Equinox Systems Power Flower EQLED77 Bedienungsanleitung

User manual

Order code: EQLED77

Order code: EQLED79

IMPACT

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Equinox Power Flower & Impact Flower Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 100V/240V.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

LED failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the carton the following items:

1, Fixture 2, Power cable 3, User manual

Technical Specications:

Overview

Equinox Power Flower & Impact Flower Technical specications

Identication:

1. Hanging bracket

2. Earth point

3. Safety eye

4. LED display

5. Function buttons

6. DMX input socket

7. DMX output socket

8. IEC power in socket

9. IEC power out socket

10. Hanging bracket tightening knobs

11. Fuse - 1A, 240V

EQLED79 Impact Flower

• DMX channels: 1, 3 or 5 selectable

• Sound activated, auto, DMX and master/slave

• 1 x 20W white COB LED

• 11 solid colour gobos with mirror dish

• 4 Push button LED digital display

• 0-100% dimming and variable strobe via DMX

• IEC Power in/out sockets

• 3-pin XLR in/out sockets

• Power consumption: 45W

• Power supply: 100-240V, 50/60Hz

• Dimensions: 232 x 281 x 260mm

(195mm with bracket folded)

• Weight: 4.3kg

EQLED77 Power Flower

• DMX channels: 1, 3 or 5 selectable

• Sound activated, auto, DMX and master/slave

• 1 x 20W white COB LED

• Multicolour reector dish and 11 gobos

• 4 Push button LED digital display

• 0-100% dimming and variable strobe via DMX

• IEC Power in/out sockets

• 3-pin XLR in/out sockets

• Power consumption: 45W

• Power supply: 100-240V, 50/60Hz

• Dimensions: 232 x 281 x 260mm

(195mm with bracket folded)

• Weight: 4.3kg

Equinox Power Flower & Impact Flower Operation Modes

Operation modes:

DMX mode:

To access the DMX mode, press the “MODE” button on the rear of the unit to show 512 on the

LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the

desired DMX address from d.OO1~ d.512, and press the “ENTER” button to conrm the setting.

DMX channel mode:

To access the DMX channel mode, press the “MODE” button on the rear of the unit to show 512

on the LED display. Then press the “ENTER” button and use the “UP” and “DOWN” buttons to

set the desired DMX address from d.OO1~ d.512. Now press the “ENTER” button to choose

one of the 1, 3 or 5 DMX channel modes use the “UP” and “DOWN” buttons, and press the

“ENTER” button to conrm the setting.

3 channel DMX chart:

0-14

15-29

30-44

45-59

60-74

75-89

90-104

105-119

120-134

135-149

150-164

165-209

210-255

0-179

180-214

215-255

0-255

Channel Value Function

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 9

Gobo 10

Gobo 11

Gobo wheel clockwise rotation

Gobo wheel anti-clockwise rotation

Mirror dish 360 degree rotation

Mirror dish clockwise rotation

Mirror dish anti-clockwise rotation

LED brightness 0-100%

0-7

8-67

68-127

128-187

188-247

248-255

Channel Value Function

No function (Blackout)

Show (Program 1)

Show (Program 2)

Show (Program 3) - Slow motion mode

Sound active (188 = Low sensitivity, 247 = High sensitivity)

Random shows

1 channel DMX chart:

Equinox Power Flower & Impact Flower Operation Modes

To exit out of any of the above options, press the “MODE” button.

Master/slave mode

To access the master/slave mode, press the “MODE” button on the rear of the unit to show

SLAv on the LED display and press the “ENTER” button to conrm the setting. The unit will

now run in sequence with the master unit.

Please ensure that all slave units are set to the same DMX channel mode as the master unit.

Sound active mode:

To access the sound active mode, press the “MODE” button on the rear of the unit to show

SUNd on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN”

buttons to set the sound sensitivity level from SU.OO~ SU.31 and press the “ENTER” button

to conrm the setting.

Note: SU00 = Low, SU31 = High

To exit out of any of the above options, press the “MODE” button.

5 channel DMX chart:

0-14

15-29

30-44

45-59

60-74

75-89

90-104

105-119

120-134

135-149

150-164

165-209

210-255

0-179

180-214

215-255

0-255

0-19

20-255

0-17

18-255

Channel Value Function

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 9

Gobo 10

Gobo 11

Gobo wheel clockwise rotation

Gobo wheel anti-clockwise rotation

Mirror dish 360 degree rotation

Mirror dish clockwise rotation

Mirror dish anti-clockwise rotation

LED brightness 0-100%

No function

Sound active

No function

Strobe (slow to fast)

(When in sound active 0-255 = sensitivity)

Equinox Power Flower & Impact Flower Operation Modes

Auto run mode:

To access the auto run mode, press the “MODE” button to show AUTO on the rear of the unit.

In the auto run mode there are three setting options to choose from:

Gobo - Gobo setting options

roAt - Gobo rotation options

led - LED setting options

Gobo setting options:

While in the auto mode, press the “MODE” button to show Gobo on the rear of the unit.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose one of

the 5 options.

GorG = Static gobo

G-cЅ = Spins the gobo wheel in a clockwise direction. In this menu, press the “ENTER”

button then us the “UP” or “DOWN” buttons to select the speed.

GccЅ = Spins the gobo wheel in a anti-clockwise direction. In this menu, press the “ENTER”

button then us the “UP” or “DOWN” buttons to select the speed.

GPoS = Gobo selector. In this menu, press the “ENTER” button and then use the up and down

buttons to scroll through the 11 static gobos

G.Pro = Spins the gobo wheel clock wise and anti-clock wise.

To exit out of any of the above options, press the “MODE” button.

Equinox Power Flower & Impact Flower Operation Modes

Mirror dish rotation options:

While in the auto mode, press the “MODE” button to show roAt on the rear of the unit.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose one of

the 4 settings.

r.orG = Static mirror dish

r.-cЅ = Spins the mirror dish in a clockwise direction. In this menu, press the “ENTER”, enter the

rotating speed settings, through the “UP” or “DOWN” to select the speed with 10 increments.

r.ccЅ = Spins the mirror dish in a anti-clockwise direction. In this menu, press the “ENTER”,

enter the rotating speed settings, through “UP” or “DOWN” to select the speed with 10 increments.

rPro = Spins the mirror dish clockwise and anti-clockwise whilst running the built-in programs.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MODE” button.

LED setting options:

While in the auto mode, press the “MODE” button to show led on the rear of the unit.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose one of the 2

settings by pressing the “ENTER” button and using the “UP” and “DOWN” buttons accordingly

and press the “ENTER” button to conrm the setting.

e.con = Set the brightness of the LED from 000-255 (000=off, 255=full on). In this menu,

press the “ENTER” button, through the “UP” or “DOWN” to set the chosen brightness.

e.pro = Sets the led into fade in and fade mode. Fade speed can be set from 00-15

(00=slow, 15=fast). In this menu, press the “ENTER” button, through the “UP” or “DOWN”

to set the chosen fade speed.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MODE” button.

Note: After completing your settings, the auto run mode will run according to your settings.

Built-in programs mode

To access the built-in programs mode, press the “MODE” button on the rear of the unit to show

Pro on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN”

buttons to select between the program options:

Pro1 = This program is set to a slow rotation with fade in and fade out.

Pro2 = This program is set to a fast rotation with fade in and fade out.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MODE” button.

Equinox Power Flower & Impact Flower Operation Modes

Factory reset menu mode

Error reset:

Note: you only need to go into this mode if the rear of the unit shows -err

on the LED display on start up.

To access the setting mode, press the “MODE” button on the rear of the unit to show Set

on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to

choose one of the 3 settings by pressing the “ENTER” button and using the “UP” and “DOWN”

buttons accordingly.

o-St = Set the offset of the gobo wheel from 0 - +100 or -100.

The user can adjust the gobo wheel to the correct position via this option if the image

of the gobo is partially obscured.

нoto = Review the motor reset status.

If the LED display shows G-nG then the gobo wheel motors position is incorrect.

If the LED display shows G-oѢ then the gobo wheel motor has reset successfully.

If the LED display shows r-nG then the rotation wheel motors position is incorrect.

If the LED display shows r-oѢ then the rotation wheel motor has reset successfully.

-rSt = Resets the unit to its factory settings.

To exit out of the above, press the “MODE” button until you are back at the main menu.

Total reset:

In addition, if the xture is not operating properly after powering on and menu is not operating

normally, press the “MODE” and “ENTER” buttons at the same time, then power on, until the

LED display ashes then release the buttons. Note: This will also restore the factory settings.

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

Equinox Power Flower & Impact Flower DMX set up

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the xture and each xture independently.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each xture requires a

“start address” from 1- 511. A xture requiring one or more channels for control begins to read the

data on the channel indicated by the start address. For example, a xture that occupies or uses 7

channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Power Flower can be controlled via DMX-512 protocol. The DMX address is set on

the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems Gigabar MKII COB Bedienungsanleitung

Equinox Systems

Equinox Systems NEBULA Bedienungsanleitung

Equinox Systems

Equinox Systems Goboceptor Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par Series Bedienungsanleitung

Equinox Systems

Equinox Systems UV Mini Batten 9 Bedienungsanleitung

Equinox Systems

Equinox Systems GEOMETRIX EQLA35 Bedienungsanleitung

Equinox Systems

Equinox Systems CARINA Bedienungsanleitung

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung

Equinox Systems

Equinox Systems MidiPar Tri Plus Bedienungsanleitung

Equinox Systems

Equinox Systems GEMINI Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED008 Bedienungsanleitung

Equinox Systems

Equinox Systems SCORPIO EQLA11 Bedienungsanleitung

Equinox Systems

Equinox Systems ORION Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Tri Bedienungsanleitung

Equinox Systems

Equinox Systems Lighting strike STRO21 Bedienungsanleitung

Equinox Systems

Equinox Systems QUADRILLE Bedienungsanleitung

Equinox Systems

Equinox Systems SF-300 Bedienungsanleitung

Equinox Systems

Equinox Systems Krypton EQLED21 Bedienungsanleitung

Equinox Systems

Equinox Systems Vortex Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED032A Bedienungsanleitung

Equinox Systems

Equinox Systems Domin8r IIEQLED53 Bedienungsanleitung

Equinox Systems

Equinox Systems Axis 50W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems Nova Par 64 Bedienungsanleitung

Equinox Systems

Equinox Systems ATRIA Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung