Ericsson M-PA Bedienungsanleitung

Operator’s Manual

AEGIS EDACS®M-PA

SELECT MODEL

PORTABLE RADIO

LBI-38793B

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . 5

CONTROLS . . . . . . . . . . . . . . 5

INDICATORS . . . . . . . . . . . . . . 7

OPERATION . . . . . . . . . . . . . . 10

POWER-UP . . . . . . . . . . . . . 10

VOICE MODES . . . . . . . . . . . 10

Clear Mode . . . . . . . . . . . 10

Aegis Digital Mode . . . . . . . . 10

Aegis Private And Voice Guard

Private Modes (Optional) . . . . 11

TRUNKED MODE OPERATION . . . 13

Receiving A Message . . . . . . 14

Sending A Message . . . . . . . 15

Emergency Operation

(Trunked Mode) . . . . . . . . . 16

Dynamic Regrouping . . . . . . 16

TABLE OF CONTENTS (Cont.)

Wide Area SystemScanning . . 17

Receiving A Message . . . . . . 17

Sending A Message . . . . . . 18

Emergency Operation

(Conventional Mode) . . . . . . 19

OPERATINGTIPS . . . . . . . . . . . 19

OPERATING RULES AND

REGULATIONS . . . . . . . . . . . . 20

BATTERY PACKS . . . . . . . . . . . 21

INSTALLING THEBATTERY PACK . 21

REMOVING THE BATTERY PACK . 21

CHARGING THE BATTERY PACKS . 22

RECHARGEABLE BATTERY PACK

DISPOSAL . . . . . . . . . . . . . 22

SWIVEL MOUNT REMOVAL AND

REPLACEMENT . . . . . . . . . . . 23

INTRINSICALLYSAFE USAGE . . . . 23

GLOSSARY . . . . . . . . . . . . . . 25

WARRANTY . . . . . . . . . . . . . . 30

NICKEL-CADMIUM BATTERY

WARRANTY . . . . . . . . . . . . . . 31

This manual is published by

Ericsson Inc.

, without any war-

ranty. Improvements and changes to this manual necessitated by

typographicalerrors, inaccuraciesofcurrentinformation,or improve-

ments to programs and/or equipment, may be made by

Ericsson

Inc.

, at any time and without notice.Such changes will be incorpor-

tated into new editions of this manual.No part of this manual may be

reproduced or transmitted in any form or by any means, electronic

or mechanical, including photocopying and recording, for any pur-

pose, without the express written permission of

Ericsson Inc.

PRODUCT SPECIFICATION FOR CE

MARKED EQUIPMENT

The M-PA Portable conforms to the following

Product Specifications.

EUROPEAN STANDARDS:

Safety: Not applicable

EMC: prETS 300 279 (August 1995)

TTD: Not applicable

SUPPLEMENTARY INFORMATION

At this time, the M-PA portable radio may not

be operated while in a vehicular charger in the

EuropeanCommunitysinceithasnotbeenevalu-

ated for operation in this mode.

TheM-PAportableradiomay beusedinboth

trunked and conventional applications.

Figure 1 -Aegis EDACSM-PA SystemModel Radio

SIDE VIEW FRONT VIEW

INTRODUCTION

The Aegis



EDACS M-PA



Select model

portable radio is a high-performance two-way ra-

dio that provides clear voice, Aegis digital, and

Aegis private communications.The radio is also

compatible with Voice Guard®communication

systems. Personality programming allows maxi-

mum integration flexibility into EDACS and con-

ventional radio systems.

The radio must be equipped with the en-

crypt/decrypt option before operation in Aegis

private or Voice Guard modes is possible. This

option allows the radio to communicate using

highly secure state-of-the-art Aegis and Voice

Guard encryption and decryption techniques.

Operating controls on the radio include a

rotatable system/group/channel control knob, ro-

tatable volume control, 16-button keypad, push-

to-talk, emergency and monitor buttons. The

on/off power switch for the unit is located on the

removable battery pack.

The8-digitalphanumericliquidcrystaldisplay

(LCD) on the front of the radio displays the oper-

ating status of the radio. This backlit display also

has sixteen status flags that indicate various op-

erating conditions such as private communica-

tions enabled, transmitter on, scanning, or emer-

gency mode enabled.

The exact operation of your radio will vary

depending upon the mode of operation, the ra-

dio’s programming, and the particular radio sys-

tem. Consult your radio system’s representative

for particular features that are programmed into

your radio.

CONTROLS

ON/OFF SWITCH

The ON/OFF SWITCH is located on the bat-

terypack. Slidingthisswitchupwillsupplypower

totheradiofromthebatterypack. Anaudibleclick

will be heard and the "ON" indicator will be ex-

posed. Whentheradioisturnedon,itwillperform

a power-up self test and then resume operation

ontheprevious operatingsystem,grouporchan-

nel as displayed in the LCD. Sliding the switch

down will turn the radio off.

VOLUME CONTROL KNOB

TheVOLUMECONTROLKNOBisarotatable

control on the top of the radio used to adjust the

receiver’saudiolevelinthespeaker. Rotatingthis

knob in a clockwise direction will increase the

audio level. Counter-clockwise rotation will de-

crease the audio level. Minimum levels may be

programmedintotheradiotopreventmissedcalls

due to too low of a volume setting.

CONTROL KNOB

The rotatable 16-position CONTROL KNOB

located on the top of the radio may be pro-

grammed to select trunked groups and conven-

tionalchannelsoritmaybeprogrammedtoselect

systems. SeeSYSTEM/GROUP/CHANNEL SE-

LECTION for details.

A stop plate may be installed under the knob

to limit the maximum number of positions to less

than sixteen (16). It is normally factory installed

for fifteen (15) positions.

PTT BUTTON

PressingthePTTBUTTONontheside ofthe

radio will enable the radio’s transmitter. The "TX"

statusflaginthedisplaywillturnonwhentheradio

is transmitting. Releasing the PTT BUTTON will

return operation to receive mode.

Whenoperatinginatrunkedsystem,theradio

may be programmed to automatically transmit

(withouttheoperatorpressing thePTTBUTTON)

tomaintaincommunicationwiththesitecontroller.

The "TX" statusflag will turn on when theradio is

transmitting.

MONITOR BUTTON

Trunked Mode

When operating in trunked mode, pressing

the MONITOR BUTTON after an individual call

has been received will return the radio to the

groupcallmode. Theradiowillnotrespondonan

individual basis, but will then transmit groupcalls

whenthePTTBUTTONispressed. Theradiowill

also automatically return to the group call mode

after the programmed call-back time-out period

expires.

Pressing the MONITOR BUTTON will also

clear any digits entered from the numeric keypad

andreturntheradiototheselectedgroupdisplay.

In addition, this button is used to toggle be-

tween group and regroup settings if the Dynamic

Regrouping mode (with deselect capability) has

been enabled by the site controller.

Conventional Mode

When the radio is operating in conventional

mode the MONITOR BUTTON is used to un-

squelch the receiver. If programmed for the se-

lected channel, it will also toggle Channel Guard

(CG) and/or Type 99 (T99) signaling on and off.

Momentarily pressing the MONITOR BUT-

TON will unsquelch the receiver. If programmed,

pressing and holding the button for at least one

(1)secondwilltoggleCGand/orT99signalingon

oroff. AfteraT99callhasbeenreceived,pressing

theMONITORBUTTONwillresettheradioforthe

next call. Note: Selecting another channel will

turnCGandT99signalingbackonifprogrammed

for the channel.

EMERGENCY BUTTON

When operating in trunked mode, pressing

and holding the red EMERGENCY BUTTON on

top of the radio for approximately one (1)second

willinitiateanemergencycallwithvoiceoperation

on the programmed home group. If no home

group is programmed into the radio, voice opera-

tion will be on the selected group.

In conventional mode, initiating an emer-

gency call by pressing the EMERGENCY BUT-

TON will cause the radio to transmit GE-STAR

signaling on the programmed emergency chan-

nel. If no emergency channel is programmed,

GE-STAR will be transmitted on the selected

channel.

INDICATORS

The radio’s liquid crystal display (LCD) lo-

cated on the front panel has eight (8) alphanu-

meric characters and sixteen (16) status flags.

This display provides indications of the current

operating system, group or channel and it dis-

playsvariousothermessagessuchasspecialcall

ID names or numbers, and telephone intercon-

nect numbers.

LCDbacklightingwillturnonforashortperiod

anytime an active button is pressed or the CON-

TROL KNOB is rotated. Backlighting may be

programmed to remain off at all times.

Thesixteen(16)statusflagslocatedalongthe

top and bottom of the display indicate operating

modes and conditions as follows:

EMG EMerGency mode - On indicates an

emergency call has been initiated by

the user. Flashing indicates an emer-

gency call has been received.

NC NoControlchannel- Onindicatesthe

radio is not receiving the trunked con-

trol channel. Flashing indicates the

trunkedsystemisinafailsoftcondition

(supervisory radios only).

HI HIgh power transmit - On indicates

the selected system or channel has

been programmed for high power

transmit operation. Off indicates low

power transmit.

MSG MeSsaGe - Flashing indicates an in-

dividual call has been received

(trunked mode).

T99 Type 99 tone decode - On indicates

Type 99 tone decoding is enabled on

the selected conventional channel.

FlashingindicatesaT99 selective call

has been received and the radio must

be reset to receive another T99 call.

CNV CoNVentionalmode-Onindicatesthe

radio is operating in the conventional

mode.

SPC SPecial Call mode - On indicates the

special call mode has been enabled

(trunked mode).

PVT PriVaTe mode - On indicates private

mode is enabled and the radio will

transmit encrypted messages on the

selected group or channel. Flashing

indicatesanencryptedmessageisbe-

ing received.

TX Transmitter enabled - On when the

radio is transmitting.

BSY BuSY - When in trunked mode, on

indicates the radio is receiving a call;

flashing indicates a call has been

queued. In conventional mode,on in-

dicates a carrier is being received.

Figure 2 -Liquid Crystal Display

CG Channel Guard - On indicates Chan-

nel Guard encode/decode is enabled

ontheselectedconventionalchannel.

BAT BATterylow-Onindicatesthe battery

pack’s charge is low.

UNIVERSAL DEVICE CONNECTOR

The Universal Device Connector (UDC) is

locatedonthesideoftheradiojustabovethePTT

and MONITOR BUTTONS. This connector pro-

vides connections for the external accessories

such as a headset, a speaker-mike, or an emer-

gency lanyard. When the radio is locked in a

vehicularcharger/repeater,theUDCprovidesthe

audio and control connections between the radio

and the vehicular charger/repeater. The UDC is

also used by the maintenance personnel when

the radio is programmed.

ALERT TONES

The radio sounds five (5) basic alert tones or

"beeps" to indicate various operating conditions.

Alert tones may be programmed to remain off at

all times.

•500 Hz Tone –trunked failure tone -

sounds when a trunked

failure has occurred (call

denied, failed confirma-

tion).

–lowbattery-soundswhen

the battery pack’s charge

is low.

•800 Hz Tone –private mode disabled -

on a conventional chan-

nel,soundswhenthePTT

BUTTON is pressedif pri-

vate transmit mode has

previously been disabled.

•1000 Hz Tone –alert tone - sounds when

a button is pressed and a

status change occurs

–channel access tone -

sounds when a trunked

channel has been as-

signed and it is clear to

talk.

•1200 Hz Tone –private mode channel ac-

cess tone - sounds when

the radio is in the private

transmit mode, a trunked

channel has been as-

signed and it is clear to

talk.

•2500 Hz Tone –call queued tone-sounds

when a trunked call is

queued.

OPERATION

POWER-UP

Afterthebatterypackandantennahavebeen

installed, turn the radio on by sliding theON/OFF

SWITCH on the battery pack up. After the radio

has completed a power-up self-test, it will begin

operationonthelastoperating stateasdisplayed

intheLCD. Ifprogrammedon,thepower-upalert

tone (beep) will be heard.

If the radio was previously operating in a

trunkingsystemandcommunicationwiththissys-

tem’s control channel cannot be established, the

"NC"statusflagwillturnon. Thismayoccurif,for

example, the radio is out of range of the previous

trunking site. It may be necessary move to an-

other location, select another trunking system, or

a conventional channel.

VOICE MODES

Each system (trunked or conventional) in the

radio is programmed for either Aegis or Voice

Guard communications.Aegis programmed sys-

tems have three (3) different voice modes:clear,

digitalandprivate.VoiceGuardsystemshavetwo

(2) voice modes: clear and private. The voice

modes are programmed on a per-group basis

withineachtrunkedsystemandonaper-channel

basis within each conventional system. A radio

mustbeequippedwiththeencrypt/decryptoption

before it will operate in Aegis private or Voice

Guard modes.

Clear Mode

AegisclearandVoiceGuardclearmodesare

identicalvoicemodesinwhichtheradiotransmits

and receives only clear (analog) voice signals.

These analog signals are non-digitized and non-

encrypted.Clearmodetransmissionscanbeeas-

ily monitored by unauthorized persons. Groups

and channels programmed for clear operation

cannot transmit or receive Aegis digital or private

messages.

Aegis Digital Mode

Aegisdigitalmodeallowstheradiototransmit

and receive digitized voice signals. Aegis digital

signals provide improved weak signal perform-

ance and they cannot be easily monitored with a

Andere Handbücher für M-PA

Inhaltsverzeichnis

Andere Ericsson Tragbares Radio Handbücher

Ericsson

Ericsson Monogram Series Bedienungsanleitung

Ericsson

Ericsson LBI-39110 Bedienungsanleitung

Ericsson

Ericsson LZT-1872R1A Bedienungsanleitung

Ericsson

Ericsson LBI-38823C Bedienungsanleitung

Ericsson

Ericsson LBI-38732D Bedienungsanleitung

Ericsson

Ericsson PCS Bedienungsanleitung

Ericsson

Ericsson PCS Bedienungsanleitung

Ericsson

Ericsson EDACS DPE-100 Bedienungsanleitung

Ericsson

Ericsson PCS Bedienungsanleitung

Ericsson

Ericsson PCS Bedienungsanleitung

Ericsson

Ericsson KPC-300 Bedienungsanleitung

Ericsson

Ericsson KPC-300 Bedienungsanleitung

Ericsson

Ericsson EDACS M-RK-II Bedienungsanleitung

Ericsson

Ericsson AEGIS M-PA Bedienungsanleitung

Ericsson

Ericsson EDACS DPE-100 Bedienungsanleitung

Ericsson

Ericsson M-PATM SERIES LBI-38377E Bedienungsanleitung

Ericsson

Ericsson Voice Guard M-Pa SCAN Bedienungsanleitung

Ericsson

Ericsson TMX-8825 Bedienungsanleitung

Ericsson

Ericsson LBI-38795B Bedienungsanleitung

Ericsson

Ericsson M-PA EDACS Bedienungsanleitung

Ericsson

Ericsson DUAL FORMAT MDR Bedienungsanleitung

Ericsson

Ericsson LBI-38836A Bedienungsanleitung

Ericsson

Ericsson DUAL FORMAT MDR Bedienungsanleitung

Ericsson

Ericsson Monogram Series Bedienungsanleitung

Beliebte Tragbares Radio Handbücher anderer Marken

Telefunken

Telefunken P5 Bedienungsanleitung

Tait

Tait TP9300 Bedienungsanleitung

Lafayette

Lafayette Guardian 5500 Bedienungsanleitung

Sailor

Sailor SP3300 Bedienungsanleitung

Matra Nortel

Matra Nortel MC 6500 Bedienungsanleitung

Hytera

Hytera PD362i Bedienungsanleitung

Vertex Standard

Vertex Standard VX-P920 Series Bedienungsanleitung

Roberts

Roberts Ecologic 3 Bedienungsanleitung

LENCO

LENCO IPD-5100 Bedienungsanleitung

Baofeng

Baofeng BF-82 Bedienungsanleitung

Trevi

Trevi RA 764 Bedienungsanleitung

M/A-Com

M/A-Com P5100 Series Bedienungsanleitung

Elta

Elta 6699 Bedienungsanleitung

PURE

PURE ONE classic Series II Bedienungsanleitung

Teac

Teac PR130 Bedienungsanleitung

Philips

Philips AE6370 Bedienungsanleitung

Simoco

Simoco SRP9170 Bedienungsanleitung

Audiovox

Audiovox FR14 Bedienungsanleitung