Epson TM-T70 Bedienungsanleitung

English

User’s Manual. . . . . . . . . . . . . . . . . . . . 1

Benutzerhandbuch . . . . . . . . . . . . . . . . . 7

Gebruikershandleiding . . . . . . . . . . . . . 13

Manuel de l’utilisateur . . . . . . . . . . . . . . 19

Manual do utilizador . . . . . . . . . . . . . . . 25

Manual del usuario. . . . . . . . . . . . . . . . 31

Manuale dell’utente . . . . . . . . . . . . . . . 37

Руководство по эксплуатации . . . . . . . . 43

410464103

English

iii

English

FGH

DSW1

DSW2

English

DIP Switch Tables

*: When DIP Switches 1-7 and 1-8 are on, the transmission

speed can be selected from one of seven speeds:

2400, 4800, 9600, 19200, 38400, 57600, and 115200 bps

by control commands.

Serial Interface (DIP switch 1)

SW Function ON OFF

1-1 Data reception error Ignored Prints “?”

1-2 Receives buffer

capacity

45 bytes 4KB

1-3 Handshaking XON/XOFF DTR/DSR

1-4 Data word length 7 bits 8 bits

1-5 Parity check Enabled Disabled

1-6 Parity selection Even Odd

1-7

1-8

Selects transmission speed. (See table below.)

Transmission speed

Transmission speed (bps)-bits per second 1-7 1-8

Adjustable by control commands *ON ON

4800 OFF ON

9600 ON OFF

19200 OFF OFF

Serial Interface (DIP switch 2)

SW Function ON OFF

2-1 Handshaking

(BUSY condition)

Receive

buffer full

Offline or

Receive

buffer full

2-2 Reserved (Do not

change)

– Fix to OFF

2-3

2-4

Selects print density/

Low power comsumption

mode

See Table A.

2-5 [When TM-T88IV-

compatible mode is

enabled]

Setting the conditions

that cancels the receive

buffer BUSY state (This

function is effective when

the receive buffer

capacity is set to 4KB.

Cancels the

BUSY state

when the

remaining

capacity of

the receive

buffer

reaches 138

bytes.

Cancels the

BUSY state

when the

remaining

capacity of

the receive

buffer

reaches 256

bytes.

[When TM-T88IV-

compatible mode is

disabled]

Reserved

––

2-6 Reserved (Do not

change)

– Fix to OFF

2-7 I/F pin 6 reset signal Enabled Disabled

2-8 I/F pin 25 reset signal Enabled Disabled

Interface other than Serial (DIP switch 1)

SW Function ON OFF

1-1 Auto line feed Always

enabled

Always

disabled

1-2 Receives buffer

capacity

45 bytes 4 KB

1-3 [When TM-T88IV-

compatible mode is

enabled]

Selects paper sensor

to output paper-end

signal

Disabled Roll paper end

sensor enabled

Roll paper

near-end

sensor enabled

[When TM-T88IV-

compatible mode is

disabled]

Reserved

––

1-4 Error signal output Disabled Enabled

1-5~

1-8

Reserved – –

Interface other than Serial (DIP switch 2)

SW Function ON OFF

2-1 Handshaking

(BUSY condition)

Receives

buffer full

Offline or

receives

buffer full

2-2 Reserved (Do not

change)

– Fixed to OFF

2-3

2-4

Selects print density/

Low power

comsumption mode

See Table A.

2-5 [When TM-T88IV-

compatible mode is

enabled]

Setting the conditions

that cancels the receive

buffer BUSY state (This

function is effective

when the receive buffer

capacity is set to 4KB.

Cancels the

BUSY state

when the

remaining

capacity of

the receive

buffer

reaches 138

bytes.

Cancels the

BUSY state

when the

remaining

capacity of

the receive

buffer

reaches 256

bytes.

[When TM-T88IV-

compatible mode is

disabled]

Reserved

––

2-6

2-7

Reserved (Do not

change)

– Fixed to OFF

2-8 I/F pin 31 reset

(Do not change)

Fixed to ON –

Table A

Print density/low power SW 3 SW 4

Print density (Standard) OFF OFF

58 mm paper width model:

Print density (Standard)

80 mm paper width model:

Low power consumption mode

ON ON

Print density (Darker than standard) ON OFF

Print density (Dark) OFF ON

English

Specifications

80 mm paper width model 58 mm paper width model

Printing method Thermal line printing

Dot density 180 dpi × 180 dpi 203 dpi × 203 dpi

Printing direction Unidirectional with friction feed

Printing width 72.2 mm {2.84"}, 512 dot positions 52 mm {2.05"}, 416 dot positions

Characters per line

(default)

Font A: 42, Font B: 56 Font A: 34, Font B: 46

Character spacing

(default)

Font A: 0.28 mm {.01"} (2 dots)

Font B: 0.28 mm {.01"} (2 dots)

Font A: 0.25 mm {.01"} (2 dots)

Font B: 0.25 mm {.01"} (2 dots)

Character structure Font A: 12 × 24, Font B: 9 × 17

Font A is the default.

Character size

(Standard/Double-

height/Double-width/

Double-width and

Double-height)

Font A: 1.69 × 3.38/1.69 × 6.77/

3.38 × 3.38/3.38 × 6.77 mm

Font B: 1.27 × 2.40/1.27 × 4.79/

2.54 × 2.40/2.54 × 4.79 mm

Font A: 1.50 × 3.00/1.50 × 6.00/

3.00 × 3.00/3.00 × 6.00 mm

Font B: 1.13 × 2.13/1.13 × 4.25/

2.25 × 2.13/2.25 × 4.25

Number of characters Alphanumeric characters: 95; International characters: 48

Extended graphics: 128 × 11 pages (including user-defined page)

Print speed High-speed mode:

170 mm/s {6.69"/s} max. (4.23 mm

{1/6"} feed)

Ladder bar code and 2D code

printing: 100 mm/s {3.9"/s}

Low-power consumption mode:

150 mm/s {5.91"/s} max. (4.23 mm

feed {1/6"})

Bit image, Ladder bar code, 2D

code and Page mode: 60mm/s

{2.4"/s}

200 mm/s {7.87"/s} max. (4.23 mm {1/

6"} feed)

Ladder bar code and 2D code

printing: 100 mm/s {3.9"/s}

The above speed values are approximate.

The values are when the printer prints with the default print density level at

24 V and 25°C {77°F}. However, the print speed for the low power

consumption mode (for 80mm paper width models) is the value when the

printer prints at 34°C {93.2°F}.

Speed is adjusted automatically depending on the voltage applied and

head temperature.

Paper feed speed Approx. 170 mm/s {approx. 6.69"/s}

continuous paper feed

Approx. 200 mm/s {approx. 6.69"/s}

continuous paper feed

Line spacing (default) 4.23 mm {1/6"} 3.75 mm {30/203"}

Roll Paper (single-ply) Size: 79.5 mm ± 0.5 mm {3.13" ± 0.02"} Size: 57.5 mm ± 0.5 mm {2.26" ± 0.02"}

Maximum outside diameter: 83 mm {3.27"}

Roll Paper spool diameter: Inside: 12 mm {0.47"}; Outside: 18 mm {0.71"}

Thermal paper type Specified: NTP080-80 Specified: NTP058-80

Interface(compatible) Serial (RS-232/RS-485)/Parallel (IEEE1284)/USB/EPSON UB series

Receive buffer 4KB/45 bytes

Cash drawer function 2 drives

Supplied voltage*DC+24 V ± 7%

English

*: Be sure to use a safety-standards-applied power source that meets the following specifications.

Rated output: 24 V/2.0 A or more, Maximum output: 240 VA or less

dpi: dots per 25.4 mm (dots per inch)

Standards and Approvals

The following standards are applied only to the printers that are so labeled. (EMC is tested using the

Epson power supplies.)

Europe: CE marking

North America: FCC/ICES-003 Class A

Oceania: AS/NZS CISPR22 Class A

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

The connection of a non-shielded printer interface cable to this printer will invalidate the EMC standards

of this device.

You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation

could void your authority to operate the equipment.

CE Marking

The printer conforms to the following Directives and Norms:

Directive 2004/108/EC EN 55022 Class A

EN 55024

IEC 61000-4-2 IEC 61000-4-5

IEC 61000-4-3 IEC 61000-4-6

IEC 61000-4-4 IEC 61000-4-11

FCC Compliance Statement For American Users

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the

user will be required to correct the interference at his own expense.

For Canadian Users

This Class A digital apparatus complies with Canadian ICES-003.

À l'intention des utilisateurs canadiens

Cet appareil numérique de classe A est conforme à la norme canadienne NMB-003.

Current consumption

(at 24V)

High-speed mode:

Mean: Approx. 1.8 A

Low-power consumption mode:

Mean: Approx. 1.2 A

Mean: Approx. 1.4 A

Life Mechanism: 15,000,000 lines

Thermal head: 100 million pulses, 100 km

Autocutter: 1,500,000 cuts

Temperature Operating: 5 to 45°C {41 to 113°F}

Storage: –10 to 50°C {14 to 122°F}, except for paper

Humidity Operating: 10 to 90% RH

Storage: 10 to 90% RH, except for paper

Overall dimensions 114 × 125 × 194 mm {4.49 × 4.92 × 7.64"} (H × W × D)

Weight (mass) Approx. 1.8 kg {3.96 lb} (Roll paper exclosed)

80 mm paper width model 58 mm paper width model

TM-T70 User’s Manual 1

English

User’s Manual

DIP Switch Tables and Specifications

The DIP switch tables and technical specifications are at the beginning of this manual.

Illustrations

All of the illustrations are at the beginning of this manual. They are identified by letters (A, B, C . . .). Some

of the illustrations have numbers in them. See the list below for the meaning of the numbers.

transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with

respect to the use of the information contained herein. While every precaution has been taken in the

preparation of this book, Seiko Epson Corporation assumes no responsibility for errors or omissions.

Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third

parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of:

accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this

product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and

maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any

options or any consumable products other than those designated as Original Epson Products or Epson

Approved Products by Seiko Epson Corporation.

EPSON is a registered trademark of Seiko Epson Corporation in Japan and other countries/regions.

NOTICE: The contents of this manual are subject to change without notice.

Illustration AIllustration H

1. Thermal head 7. Paper guides

2. Autocutter blade

Illustration BIllustration K

3. Cover open lever 8. Thermal head

4. Printer cover

5. Power switch

6. Control panel

2TM-T70 User’s Manual

English

Important Safety Information

This section presents important information intended to ensure safe and effective

use of this product. Read this section carefully and store it in an accessible location.

Key to Symbols

The symbols in this manual are identified by their level of importance, as defined

below. Read the following carefully before handling the product.

WARNING:

Warnings must be observed carefully to avoid serious bodily injury.

CAUTION:

Cautions must be observed to avoid minor injury to yourself, damage to your

equipment, or loss of data.

Safety Precautions

This section describes the warnings and cautions intended to ensure safe and

effective use of the TM-T70. Other warnings and cautions on handling of this

product for its safe and effective use are described in other sections of the manual.

WARNING:

If the TM-T70 produces smoke, a strange odor, or unusual noise, shut down the

TM-T70, unplug the power cable immediately, and then contact your dealer or

an Epson service center for advice. Continued use may lead to fire or electric

shock.

Never attempt to repair this product yourself. Improper repair work can be

dangerous.

Never disassemble or modify this product. Tampering with this product may

result in injury or fire.

Be sure to use the specified power source. Connection to an improper power

source may cause fire.

Do not allow foreign matter to fall into the equipment. Penetration by foreign

objects may lead to fire.

If water or other liquid spills into this equipment, shut down the TM-T70, unplug

the power cable of the TM-T70 immediately, and then contact your dealer or

an Epson service center for advice. Continued use may lead to fire or shock.

If you open the DIP switch cover, be sure to close the cover and tighten the

screw after adjusting the DIP switch. Using this product with the cover open

may cause fire or electric shock.

Do not use aerosol sprayers containing flammable gas inside or around this

product. Doing so may cause fire.

CAUTION:

Do not connect cables in ways other than those mentioned in this manual.

Different connections may cause equipment damage or fire.

Be sure to set this equipment on a firm, stable, horizontal surface. The product

may break or cause injury if it falls.

Do not use this product in locations subject to high humidity or dust levels.

Excessive humidity and dust may cause equipment damage or fire.

TM-T70 User’s Manual 3

English

Do not place heavy objects on top of this product. Never stand or lean on this

product. Equipment may fall or collapse, causing breakage and possible injury.

Take care not to injure your fingers on the manual cutter

• When you remove printed paper

• When you perform other operations such as loading/replacing roll

paper

To ensure safety, unplug this product before leaving it unused for an extended

period.

Before moving this product, be sure to unplug it and all the cables connected

to it.

Caution Labels

The caution labels on the product indicate the following precautions.

CAUTION:

The thermal head can be very hot during printing and immediately after

printing. Touching it may cause burns. Be sure to do cleaning and other work

after the thermal head cools down. Also, be careful of the autocutter blade

near the thermal head. See illustration Afor the location of the thermal head

and the autocutter blade.

Restriction of Use

When this product is used for applications requiring high reliability/safety, such

as transportation devices related to aviation, rail, marine, automotive, etc.;

disaster prevention devices; various safety devices, etc.; or functional/precision

devices, etc.; you should use this product only after giving consideration to

including fail-safes and redundancies into your design to maintain safety and

total system reliability. Because this product was not intended for use in

applications requiring extremely high reliability/safety, such as aerospace

equipment, main communication equipment, nuclear power control equipment,

or medical equipment related to direct medical care, etc., please make your own

judgment on this product’s suitability after a full evaluation.

Purpose of This Manual

This manual provides information to operators of the TM-T70 printer to describe

basic operations to enable safe and correct use of the printer.

Part Names

See illustration B.

Unpacking

The following items are included with the standard specification printer. If any

item is damaged, contact your dealer.

❏Printer ❑Roll Paper

❏Power switch cover ❑AC adapter *

❏User’s Manual (this manual)

* May not be included with your printer.

4TM-T70 User’s Manual

English

Downloading Drivers, Utilities, and Manuals

Drivers, utilities, and manuals can be downloaded from one of the following

URLs.

For customers in North America, go to the following web site:

http://www.epsonexpert.com/ and follow the on-screen instructions.

For customers in other countries, go to the following web site:

http://www.epson-pos.com/

Control Panel

FEED button

This button feeds paper.

(Power) LED

This LED is on when the printer is on.

ERROR LED

This indicates an error.

PAPER OUT LED

On indicates a paper near end or out. Flashing indicates standby.

Important Notes on Installation

❏For a serial interface, you must use a null modem cable, also called a cross

cable.

❏For a parallel interface, use a cable that meets the specifications for an IEEE

1284-compliant cable.

❏For a USB interface, install the printer driver before connecting the printer.

Installing the Printer

You can install this printer only horizontally.

Fix the printer so that it does not move around when you open the printer cover

and cut roll paper. A tape for fixing the printer is available as an option.

As shown in the illustration C, install the printer with a maximum tilt of 3°.

Installing the printer with a tilt of more than 3° may cause the following problems.

• Roll paper near end cannot be detected.

• The printer cover will not close after installing roll paper.

• Roll paper cannot be taken out.

Using the Power Switch Cover

WARNING:

If an accident occurs with the power switch cover attached, unplug the power

cord immediately. Continued use may cause fire or shock.

The enclosed power switch cover ensures that the power switch is not pressed

accidentally. To use this cover, install it as shown in illustration D.

Andere Handbücher für TM-T70

Inhaltsverzeichnis

Sprachen:

Andere Epson Drucker Handbücher

Epson

Epson TM-H6000IV-DT Gebrauchs- und Pflegehandbuch

Epson

Epson SC-P9500 Series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Epson

Epson Stylus CX7300 Series Bedienungsanleitung

Epson

Epson Mobilink TM-P60 Bedienungsanleitung

Epson

Epson WF-2860 Series Bedienungsanleitung

Epson

Epson SC-P900 Series Bedienungsanleitung

Epson

Epson EcoTank ET-1110 Series Bedienungsanleitung

Epson

Epson WorkForce 1100 Bedienungsanleitung

Epson

Epson WF-2650 Bedienungsanleitung

Epson

Epson SC-S30600 Bedienungsanleitung

Epson

Epson TM-H6000IV-DT Bedienungsanleitung

Epson

Epson A251B Bedienungsanleitung

Epson

Epson Stylus Pro 3880 Graphic Arts Edition Programmierhandbuch

Epson

Epson EPL-5700 Bedienungsanleitung

Epson

Epson SC-T5100 Series Bedienungsanleitung

Epson

Epson WF-6590 series Bedienungsanleitung

Epson

Epson Stylus Office BX935FWD Montageanleitung

Epson

Epson Stylus TX121 Bedienungsanleitung

Epson

Epson C264011 - Stylus Photo 1200 Color Inkjet... Abmessungen

Epson

Epson TM-L90 series Bedienungsanleitung

Epson

Epson LQ-1150 II Bedienungsanleitung

Epson

Epson L800 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung