Epson PowerLite 900 Bedienungsanleitung

MIS Continuous Flow for Epson Photo 900

Installation Instructions

What you will need to Install the Photo 900 CFS

• Complete CFS-900P Kit

• Scissors

• Measuring Tape or Ruler

• Marking Pen or Pencil

• Paper Towels

• Alcohol or Cleaning Solution

What is included in your Photo 900 CFS Kit

• Cartridge Set with tubes attached

• Set of 6 Inks (C, Lc, M, Lm, Y, K)

• 6 Drilled Bottle Caps

• Clear Plastic Bridge Bracket with Black Velcro

• Clear Plastic Tube Support with White Adhesive Backing

• 1 Beige Tube Clip

• 6 Black Velcro Circles (Hook & Loop)

• 1 Piece of Loop Velcro ¾ x ¾

• 2 thin tie wraps.

Step 1 - Check Printer Condition

If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson

cartridges that came with the printer. Follow normal installation instructions for the software. Test the

printer by printing pictures. Learn how to use the Epson utilities to run a Nozzle pattern check and to run

a Cleaning Cycle.

Make sure that the printer can produce a perfect nozzle pattern before

proceeding with Permaflow installation.

If you have been using the printer in the past, just make sure it produces a perfect nozzle pattern before

proceeding with the Permaflow installation. If the Nozzle pattern has any gaps whatsoever, then run

cleaning cycles until it prints perfectly.

Step 2 – Disconnect Power From Printer

Push, but do not hold the INK button on the printer. This will move the cartridges to the “replacement”

position. After they move to this position, which is on the left, PULL THE POWER PLUG OUT OF THE

WALL. Now the cartridges can be moved from side to side by hand. We will tell you later when to

reattach the printer power plug (step 9).

Step 3 – Install Tube Supports

Use your alcohol or cleaning solution and clean the top of the printer housing where the clear plastic Tube

Support is going to attach. Make sure you wipe this area clean and dry before proceeding. See photo

below. (The Tube Support is the clear plastic piece with the white foam tape on it.)

Use a pencil or marking pen, and mark a line on the printer housing, at 3 1/8 inches from the edge of the

printer housing as shown in the above photo. This photo was taken after the tubes were installed.

Next, you will notice that the Bridge Bracket has both the Hook and Loop Velcro on it. The Hook portion

of the Velcro is going to end up attached to your printer. The Loop portion will remain on the Bridge

Bracket. Do not separate the Hook and Loop, Keep them together just like they were when delivered.

Remove the adhesive backing from the Hook portion of the Velcro. Keep it attached to the Loop portion.

Carefully install the Bridge Bracket in its proper location at the left edge of the housing, as shown above.

Keep it straight and press down firmly all along the edges. When you lift up the Bridge Bracket, after

pressing it down, the Hook Velcro will remain in place on the printer.

Keep the Bridge Bracket off for now.

Step 4 - Install Protective Velcro

In the kit there is a small piece of Velcro ¾ x ¾ . Install it on the left edge of the printer in the position

shown below

Step 5 – Prepare Cartridges

Prefilled Carts

On the end of the cartridge tubes, there is a black steel paper clip. Remove this clip and unfold the tubes

so they lay flat. The black paper clip is no longer needed, it was just for shipping purposes. The ends of

the tubes should be split so they can be separated easily. Don’t separate them now.

Empty Carts

The ends of the tubes should be split so they can be separated easily. Separate them back about 6

inches, no more.

If you ordered an empty cartridge set, you must put ink in it before it can be used. There are two ways to

put ink into the carts. Fill from bottom with syringe and bottom fill adapter, or use a vacuum pump. If you

fill from the bottom, then inject ink into the bottom of the cartridge until you just begin to see in at the top

of the cartridge. If you are vacuum filling, follow the instructions that came with the vacuum pump.

Make sure you get the right inks in the right cartridge chambers. The cartridges are marked on top.

After filling the empty cartridges, let them sit on your bench in their installed position for at least 2 hours,

so that any trapped air can rise to the top.

Step 6 – Install Cartridges

Use a flat blade screwdriver and remove the Epson cartridge hold down clamps, black and color. Insert

the screwdriver blade at the hinge point and twist. The clamps will come right off, without any damage.

Keep these in a safe place, you may need them in the future.

Remove the original Epson cartridges from the printer (power is disconnected). Set them aside on some

paper towel. Do not throw away, you may need them someday. Wrap in a zip-lock plastic bag for safe

keeping.

Put the MIS CFS cartridges into the printer. Carefully align them and make sure they go down all the

way. They should fit tight. Once you put them in and they are down all the way, DO NOT LIFT UP

AGAIN.

Push the cartridges to the far right side of the printer. Put some alcohol on the tubes so they will fit into

the Tube Support Bracket. Adjust the tubing so that all excess slack is taken up, but not to the point that

it starts to pull the cartridges away from the far right hand position.

After the tubing is in place in the Tube Support Bracket, move the carts by hand from left to right. You

should be able to get to the far right and far left positions without any restrictions.

Re-install the clear plastic bridge bracket and try moving the carts back an forth again. It should be

smooth and the tubes should not touch the bottom of the printer. They will make contact with the Bridge

Bracket and the printer housing, but there is Velcro there to prevent any damage to the tubes.

For extra security, you can install the tie wraps to hold the cartridges in place. Long term this is a good

way to prevent the carts from rising up and giving you red light problems.

Step 7 – Finish Tubing Installation

Move the ends of the tubes to the right side of the printer so theyextend over the end of the printer. Clean

the right end of the housing with alcohol. Install the beige tube clip in a position so the tubes come

straight off, not at an angle. See photo below.

Insert the tubing into the tube clip and close it until it snaps shut. Don’t pinch any of the tubes.

Next, separate the tubes, or un-web them, so that they are separated all the way back to the beige tube

clip you just installed.

Now you are ready for the ink bottles.

Step 8 – Set up the Ink Bottles

Find the ink bottles and the black Velcro Circles. Clean the back of each bottle with alcohol and wipe dry.

Attach a Velcro Loop circle to the back of each bottle. Attach the mating Velcro circle to the piece on the

bottle. Peal off the backing on the mating Velcro so the adhesive is exposed.

Take off the shipping caps and install the drilled caps. Each cap should have a hole in the center and a

small vent hole in the Nalgene logo. Make sure the vent hole is there and that it is not blocked or

obstructed.

Arrange the bottles as shown above. From front to back they should be in this order…..

Yellow – Light Magenta – Magenta – Light Cyan – Cyan – Black

When you press the exposed Velcro adhesive against the printer, the hook portion will stick to the printer

and this becomes the permanent position for the bottle, so choose your bottle positions carefully.

Velcro attaches bottles to printer

(This is photo from a 2200 printer)

Hold the tube against the outside of the ink bottle. Cut off the excess tube at a 45 degree angle. Insert

the tube into the bottle. Make sure that you insert 3 ½ to 4 inches of tube length into the center hole in

the bottle cap. This will put the end of the tube on the bottom of the bottle. Put a little alcohol on the

tube so it slips through the center hole in the bottle cap.

Make sure the correct color tube goes into the correct color

ink bottle. A mistake here will ruin the whole s

stem.

The tubes should make a nice smooth curve into the bottles. It should look like the photo above.

The fully installed system should now look like the photo below, except the tubes will be empty and the

power is still off.

Step 9 – Testing the System

Push the cartridges to the far right and reattach the printer power. Turn on the power on the front of the

printer if needed. Have you computer and graphics program up an ready to go.

The printer should come on and move back an forth a few times and do a cleaning cycle. When it stops

moving, only the green light should be on.

A red light at this point is not a good thing. It indicates the one of the cartridges is not seated all the way

down. Go back to Step 6 and make sure that all the cartridges have seated properly. Lift them just

slightly, if needed and reseat them.

After the cleaning cycle is over, bring up an image on your favorite graphics program and get set to make

a print. Be sure to put paper in the printer. Before printing, use the printer properties and Epson utilities

to check the nozzles. The nozzle pattern may not be perfect at this point.

Run 3 or 4 cleaning cycles if necessary to achieve a perfect nozzle pattern. When all the nozzles are

present, make a print. You should now see ink coming up the tubes. As long as the print is satisfactory

and all the nozzles are present, there is no need to do any further cleaning cycles.

Don’t worry about the inks, it will take several (20 or more) prints for the inks to reach the cartridge. There

is no particular order in which they will get there.

Maintenance Suggestions

• Try to make a print every day to keep the system fresh. These systems do not like to be left for

days at time without printing.

• Don’t let your ink levels get below 1/4 empty. Add additional ink when this happens. The tube

can be lifted out of the ink to add more. Don’t leave the tube out of the ink for a long period of

time. The cartridge can drip ink into the printer when the tube is out, but it happens slowly.

• Once you have installed the cartridges, do not lift them up. Lifting up the cartridges lets air into

the ink inside the cartridge and it can become foamy. Foamy ink will not print.

• After you do cleaning cycles or after the printer has been off and then turned back on, the Auto

Reset chips on the cartridges will reset themselves to full. When this happens, you have to

acknowledge a message from Epson indicating that the chips are not authentic Epson chips.

Just click the YES button to continue.

• If you get a red light when printing. Shut the printer off, cancel your print job and wait 10

seconds. Then turn the printer power back on, the Auto Reset chips will reset themselves back

to full and you can continue printing.

For additional technical assistance, visit the MIS website troubleshooting guide ….

http://www.inksupply.com/index.cfm?source=html/cobratrouble.html

Andere Handbücher für PowerLite 900

Inhaltsverzeichnis

Andere Epson Drucker Handbücher

Epson

Epson PM-520 series Bedienungsanleitung

Epson

Epson ET-L6550 Series Bedienungsanleitung

Epson

Epson Stylus Color 880 Bedienungsanleitung

Epson

Epson L380 Bedienungsanleitung

Epson

Epson ProofPlus TM-H6000III Bedienungsanleitung

Epson

Epson SureColor P-Series Bedienungsanleitung

Epson

Epson SureColor T5475 Bedienungsanleitung

Epson

Epson XP-432 Series Bedienungsanleitung

Epson

Epson R260 - Stylus Photo Color Inkjet Printer Handbuch

Epson

Epson TM-T88V Gebrauchs- und Pflegehandbuch

Epson

Epson Stylus Photo R290 Bedienungsanleitung

Epson

Epson Stylus Pro 5500 Bedienungsanleitung

Epson

Epson Stylus Photo 1390 Bedienungsanleitung

Epson

Epson M100 Bedienungsanleitung

Epson

Epson WF-2010 Bedienungsanleitung

Epson

Epson Stylus Photo 890 Bedienungsanleitung

Epson

Epson C31C514452 Gebrauchs- und Pflegehandbuch

Epson

Epson LQ-1500 Bedienungsanleitung

Epson

Epson U675 - TM Color Dot-matrix Printer Bedienungsanleitung

Epson

Epson Stylus Photo PX730WD Montageanleitung

Epson

Epson EP-4004 Betriebsanleitung

Epson

Epson Stylus Color 640 Bedienungsanleitung

Epson

Epson Stylus Pro 7000 Series Bedienungsanleitung

Epson

Epson SC-T3000 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung