Ericsson Voice Guard M-Pa SCAN Bedienungsanleitung

M-PASCAN MODEL

PORTABLE RADIO

(VGE ALGORITHM)

LBI-38690A

Operator’s Manual

TABLE OF CONTENTS

Page

INTRODUCTION . . . . . . 4

CONTROLS . . . . . . . . 5

ON/OFF SWITCH . . . . 5

VOLUME CONTROL

KNOB . . . . . . . . . . . 5

CONTROL KNOB . . . . 5

PTT BUTTON . . . . . . 5

MONITOR BUTTON . . . 7

EMERGENCY BUTTON . 7

MENU BUTTON . . . . . 7

PRIVATE BUTTON . . . . 8

TABLE OF CONTENTS - Cont.

Page

EXIT BUTTON . . . . . . . 9

SCAN BUTTON . . . . . . 9

SELECT BUTTON . . . . . 9

INDICATORS . . . . . . . . . 10

UNIVERSAL DEVICE

CONNECTOR . . . . . . . . 12

ALERT TONES . . . . . . . . 12

CARRIER CONTROL

TIMER . . . . . . . . . . . 12

CHANNEL BUSY . . . . . 13

RECEIVE ONLY

CHANNEL . . . . . . . . . 13

VOICE GUARD

DISABLED . . . . . . . . . 13

RADIO/CHANNEL

FAILURE . . . . . . . . . . 13

OPERATION . . . . . . . . . 13

POWER-UP . . . . . . . . 13

MODE/CHANNEL/CG

SELECTION . . . . . . . . 14

This manual is published by Ericsson Inc., without any

warranty. Improvements and changes to this manual ne-

cessitated by typographical errors, inaccuracies of cur-

rent information, or improvements to programs and/or

equipment, may be made by Ericsson Inc., at any time

and without notice. Such changes will be incorporated

into new editions of this manual. No part of this manual

may be reproduced or transmitted in any form or by any

means, electronic or mechanical, including photocopying

and recording, for any purpose, without the express writ-

ten permission of Ericsson Inc.

TABLE OF CONTENTS - Cont.

Page

CRYPTOGRAPHIC

KEYHANDLING . . . . . 15

RECEIVING A

MESSAGE . . . . . . . . 17

TRANSMITTING A

MESSAGE . . . . . . . . 18

EMERGENCY

OPERATION . . . . . . . 20

SCANNING

CHANNELS . . . . . . . 20

Using Scan . . . . . . . . 22

TELEPHONE

INTERCONNECT

CALLS . . . . . . . . . . 23

"KEYLOCK" MENU . . . 24

"ALERT" MENU . . . . . 25

OPERATING TIPS . . . . . 25

OPERATING RULES AND

REGULATIONS . . . . . . . 26

BATTERY PACKS . . . . . . 28

INSTALLING THE

BATTERY PACK . . . . . 28

TABLE OF CONTENTS - Cont.

Page

REMOVING THE

BATTERY PACK . . . . . . 28

CHARGING THE

BATTERY PACKS . . . . . 28

RECHARGEABLE BATTERY

PACK DISPOSAL . . . . . 30

SWIVEL MOUNT REMOVAL AND

REPLACEMENT . . . . . . . 30

INTRINSICALLY SAFE

USAGE . . . . . . . . . . . . 30

BATTERY PACKS . . . . . 31

ACCESSORIES . . . . . . 31

GLOSSARY . . . . . . . . . 32

WARRANTY . . . . . . . . . 38

NICKEL-CADMIUM BATTERY

WARRANTY . . . . . . . . . 39

INTRODUCTION

This manual describes the opera-

tion of the M-PAVoice Guard®Scan

model radio. This full-featured portable

radio provides Voice Guard two-way

communications using the VGE algo-

rithm. The M-PA Voice Guard radio pro-

vides full-range performance for private

(guarded) and clear communications.

The cryptographic key in the radio

provides the encryption and decryption

code necessary for private communica-

tions.Only radios with the same crypto-

graphic key can monitor and

communicate. Cryptographic keys are

transferred into the radio using VGE

Keyloader, Option V4028. VGE

equipped Voice Guard radios must also

be programmed with identical CUE

(Customer Unique Encryption) code(s)

before private communications are pos-

sible. CUE codes are programmed into

the radio along with the overall person-

ality information using an IBM PC or

compatible computer.

Operating controls on the radio in-

clude a rotatable control knob, rotatable

volume control, 4-button keypad, push-

to-talk, emergency and monitor buttons.

The on/off power switch for the unit is

located on the removable battery pack.

The 8-digit alphanumeric liquid

crystal display (LCD) on the front of the

radio displays the operating status of

the radio. This backlit display also has

twelve status flags that indicate various

operating conditions such as private

communications enabled, transmitter

on, scanning, or emergency mode en-

abled.

The exact operation of your radio

will vary depending upon the mode of

operation, the radio’s programming, and

the particular radio system. Consult

your radio system’s representative for

particular features that are programmed

into your radio.

CONTROLS

ON/OFF SWITCH

The ON/OFF SWITCH is located

on the battery pack. Sliding this switch

up will supply power to the radio from

the battery pack. An audible click will be

heard and the "ON" indicator will be ex-

posed. When the radio is turned on, it

will perform a power-up self test and

then resume operation on the previous

operating channel as displayed in the

LCD. Sliding the switch down will turn

the radio off

VOLUME CONTROL KNOB

The VOLUME CONTROL KNOB is

a rotatable control on the top of the ra-

dio used to adjust the receiver’s audio

level in the speaker. Rotating this knob

in a clockwise direction will increase the

audio level. Counter-clockwise rotation

will decrease the audio level Minimum

levels may be programmed into the ra-

dio to prevent missed calls due to too

low of a volume setting.

CONTROL KNOB

The rotatable 16-position CON-

TROL KNOB located on the top of the

radio is programmed to select the oper-

ating channel, mode, or specific Chan-

nel Guard encode/decode tones. See

MODE/CHANNEL/CG SELECTION for

details. A stop plate may be installed

under the knob to limit the maximum

number of positions to less than sixteen

(16). It is normally factory installed for

fifteen (15) positions. Some radios may

be programmed with this knob disabled.

PTT BUTTON

Pressing the PTT BUTTON on the

side of the radio will enable the radio’s

transmitter. The "TX" status flag in the

display will turn on when the radio is

Figure 1 - M-PA Scan Model Radio

transmitting. Releasing the PTT BUT-

TON will return operator to receive

mode.

MONITOR BUTTON

The MONITOR BUTTON is used to

unsquelch the receiver. Momentarily

pressing this button will disable squelch

and the receiver noise will be heard in

the speaker.

If programmed enabled for the se-

lected channel, Channel Guard (CG)

and/or Type 99 (T99) signaling will be

enabled when the channel is selected.if

CG and/or T99 are enabled, the appro-

priate status flag "CG" and/or "T99" will

turn on. The MONITOR BUTTON may

then be used to toggle CG and/or T99

between disabled and enabled by

pressing and holding it for at least one

(1) second; the appropriate status flag

will toggle on or off The MONITOR

BUTTON is also used to reset T99 op-

eration after a call is received.

EMERGENCY BUTTON

The EMERGENCY BUTTON is the

small red button located on top of the

radio near the antenna. If this button is

programmed for emergency operation,

pressing it for at least one (1) second

will cause the radio to transmit GE-

STAR emergency signaling. The "EMG"

status flag will turn on. GE-STAR is

transmitted according to one of several

different programmable methods. See

EMERGENCY OPERATION for de-

tails.

This button may also be pro-

grammed as a home mode button. if

programmed in this manner; pressing it

will switch operation to the programmed

home mode.

MENU BUTTON

Pressing the MENU button causes

the radio to scroll through up to six (6)

different menus programmed into the

radio. After the desired menu is dis-

played, the feature within the menu is

selected with the SEL button. The

menus that may be programmed are:

Menu Display Function Or Use

"CHANNEL" The MENU and SEL

buttons are programmed

for channel selection.

When this display ap-

pears, select the desired

channel with the SEL

button and then press

EXIT.

"MODE" The MENU and SEL

buttons are programmed

for mode selection.

When this display ap-

pears, select the desired

mode by pressing the

SEL button and then

press EXIT.

"PHONE" Allows selection of one

(1) of the ten (10) pro-

grammed telephone

numbers for automatic

dialing.

"KEYLOCK" Allows the keypad but-

tons to be locked or un-

locked.

"SCAN A/D" Allows channels to be

added to or deleted from

the scan list for the cur-

rent mode. The priority-

one channel and the

priority-two channel are

also set within this

menu.

"ALERT" Allows the alert tones to

be disabled or enabled.

PRIVATE BUTTON

Private transmit mode is enabled or

disabled by pressing and releasing the

PVT button (when the menu mode is

not selected). When private transmit

mode is enabled, the "PVT" status flag

in the display will turn on.

If the radio is programmed for

forced private operation and the se-

lected channel is programmed for pri-

vate operation, "FRCD PVT" will be

displayed when PVT is pressed; private

transmit mode is not disabled. If the ra-

dio is programmed for forced private op-

eration and the selected channel is not

programmed for private operation, "VG

DISBL" will momentarily show in the

display when PVT is pressed; the radio

will not change to private mode.

EXIT BUTTON

Pressing the EXIT button will cause

the radio to exit the current menu dis-

play and return operation to the channel

currently selected. If the menu mode is

not enabled when the button is pressed,

pressing this button will turn the display

and keypad backlighting on for thirty

(30) seconds (if the backlight is pro-

grammed on).

SCAN BUTTON

Pressing the SCAN button on the

keypad will toggle scan operation on

and off. When the radio is scanning, the

"SCN" status flag in the display will

show and all channels on the scan list

will be scanned. See SCANNING

CHANNELS for additional details.

SELECT BUTTON

Selecting different features within

each menu is accomplished with the

SEL button. First, the menu mode must

Figure 2 - MPA Scan Model Keypad

be enabled and the desired menu must

be chosen by pressing and releasing

the MENU button until the desired

menu appears in the display After the

menu is chosen, the desired function or

feature is selected by pressing the SEL

button. For example, to disable or en-

able the alert tones, press MENU until

"ALERT" is displayed then press SEL to

select "ENABLED"or "DISABLED", as

desired. Next press the EXIT button.

INDICATORS

The radio’s liquid crystal display

(LCD) located on the front panel has

eight (8) alphanumeric characters and

twelve (12) status flags. This display in-

dicates the current operating channel

and it displays the menu information

when this mode is enabled. It also dis-

plays various other messages.

LCD backlighting will turn on for a

short period anytime an active button is

pressed or the CONTROL KNOB is ro-

tated. Backlighting may be programmed

to remain off at all times. Pressing the

EXIT button when the menu mode is

not enabled, will turn display and key-

pad backlighting on for thirty (30) sec-

onds (if backlight programming is on).

The twelve (12) status flags located

along the top and bottom of the display

indicate operating status as follows:

EMG EMerGency mode - On indi-

cates emergency GE-STAR sig-

naling has been initiated by the

user.

HI HIgh power transmit - On indi-

cates the selected channel has

Figure 3 - Liquid Crystal Display

Inhaltsverzeichnis

Andere Ericsson Tragbares Radio Handbücher

Ericsson

Ericsson DUAL FORMAT MDR Bedienungsanleitung

Ericsson

Ericsson M-PA SELECT Bedienungsanleitung

Ericsson

Ericsson LBI-38795B Bedienungsanleitung

Ericsson

Ericsson LBI-39125A Bedienungsanleitung

Ericsson

Ericsson PCS Bedienungsanleitung

Ericsson

Ericsson EDACS M-RK I Bedienungsanleitung

Ericsson

Ericsson M-PA EDACS Bedienungsanleitung

Ericsson

Ericsson M-PA EDACS Bedienungsanleitung

Ericsson

Ericsson EDACS M-RK-II Bedienungsanleitung

Ericsson

Ericsson KPC-300 Bedienungsanleitung

Ericsson

Ericsson AEGIS M-PA Bedienungsanleitung

Ericsson

Ericsson EDACS M-RK-II SCAN Bedienungsanleitung

Ericsson

Ericsson LBI-38823C Bedienungsanleitung

Ericsson

Ericsson Monogram Series Bedienungsanleitung

Ericsson

Ericsson KPC-300 Betriebsanleitung

Ericsson

Ericsson MDR GE-MARC Bedienungsanleitung

Ericsson

Ericsson KPC-300 Bedienungsanleitung

Ericsson

Ericsson LBI-38732E Bedienungsanleitung

Ericsson

Ericsson Monorgam MHP 300 Bedienungsanleitung

Ericsson

Ericsson GE-MARC VE MDR Bedienungsanleitung

Ericsson

Ericsson AEGIS EDACS M-PA LBI-33056 Bedienungsanleitung

Ericsson

Ericsson Monogram Series MGP 450 Bedienungsanleitung

Ericsson

Ericsson EDACS IPE SERIES Bedienungsanleitung

Ericsson

Ericsson EDACS IPE-200 Bedienungsanleitung

Beliebte Tragbares Radio Handbücher anderer Marken

Telefunken

Telefunken P5 Bedienungsanleitung

Tait

Tait TP9300 Bedienungsanleitung

Lafayette

Lafayette Guardian 5500 Bedienungsanleitung

Sailor

Sailor SP3300 Bedienungsanleitung

Matra Nortel

Matra Nortel MC 6500 Bedienungsanleitung

Hytera

Hytera PD362i Bedienungsanleitung

Vertex Standard

Vertex Standard VX-P920 Series Bedienungsanleitung

Roberts

Roberts Ecologic 3 Bedienungsanleitung

LENCO

LENCO IPD-5100 Bedienungsanleitung

Baofeng

Baofeng BF-82 Bedienungsanleitung

Trevi

Trevi RA 764 Bedienungsanleitung

M/A-Com

M/A-Com P5100 Series Bedienungsanleitung

Elta

Elta 6699 Bedienungsanleitung

PURE

PURE ONE classic Series II Bedienungsanleitung

Teac

Teac PR130 Bedienungsanleitung

Philips

Philips AE6370 Bedienungsanleitung

Simoco

Simoco SRP9170 Bedienungsanleitung

Audiovox

Audiovox FR14 Bedienungsanleitung