Equinox Systems EQLED65 Giga Bar System Bedienungsanleitung

www.prolight.co.uk

ORDER CODE: EQLED65

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Equinox Giga Bar Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 100V/240V.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the carton the following items:

1, Equinox Giga Bar and bag 2, Power cable 3, User manual 4, Stand and bag

5, I.R remote 6, GB-1 foot controller 7, 4 pcs 25 degree lense kit

Technical Specications:

4 x 30W Tri-colour RGB COB LEDs

Beam angle: 25/90 degrees

0-100% dimming and variable strobe (via DMX)

DMX channels: 3, 4, 5, 6, 7, 8, 12 and 17 selectable

Operating modes: 1, Sound activated

2, Built-in programmes

3, Auto Run

4, DMX

5, Slave

Infra-red operation (remote included)

14 built-in programmes

4 push button menu with LCD digital display

3-pin XLR In/Out sockets for DMX

5-pin socket for foot controller (GB-1)

Powercon in/out sockets

2 x IEC power out sockets (switchable via I.R remote)

Power consumption: 120W

Power supply: 100V-240V AC~60Hz-50Hz

Dimensions: 1000 x 82 x 320mm

Weight: 7.6kg

Fuse: F2A 250V (3A 125V)

Overview

DMX IN DMX OUT

FOOT

SWITCH

FUSE:

F3A

POWER OUT 1 POWER OUT 2

POWER

OUT

POWER

FUSE:

F3A

100-240V

50Hz / 60Hz

MODE ENTER UP DOWN

Equinox Giga Bar Technical Specications

Identication:

1, 28mm spigot

2, Mode button

3, Enter button

4, Up button

5, Down button

6, IEC Power out 1

7, IEC Power out 2

8, DMX in

9, DMX out

10, 5-pin footswitch socket

11, LCD display

12, Output to lights

13, I.R LED

14, I.R sensor

15, Powercon in

16, Powercon out

Equinox Giga Bar Operation Modes

Setup:

1, Setting dimmer curves

To set the dimmer curves, press the “MODE” button to show “DIM CURVE” in the LCD display

window. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select LED or

halogen.

2, Setting static colour for each LED panel

To set the static colour for each LED panel, press the “MODE” button to show “DIMMER” in

the LCD display window. Now press the “ENTER” button and use the “UP” and “DOWN”

buttons to select the LED panel from 01-04. Now press the “ENTER” button to set the brightness

of the selected LED panel. Using the “UP” and “DOWN” buttons set the LED panel to the desired

brightness (R: 0-99, G: 0-99, B: 0-99).

3, Setting master dimmer

To set the master dimmer, press the “MODE” button to show “MASTER DIMMER” in the LCD

display window. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set

the master dimmer from 0-99. This will effect all the modes except DMX and I.R remote.

4, Setting ow invert

To set the ow invert, press the “MODE” button to show “FLOW INVERT” in the LCD display

window. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the ow

invert to on or off.

5, Setting I.R remote

To set the I.R remote, press the “MODE” button to show “IR ACTIVE” in the LCD display window.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the I.R remote to

on or off.

Operation modes:

1, Sound active mode

To select the sound active mode, press the “MODE” button to show “SOUND MODE” in the LCD

display window. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to

adjust the sound sensitivity level (SENS00-31) and press the “ENTER” button again to adjust the

frequency level (FQN01-99). Finally press the “ENTER” button to conrm your setting.

2, Built-in programmes mode

To access the built-in programme mode, press the “MODE” button to show “01.STATIC” in the

LCD display window. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to

choose one of the 14 built-in programmes (01-14) (see table overleaf).

To choose one of the seven colours in the “STATIC” mode, press the set “ENTER” button and

use the “UP” and “DOWN” buttons to choose one of the following 15 colours.

To adjust the speed level in the remaining 13 built-in programmes, press the “ENTER” button and

use the “UP” and “DOWN” buttons to set the desired speed level (00-99).

To adjust the ash speed press the “ENTER” button and use the “UP” and “DOWN” buttons to

set the desired ash speed level (00-99). Finally press the “ENTER” button to conrm

your setting.

3, Auto Run mode

To select the Auto run mode, press the “MODE” button to show “AUTO RUN” in the LCD display

window. Now press the “ENTER” button to adjust the frequency level (FQN01-99). Finally press

the “ENTER” button to conrm your setting. The unit will now run all 15 built-in programmes one

after another.

4, DMX mode

To select the DMX mode, press the “MODE” button to show “DMX MODE” in the LCD display

window. Press the “ENTER” button and use the “UP” and “DOWN” buttons to set a DMX

address from 001-512. Now press the “ENTER” button again and use the “UP” and “DOWN”

buttons to choose one of the 8 DMX channel settings (3, 4, 5, 6, 7, 8, 12, or 17) Finally press the

“ENTER” button to conrm your setting (see DMX chart). The starting address for this xture

is 001.

DMX Charts

3 channel mode:

Channel Value Function

1 000-255 Red (0-100%)

2 000-255 Green (0-100%)

3 000-255 Blue (0-100%)

4 channel mode:

CH1 CH2 CH3 CH4

000-036 R 000-036 R 000-036 R 000-036 R

037-073 G037-073 G037-073 G037-073 G

074-110 B074-110 B074-110 B074-110 B

111-147 RG 111-147 RG 111-147 RG 111-147 RG

148-184 RB 148-184 RB 148-184 RB 148-184 RB

185-221 GB 185-221 GB 185-221 GB 185-221 GB

222-255 RGB 222-255 RGB 222-255 RGB 222-255 RGB

5 channel mode:

CH1 R 0-255 Dimming 0-100%

CH2 G0-255 Dimming 0-100%

CH3 B0-255 Dimming 0-100%

CH4 0-127: Light 1 OFF (add light to aux power out 1 on top of the bar)

128-255: Light 1 ON (add light to aux power out 1 on top of the bar)

CH5 0-127: Light 2 OFF (add light to aux power out 2 on top of the bar)

128-255: Light 2 ON (add light to aux power out 2 on top of the bar)

Equinox Giga Bar Operation Modes

6 channel mode:

CH1 R1, R2 0-255 Dimming 0-100%

CH2 G1, G2 0-255 Dimming 0-100%

CH3 B1, B2 0-255 Dimming 0-100%

CH4 R3, R4 0-255 Dimming 0-100%

CH5 G3, G4 0-255 Dimming 0-100%

CH6 B3, B4 0-255 Dimming 0-100%

7 channel mode:

CH1 R 0-255 Dimming 0-100%

CH2 G0-255 Dimming 0-100%

CH3 B0-255 Dimming 0-100%

CH4 DIMMER 0-255 Dimming 0-100%

CH5 0 No function

1-5 Sound sensitivity from

low to high

6-10 No function

11-255 Strobe from slow to

fast

CH6 0-127: Light 1 OFF (add light to aux power out 1 on top of the bar)

128-255: Light 1 ON (add light to aux power out 1 on top of the bar)

CH7 0-127: Light 1 OFF (add light to aux power out 1 on top of the bar)

128-255: Light 1 ON (add light to aux power out 1 on top of the bar)

Equinox Giga Bar Operation Modes

8 channel mode:

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

0-15

Master

Dimmer

(0-255)

Flash

(0-255)

from

slow to

fast

(0-255)

0-127:

Light

1 OFF

(add light

to aux

power

out 1 on

top of the

bar)

128-255:

Light

1 ON

(add light

to aux

power

out 1 on

top of the

bar)

0-127:

Light

2 OFF

(add light

to aux

power

out 2 on

top of the

bar)

128-255:

Light

2 ON

(add light

to aux

power

out 2 on

top of the

bar

16-23 R

24-31 G

32-39 B

40-47

48-55

56-63

64-71

RGB

72-79

Colour1

80-87

Colour2

88-95

Colour3

96-103

Colour4

104-111

Colour5

112-119

Colour6

120-127

Colour7

128-135

Colour8

136-143

Dream

Speed

(0-255)

from

slow to

fast

144-151

Meteor

152-159

Fade

160-167

Change

168-175

Flow1

176-183

Flow2

184-191

Flow3

192-199

Flow4

200-207

Flow5

208-215

Flow6

216-223

Flow7

224-231

Flow8

0-255

Select 8

colours

0-255

Select 8

colours

232-239

Flow9

240-255

Sound

Active

Sensitivity

(0-255)

Equinox Giga Bar Operation Modes

12 channel mode:

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12

R1 G1 B1 R2 G2 B2 R3 G3 B3 R4 G4 B4

Equinox Giga Bar Operation Modes

17 channel mode:

CH1 CH2 CH3 CH4 CH5 CH6 CH15 CH16 CH17

0-15

Master

Dimmer

(0-255)

Flash

(0-255)

from

slow to

fast

(0-255)

0-127:

Light

1 OFF

(add light

to aux

power

out 1 on

top of the

bar)

128-255:

Light

1 ON

(add light

to aux

power

out 1 on

top of the

bar)

0-127:

Light

2 OFF

(add light

to aux

power

out 2 on

top of the

bar)

128-255:

Light

2 ON

(add light

to aux

power

out 2 on

top of the

bar

16-23 R

24-31 G

32-39 B

40-47

48-55

56-63

64-71

RGB

72-79

Colour1

80-87

Colour2

88-95

Colour3

96-103

Colour4

104-111

Colour5

112-119

Colour6

120-127

Colour7

128-135

Colour8

136-143

Dream

Speed

(0-255)

from

slow to

fast

144-151

Meteor

152-159

Fade

160-167

Change

168-175

Flow1

Andere Handbücher für EQLED65 Giga Bar System

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems COBALT Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit MKII Bedienungsanleitung

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung

Equinox Systems

Equinox Systems MidiPar Tri Plus Bedienungsanleitung

Equinox Systems

Equinox Systems Interceptor MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Vortex Bedienungsanleitung

Equinox Systems

Equinox Systems Terminator 2 Bedienungsanleitung

Equinox Systems

Equinox Systems Nimbus Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT XP Bedienungsanleitung

Equinox Systems

Equinox Systems VEGA EQLA16 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par Series Bedienungsanleitung

Equinox Systems

Equinox Systems Lexor Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Saber Bedienungsanleitung

Equinox Systems

Equinox Systems Gigabar MKII COB Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Lithium Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Lighting strike STRO21 Bedienungsanleitung

Equinox Systems

Equinox Systems SCORPIO EQLA11 Bedienungsanleitung

Equinox Systems

Equinox Systems KAMIKAZE EQLA14 Bedienungsanleitung

Equinox Systems

Equinox Systems CARINA Bedienungsanleitung

Equinox Systems

Equinox Systems PIXELpoint Batten Bedienungsanleitung

Equinox Systems

Equinox Systems UV Mini Batten 9 Bedienungsanleitung

Equinox Systems

Equinox Systems Saturn Spot Bedienungsanleitung

Equinox Systems

Equinox Systems TRICLOPS EQLED50 Bedienungsanleitung

Equinox Systems

Equinox Systems Goboceptor Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung