How do I get the short tear off feature to work?
A:
The first step is to turn the dip switch 2-7 to the "ON"
position.
Then there are two ways to activate the short
tear off.
The first way is to send a form feed at the end
of each page.
The second way is to send 66 lines of data
to the printer.
In both instances data transmission must
stop for a minimum of 3 seconds before the feature is acti-
vated.
Q:
When printing on single sheets,
lines.
each page drops down several
Why?
A:
The number of printable lines on single sheets are 61 or 62.
Change the number of lines/page in your software package.
Q:
Where are the P-ROM and Character Generator ROM located on
the main board of the LQ-850/950/1050?
A:
The P-ROM is in location 9A. The Character Generator ROM
is in location 6A.
Q:
What size buffer does the LQ-850/950/1050 have?
A:
6K bytes or OK bytes. This is selectable by dip switch 1-8.
Q:
What are the printing speeds?
A:
The printing speeds are:
Pitch Quality Characters/Second
10
Draft
220
10
LQ
73
12
Draft
264
12
LQ
88
Q:
What ribbons does the LQ-850/950/1050 take?
A:
Printer Standard Ribbon Film Ribbon
LQ-850 #7753 #7768
LQ-950 #7767
#7769
LQ-1050
#7754 #7770
Q:
Does the LQ-850/950/1050 support color?
A: No.
EPSON AMERICA SERVICE, 23610 TELO AVENUE, TORRANCE, CALIF. 90505
NUMBER: P-0035 PAGE: 2 of 3
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
What fonts are built into the LQ-850/950/1050?
Draft
Roman(10cpi, 12cpi, 15cpi)
Roman Proportional
Sans Serif(10cpi, 12cpi, 15cpi)
Sans Serif Proportional
Are there any optional fonts available?
Courier(10cpi, 12cpi, 15cpi) :
Font Module #7400A
Prestige(10cpi, 12cpi, 15cpi) : Font Module #7401A
Script(10cpi, 12cpi, 15cpi) :
Font Module #7402A
OCRB(10cpi)
:
Font Module #7403A
Orator(10cpi)
:
Only Available with #7407
Orator-S(10cpi)
:
Only Available with #7407
Multi-Font Module*
:
Font Module #7407
*
Multi-Font Module contains all the above listed fonts.
It is available for the LQ-950 and LQ-850/1050 with the
upgrade (LQ850/1050U).
What type of paper feeds do they support?
Friction
Built-in push feed tractor with paper tension unit.
Single bin or dual bin Cut Sheet Feeder (optional)
Pull Tractor (optional)
What size envelopes can they print on?
Number 6 and number 10 envelopes.
What are the paper thickness specifications for multi-
part forms?
It will print on continuous multi-part carbonless forms,
with one original and up to 3 copies. The maximum paper
thickness should not exceed 0.0126 inches.
If it comes with the built-in push feed tractor unit,
why does it need an optional pull tractor?
When printing on multi-part forms, the optional pull
tractor keeps the forms taut for more consistant
paper feeding.
How do I switch from parallel to serial in the printers?
The dip switches on the back of the printer determine
which interface is being used.
NUMBER: P-0035
PAGE:
3 of 3
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
What if I want to install an optional serial interface
board?
Install the optional interface as detailed in the User's
Manual.
Then set the dip switches on the printer to the
parallel position and then set the dip switches on the
optional interface board to enable it.
Which optional serial interface boards will work?
The two current serial interface boards that work are the
8143 and the 8148.
If I want to use the built-in serial interface on the
printer,
what cable do I use?
Epson markets two cables that allow direct connection to
personal computers. When connecting the 6 pin DIN to an
IBM PC/XT or compatible DB-25 serial port use cable #8297.
When connecting to an IBM AT or compatible 9 pin serial port
use cable #CA-070.
Does the LQ-850/950/1050 support the legal character set?
The LQ-950 does have the legal character set built in.
The
LQ-850/1050 needs the upgrade kit (kit #LQ850/1050U) to
support the legal characters.
What is the upgrade kit for the LQ-850/1050?
The upgrade kit, #LQ850/1050U, upgrades the printer to allow
the use of the new dual bin cut sheet feeder (product code
for the LQ-850 = #7346 and for the LQ-1050 = #7348).
What does the upgrade kit contain?
It has a new P-ROM, instruction sheet, an errata sheet and
a new user's manual.
Is the upgrade kit for the LQ-950 too?
No, the LQ-950 comes standard with the upgrade built in.
Andere Handbücher für LQ 1050 - B/W Dot-matrix Printer
1
Dieses Handbuch passt für folgende Modelle
16
Inhaltsverzeichnis
Andere Epson Drucker Handbücher
Epson
Epson J7100 - TM Two-color Inkjet Printer Bedienungsanleitung
Epson
Epson TM-H6000III Series Bedienungsanleitung
Epson
Epson WorkForce WF-M1030 Bedienungsanleitung
Epson
Epson L3100 Series Bedienungsanleitung
Epson
Epson LQ-590 Bedienungsanleitung
Epson
Epson PictureMate Show - PM 300 - PictureMate Show Digital... Bedienungsanleitung
Epson
Epson Expression Premium XP-800 Montageanleitung
Epson
Epson Stylus Photo PX700FW Bedienungsanleitung
Epson
Epson FX-1180 - Impact Printer Bedienungsanleitung
Epson
Epson STYLUS S20 Series Bedienungsanleitung
Epson
Epson M316A Bedienungsanleitung
Epson
Epson Stylus Pro 10000 Series Bedienungsanleitung
Epson
Epson 500DN - B Color Inkjet Printer Bedienungsanleitung
Epson
Epson Stylus Pro Series Installations- und Betriebshandbuch
Epson
Epson L6490 Series Bedienungsanleitung
Epson
Epson PictureMate Handbuch
Epson
Epson Stylus C40UX Bedienungsanleitung
Epson
Epson LQ-680 Bedienungsanleitung
Epson
Epson WorkForce ST-C8000 Bedienungsanleitung
Epson
Epson LQ-1070+ Bedienungsanleitung
