Equinox Systems TRICLOPS EQLED50 Bedienungsanleitung

Order code: EQLED50

user manual

www.prolight.co.uk

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Equinox Triclops Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the Equinox carton the following items:

1, Equinox Triclops 2, Power cable 3, Instruction manual

Technical Specications:

DMX channels: 9

Voltage: AC 240V - 50Hz

72 Ultra bright LED’s (R: 24, G: 24, B:24)

Fuse: 1 Amp

Power Consumption: 20W

Dimensions: 390 x 166 x 325mm

Weight: 4.3Kg

Operations:

There are 4 operating modes to choose from:

1, DMX mode 2, Auto Run mode 3, Sound active mode 4, Slave mode

DMX Mode

To select DMX mode, set dip switch 10 to ON. You can now set the required DMX address using

dip switches 1 to 9. The start address for this xture is 0. Please refer to the chart below for DMX

functions.

Auto Run Function Mode

To select auto pattern mode, set all dip switches to the OFF position. The unit will now cycle

through all it’s built-in patterns. In this mode the LEDs will remain constantly chasing until the

power is turned OFF or the mode is changed.

Sound Active Mode

To select sound active mode set dip switch 9 to ON. You can now use the sensitivity control on the

back panel to set the required sound input level. With no music present, the LEDs will turn OFF

and will come back ON as soon as the music starts again.

Slave Mode

To select the slave mode set dip switch 9 to OFF and others to ON. The slave units will now follow

in conjunction with the master unit.

Note: The master unit can be run in any mode for the slave units to follow.

Equinox Triclops Technical specications

Overview

DMX Function Chart

Equinox Triclops Overview

Back

Bottom Side

Identication:

1, Hanging bracket

2, DMX in

3, DMX out

4, Dip switches

5, IEC Power In/Out sockets

6, Fuse

7, Microphone

8, Sound sensitivity control

9, Cooling fan

1 0-255 No Function

0-255

N/A

0-251

252-255

0-251

252-255

0-251

252-255

0-255

Tilts top mirror up and down

Tilts bottom right mirror up and down

Tilts bottom left mirror up and down

Not used

Pattern selector, 1 to 15 (top mirror)

Blackout (top mirror)

Pattern selector, 1 to 15 (bottom right mirror)

Blackout (bottom right mirror)

Pattern selector, 1 to 15 (bottom left mirror)

Blackout (bottom left mirror)

Speed control

Channel Value Function

Further DMX cables can be purchased

from all good sound and lighting suppliers

or Prolight dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Triclops can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Equinox Triclops DMX Set up

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Equinox Triclops DMX Set up

Equinox Triclops Dip Switch Reference Chart

DMX Dip Switch Quick Reference Chart

Dip Switch Position

Dip Switch position DMX Address

www.prolight.co.uk

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems SF-300 Bedienungsanleitung

Equinox Systems

Equinox Systems CONSTELLA Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED203 Bedienungsanleitung

Equinox Systems

Equinox Systems Vortex Bedienungsanleitung

Equinox Systems

Equinox Systems MidiPar Tri Plus Bedienungsanleitung

Equinox Systems

Equinox Systems Comet EQLED29 Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Tri Bedienungsanleitung

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung

Equinox Systems

Equinox Systems Interceptor MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Megabar System EQLED63 Bedienungsanleitung

Equinox Systems

Equinox Systems VEGA EQLA16 Bedienungsanleitung

Equinox Systems

Equinox Systems KAMIKAZE EQLA14 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Flower EQLED77 Bedienungsanleitung

Equinox Systems

Equinox Systems Saturn Spot Bedienungsanleitung

Equinox Systems

Equinox Systems Terminator 2 Bedienungsanleitung

Equinox Systems

Equinox Systems QUADZILLA Bedienungsanleitung

Equinox Systems

Equinox Systems Spectra Strobe Batten Bedienungsanleitung

Equinox Systems

Equinox Systems PREDATOR Bedienungsanleitung

Equinox Systems

Equinox Systems ATRIA Bedienungsanleitung

Equinox Systems

Equinox Systems QUADRILLE Bedienungsanleitung

Equinox Systems

Equinox Systems VIXEN EQLA36 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED65 Giga Bar System Bedienungsanleitung

Equinox Systems

Equinox Systems VS 1500 Fogger Bedienungsanleitung

Equinox Systems

Equinox Systems Cirrus Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung