Ericsson M-PA EDACS Bedienungsanleitung

Mobile Communications

LBI-38407D

Operator’s Manual

EDACSM-PA

PORTABLE RADIOS

May 1991, Ericsson Mobile Communications AB

Table of Contents

INTRODUCTION . . . . . . . . . 5

CONTROLS . . . . . . . . . . . 7

ON/OFF SWITCH . . . . . . . 7

VOLUME CONTROL KNOB . . 7

CONTROL KNOB . . . . . . . 7

PTT BUTTON . . . . . . . . . . 8

MONITOR BUTTON . . . . . . 8

Trunked Mode . . . . . . . . 8

Conventional Mode . . . . . . 8

EMERGENCY BUTTON . . . . 9

STEP BUTTON

(Scan And System Models Only) 9

SCAN BUTTON

(Scan And System Models Only) 10

Table of Contents

(Continued)

SPC BUTTON

(Scan And System Models Only) 10

2nd BUTTON

(Scan And System ModeIs Only) 11

ADD/DELETE BUTTON

(Scan And System Models Only) 11

LOCK BUTTON

(Scan And System ModeIs Only) 11

STO BUTTON (Shifted Digit 1 -

System Model Only) . . . . . . 11

RCL BUTTON (Shifted Digit 3 -

System Model Only) . . . . . . 12

CLR BUTTON (Shifted # Button-

System Model Only) . . . . . . 12

STS BUTTON (Shifted Digit -

System Model Only) . . . . . . 12

INDICATORS . . . . . . . . . . . 12

UNIVERSAL DEVICE

CONNECTOR . . . . . . . . . . 14

ALERT TONES . . . . . . . . . . 14

OPERATION . . . . . . . . . . . 15

POWER-UP . . . . . . . . . . 15

SYSTEM/GROUP/CHANNEL

SELECTION . . . . . . . . . . 15

This manual is published by

Ericsson GE Mobile

Communications Inc.

, without any warranty. Im-

provements andchangestothismanualnecessitated

by typographical errors, inaccuracies of current infor-

mation, or improvements to programs and/or equip-

ment, may be made by

Ericsson GE Mobile

Communications Inc.

, at any time and without no-

tice. Such changes will be incorporated into new

editions of thismanual. No part ofthismanual maybe

reproduced or transmitted in any form or by any

means, electronic or mechanical, including photo-

copying and recording, for any purpose, without the

express written permission of

Ericsson GE Mobile

Communications Inc.

Table of Contents

(Continued)

STEP Button Programmed For

System Selection; CONTROL

KNOB Programmed For Group

And Channel Selection . . . . 16

CONTROL KNOB Programmed

For System Selection; STEP

Button Programmed For Group

And Channel Selection . . . . 17

TRUNKED MODE OPERATION 17

Receiving A Message . . . . . 17

Sending A Message . . . . . . 19

Emergency Operation

(Trunked Mode) . . . . . . . . 19

Dynamic Regrouping . . . . . 20

Wide Area System Scanning . 20

Scanning Trunked Groups (Scan

And System Models Only) . . . 21

SpeciaI CaIIs . . . . . . . . . 22

SYSTEM MESSAGE OPERATION

(System Model Only) . . . . . . 27

CONVENTIONAL MODE

OPERATION . . . . . . . . . . . 27

Receiving A Message . . . . . 27

Sending A Message . . . . . . 28

Emergency Operation

(Conventional Mode) . . . . . 29

Scanning Conventional

Channels (Scan And System

Models Only) . . . . . . . . . . 29

Table of Contents

(Continued)

Telephone Interconnect

Calls (Scan And System

ModeIs Only) . . . . . . . . . 31

OPERATING TIPS . . . . . . . . 31

OPERATING RULES

AND REGULATIONS . . . . . . . 32

BATTERY PACKS . . . . . . . . . 33

INSTALLING THE BATTERY

PACK . . . . . . . . . . . . . . 33

REMOVING THE BATTERY

PACK . . . . . . . . . . . . . . 33

CHARGING THE BATTERY

PACKS . . . . . . . . . . . . . . 34

RECHARGEABLE BATTERY

PACK DISPOSAL . . . . . . . . 35

SWIVEL MOUNT REMOVAL AND

REPLACEMENT . . . . . . . . . . 35

INTRINSICALLY SAFE USAGE . . 36

BATTERY PACKS . . . . . . . . 36

ACCESSORIES . . . . . . . . . 37

WARRANTY . . . . . . . . . . . . 38

NICKEL-CADMIUM BATTERY

WARRANTY . . . . . . . . . . . . 39

CONTROLS

ON/OFF SWITCH

The ON/OFF SWITCH is located on

the battery pack. Sliding this switch up will

supply power to the radio from the battery

pack. An audible click will be heard and

the ‘ON" indicator will be exposed. When

the radio is turned on, it will perform a

power-up self test and resume operating

on the previous group or channel. Sliding

the switch down will turn the radio off.

VOLUME CONTROL KNOB

The VOLUME CONTROL KNOB is a

rotatable control on the top of the radio

used to adjust the receiver’s volume level

in the speaker. Rotating this knob in a

clockwise direction will increase the vol-

ume and counter-clockwise rotation will

decrease the volume. Minimum volume

levels can be programmed into the radio to

prevent missed calls when the knob is

rotated fully counter-clockwise.

CONTROL KNOB

Figure 1 - Side View (All Models) Figure 2 - Select Model

INTRODUCTION

The EDACSM-PASelect, Scan

and System model radios are high-quality

microprocessor-controlled synthesized

two-way FM portable radios. These full-

featured radios are designed for operation

inEDACS(EnhancedDigitalAccessCom-

munications System) trunking systems

and conventional radio systems. M-PAop-

eration is highlighted by the radio’s pro-

gramming versatility. This permits custom

operation of each radio to meet the needs

of the radio system and the individual us-

ers.

This manual describes operating pro-

cedures for the three (3) different radio

models.

The M-PA Select model radio is the

basic version of the radio that can be pro-

grammed with up to sixteen (16) inde-

pendent trunked groups and/or

conventional radio channels. This unit fea-

tures an eight-digit alphanumeric liquid

crystal display (LCD) and a 16-position

knob for group/channel selection. The dis-

play also has status flags that indicate

various operating modes and it is backlit

for nighttime and low-level ambient light

operation.

Scan and System model radios have

an LCD similar to the Select model radio.

These radios have front panel keypads

that provide additional operating features

not available on the Select model radio.

The Scan model radio has a 4-button key-

pad and the System model radio has a

16-button keypad. Additional features in-

clude expanded system and group/chan-

nel selection capability, trunked group and

conventional channel scan capability,

trunkedmodeindividualcallcapability,and

telephone interconnect call capability. The

numeric keypad on the System model ra-

dio also allows storage of ten (10) opera-

tor-entered telephone numbers and ten

(10) operator-entered radio ID numbers.

These numbers can be recalled at will and

initiated. Manually dialed telephone inter-

connect with overdial capability and con-

ventional mode DTMF dialing is also

provided by the Systemmodel’s 16-button

keypad.

Figure 3 - Scan Model Figure 4 - System Model

The rotatable 16-position CONTROL

KNOB located on the top of the radio pro-

vides system, group or channel selection

accordingtohowtheradioisprogrammed.

A stop plate may be installed under the

knob to limit the maximum number of po-

sitions to less than sixteen (16). It is nor-

mally factory installed for fifteen (15)

positions.

On the Select model radio, the CON-

TROL KNOB selects any one of trunked

systems and groupsor conventionalchan-

nels programmed into the radio.

On Scan and System model radios,

the CONTROL KNOB is used in combina-

tion with the keypad to select a specific

trunked system and group or a conven-

tional channel. The selection method is

determined by the radio’s programming.

See the section entitled "SYS-

TEM/GROUP/CHANNEL SELECTION" in

the "OPERATION" section of this manual

for details.

PTT BUTTON

Pressing the PTT BUTTON on the

side of the radio turns on the radio‘s trans-

mitter. The "TX" status flag in the display

will turn on when the radio is transmitting.

Releasing the PTT BUTTON will return

operation to receive mode.

When operating on a trunked system,

the radio may be programmed to automat-

ically transmit (without the operator press-

ing the PTT BUTTON) to maintain

communicationwiththesitecontroller.The

"TX" status flag in the display will turn on

when the radio is transmitting.

MONITOR BUTTON

Trunked Mode

The exact operation of a particular ra-

dio will vary depending upon its mode of

operation, its programming, and the par-

ticular radio system. Consult a radio sys-

tem’s representative for particular features

that are programmed into the radio.

The radio operates in trunked mode

when a trunked system is selected and it

operates in conventional mode when a

conventional system is selected.

When operating on a trunked system

in special call mode, pressing the MONI-

TOR BUTTON after an individual call has

been received will return the radio to the

groupcallmode.Inthiscondition,theradio

will not respond on an individual basis but

it will then transmit group calls upon sub-

sequent activations of the PTT BUTTON.

The radio will also automatically return to

the group call mode after the programmed

individual call-back time-out period ex-

pires.

This button is also used to toggle be-

tween group and regroup settings if the

Dynamic Regrouping mode (with deselect

capability) has been activated by the site

controller.

On the System model radio, pressing

the MONITOR BUTTON will clear all digits

entered from the numeric keypad and re-

turntheradiototheselectedgroupdisplay.

Conventional Mode

Whentheradioisoperatinginconven-

tional mode (on a conventional channel),

the MONITOR BUTTON is used to tempo-

rarily unsquelch the receiver so channel

traffic can be monitored. Momentarily

pressing it will unsquelch the receiver.

If the selected channel has Channel

Guard (CG) and/or Type 99 (T99) coded-

squelch tone decode feature programmed

for the selected channel, this button is can

also be used to enable and disable the

programmed feature. Repeated activa-

tions will toggle CG and/or T99 between

the enabled (on) and disabled (off) states.

To toggle the programmed feature, press

and hold the MONITOR BUTTON for at

least two (2) seconds until the appropriate

status flag in the display toggles.

The MONITOR BUTTON is also used

to reset the radio after a Type 99 (T99)

selective call has been successfully re-

ceived. If the radio is operating in a Type

99 mode, momentarily press the MONI-

TOR BUTTON to reset the radio after a

T99 call is successfully received.

EMERGENCY BUTTON

When the radio is operating in trunked

mode, pressing and holding the red

EMERGENCY BUTTON on top of the ra-

dio for approximately one (1) second will

initiate an emergency call on the pro-

grammed home group. If no home group

is programmed into the radio the emer-

gency call will be transmitted on the se-

lected group.

In conventional mode, initiating an

emergency call by pressing the EMER-

GENCY BUTTON will cause the radio to

transmit GE-STAR emergency signaling

on the programmed emergency channel.

If no emergency channel is programmed,

GE-STAR emergency signaling will be

transmitted on the selected channel.

STEP BUTTON

(Scan And System Models Only)

The STEP button located on the key-

pad can be programmed to select trunked

groupsandconventionalchannelsoritcan

beprogrammedtoselectsystems.Seethe

section entitled "SYSTEM/GROUP/

CHANNEL SELECTION" for details.

STEPis also used to scroll through the

programmed special call table when the

special call mode is enabled.

SCAN BUTTON

(Scan And System Models Only)

Pressing the SCAN button on the key-

pad will toggle scan operation on and off

When the radio is scanning, the "SCN"

status flag in the display willturn on and all

groups/channels on the scan list in the

current system will be scanned.

SPC BUTTON

(Scan And System Models Only)

Pressing SPC will switch operation

from the group select mode to the special

call mode. The last selected special call

will be displayed.

While in special call mode, the next

programmed special call can be selected

by pressing STEP. Pressing 2nd then

STEPwill select the previous programmed

special call. The caller’s ID of the last

received individual call and the last re-

ceivedgroupcallontheselectedgroupare

a selectable using this method. See "Spe-

cial Calls" for details.

2nd BUTTON (Scan And System

ModeIs Only)

On an M-PAScan model radio the two

(2) centerbuttons (SCAN and SPC)on the

keypad are dual-function buttons. The

second or shifted functions are accessed

by first pressing the blue 2nd button. The

SCAN button’s second function is scan

add/delete for scan list updating. The sec-

ond function for the SPC button is the

keypad lock feature.

On an M-PA System model radio, six

(6) of the buttons on the keypad are dual-

function buttons. Press and release the

blue 2nd function button to shift keypad

selection to the scan add/delete (SCAN

button), the keypad lock feature (SPC but-

ton), STO, RCL, CLR, or STS buttons.

ADD/DELETE BUTTON

(Scan And System Models Only)

When in trunked mode, pressing and

releasing 2nd and then pressing A/D

(shifted SCAN button) will toggle the se-

lectedgroupon andoff thescan list.When Figure 6 - System Model Keypad

Figure 5 - Scan Model Keypad

Andere Handbücher für M-PA EDACS

Inhaltsverzeichnis

Andere Ericsson Tragbares Radio Handbücher

Ericsson

Ericsson Monorgam MHP 300 Bedienungsanleitung

Ericsson

Ericsson EDACS MTL Bedienungsanleitung

Ericsson

Ericsson EDACS M-RK-II SCAN Bedienungsanleitung

Ericsson

Ericsson LBI-39110 Bedienungsanleitung

Ericsson

Ericsson KPC-300 Bedienungsanleitung

Ericsson

Ericsson MPI-II LBI-38558B Bedienungsanleitung

Ericsson

Ericsson TMX-8825 Bedienungsanleitung

Ericsson

Ericsson PCS Bedienungsanleitung

Ericsson

Ericsson AEGIS EDACS M-PA LBI-33056 Bedienungsanleitung

Ericsson

Ericsson KPC-300 Bedienungsanleitung

Ericsson

Ericsson PCS Bedienungsanleitung

Ericsson

Ericsson LBI-39125A Bedienungsanleitung

Ericsson

Ericsson EDACS M-RK-II Bedienungsanleitung

Ericsson

Ericsson M-PA Bedienungsanleitung

Ericsson

Ericsson DUAL FORMAT MDR Bedienungsanleitung

Ericsson

Ericsson M-PATM SERIES LBI-38377E Bedienungsanleitung

Ericsson

Ericsson MDX SERIES Bedienungsanleitung

Ericsson

Ericsson RRUS 13 Bedienungsanleitung

Ericsson

Ericsson LBI-38823C Bedienungsanleitung

Ericsson

Ericsson EDACS DPE-100 Bedienungsanleitung

Ericsson

Ericsson EDACS DPE-100 Bedienungsanleitung

Ericsson

Ericsson M-PA EDACS Bedienungsanleitung

Ericsson

Ericsson LZT-1872R1A Bedienungsanleitung

Ericsson

Ericsson LBI-38732D Bedienungsanleitung

Beliebte Tragbares Radio Handbücher anderer Marken

Telefunken

Telefunken P5 Bedienungsanleitung

Tait

Tait TP9300 Bedienungsanleitung

Lafayette

Lafayette Guardian 5500 Bedienungsanleitung

Sailor

Sailor SP3300 Bedienungsanleitung

Matra Nortel

Matra Nortel MC 6500 Bedienungsanleitung

Hytera

Hytera PD362i Bedienungsanleitung

Vertex Standard

Vertex Standard VX-P920 Series Bedienungsanleitung

Roberts

Roberts Ecologic 3 Bedienungsanleitung

LENCO

LENCO IPD-5100 Bedienungsanleitung

Baofeng

Baofeng BF-82 Bedienungsanleitung

Trevi

Trevi RA 764 Bedienungsanleitung

M/A-Com

M/A-Com P5100 Series Bedienungsanleitung

Elta

Elta 6699 Bedienungsanleitung

PURE

PURE ONE classic Series II Bedienungsanleitung

Teac

Teac PR130 Bedienungsanleitung

Philips

Philips AE6370 Bedienungsanleitung

Simoco

Simoco SRP9170 Bedienungsanleitung

Audiovox

Audiovox FR14 Bedienungsanleitung