ESAB Caddy Tig 1500i VRD Bedienungsanleitung

Caddy®

Instruction manual

0460 826 374 GB 20190125

Valid for: serial no. Tig 1500i: 711-, 747-, 840-xxx-xxxx,

Tig2200i:747-xxx-xxxx

Tig 1500i VRD 

Tig2200iVRD

TABLE OF CONTENTS

0460 826 374 © ESAB AB 2019

1SAFETY ....................................................................................................... 4

1.1 Meaning of symbols ............................................................................... 4

1.2 Safety precautions ................................................................................. 4

2INTRODUCTION.......................................................................................... 7

2.1 Equipment ............................................................................................... 7

2.2 Control panels ........................................................................................ 7

3TECHNICAL DATA ...................................................................................... 8

4INSTALLATION............................................................................................ 10

4.1 Location................................................................................................... 10

4.2 Mains power supply ............................................................................... 10

5OPERATION ................................................................................................ 12

5.1 Connections and control devices ......................................................... 12

5.2 Key to symbols....................................................................................... 12

5.3 TIG (GTAW)-welding ............................................................................... 12

5.4 MMA (SMAW)-welding............................................................................ 13

5.5 Overheating protection .......................................................................... 13

5.6 Connection to cooling unit (only valid for Tig 2200i).......................... 13

5.7 Turning on the power source ................................................................ 13

6MAINTENANCE........................................................................................... 14

6.1 Inspection and cleaning......................................................................... 14

7TROUBLESHOOTING ................................................................................. 15

8ORDERING SPARE PARTS ........................................................................ 16

DIAGRAM ............................................................................................................ 17

ORDERING NUMBERS....................................................................................... 23

ACCESSORIES ................................................................................................... 24

Rights reserved to alter specifications without notice.

1 SAFETY

0460 826 374 -4- © ESAB AB 2019

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and

Safety Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0460 826 374 -5- © ESAB AB 2019

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or work

cable around your body. Keep welding power source and cables as

far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0460 826 374 -6- © ESAB AB 2019

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be

potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations,

due to conducted as well as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on

Waste Electrical and Electronic Equipment and its

implementation in accordance with national law,

electrical and/or electronic equipment that has reached

the end of its life must be disposed of at a recycling

facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved

collection stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0460 826 374 -7- © ESAB AB 2019

2 INTRODUCTION

The Tig 1500i / 2200i is a TIG (GTAW) welding power source, which can also be used for

MMA (SMAW) welding. It supplies direct current (DC).

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

2.1 Equipment

The power source is supplied with a 3 m (9.84ft) welding cable complete with a TIG-torch,

3m(9.84ft) return cable, 3 m (9.84 ft) mains cable, instruction manual for power source and

control panel, see Ordering information in the "ORDERING NUMBERS" chapter.

2.2 Control panels

TA33 TA34

See the separate instruction manual for a detailed description of the control panels.

3 TECHNICAL DATA

0460 826 374 -8- © ESAB AB 2019

3 TECHNICAL DATA

Tig 1500i Tig 2200i

Mains voltage 230V, ±10%, 1~ 50/60 Hz 230V, ±10%, 1~ 50/60 Hz

Mains supply Zmax 0.35 ohm Zmax 0.31 ohm

Primary current

ImaxTIG 14 A 25 A

ImaxMMA 22 A 26 A

No-load power demand when

in the energy-saving mode,

6.5 min. after welding

30 W 31 W

Setting range

TIG (GTAW) 3 A - 150 A 3 A - 220 A

MMA (SMAW) 4 A - 150 A 4 A - 170 A

Ignition voltage (Upk) 11.5 kV 11.5 kV

Permissible load at TIG (GTAW)

20% duty cycle 220 A / 18.8 V

25% duty cycle 150 A / 16.0 V

60% duty cycle 120 A / 14.8 V 150 A / 16.0 V

100% duty cycle 110 A / 14.4 V 140 A / 15.6 V

Permissible load at MMA (SMAW)

25% duty cycle 150 A / 26.0 V 170 A / 26.8 V

60% duty cycle 100 A / 24.0 V 130 A / 25.2 V

100% duty cycle 90 A / 23.6 V 110 A / 24.4 V

Power factor at maximum current

TIG (GTAW) 0.98 0.99

MMA (SMAW) 0.99 0.99

Efficiency at maximum current

TIG (GTAW) 77 % 73.0 %

MMA (SMAW) 80 % 77.9 %

Apparent powerat maximum

current

5.9kVA

Active powerat maximum

current

5.9kW

Open-circuit voltage TIG

(GTAW)

55-60 V 55-60 V

Open-circuit voltage MMA

(SMAW)

55-60 V 55-60 V

with VRD < 35 V < 35 V

No-load voltage

without VRD, U056V

with VRD, Ur22V

3 TECHNICAL DATA

0460 826 374 -9- © ESAB AB 2019

Tig 1500i Tig 2200i

Upk(with arc ignition unit, Tig) 10.7kV

Operating temperature -10 to + 40 °C

(+14to+104°F)

-10 to + 40 °C

(+14to+104°F)

Transportation temperature -20 to + 55 °C (-4 to + 131 °F) -20 to + 55 °C (-4 to + 131 °F)

Constant sound pressure in

open-circuit

< 70 dB (A) < 70 dB (A)

Dimensions, l × b × h 418 × 188 × 208 mm

(16.46×7.40 × 8.19 in.)

418 × 188 × 208 mm

(16.46×7.40 × 8.19 in.)

Dimensions, l × b × h

(including cooling unit)

418 × 188 × 345 mm

(16.46×7.40 × 13.58 in.)

Weight 9.2 kg (20.28 lb) Including cooling unit: 14 kg

(30.86 lb)

Including cooling unit, in

delivery mode: 19.4 kg (42.77

lb)

Shielding gas      

    

max pressure

All types intended for TIG

(GTAW) welding

5 bar (72.5 psi)

All types intended for TIG

(GTAW) welding

5 bar (72.5 psi)

Insulation class transformer H H

Enclosure class IP 23 IP 23

Application class

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or

cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

Mains supply, Zmax

Maximum permissible line impedance of the network in accordance with IEC 61000-3-11.

4 INSTALLATION

0460 826 374 - 10 - © ESAB AB 2019

4 INSTALLATION

The installation must be carried out by a professional.

NOTE!

Mains supply requirements

This equipment complies with IEC 61000-3-12 provided that the short-circuit power

is greater than or equal to Sscmin at the interface point between the user's supply

and the public system. It is the responsibility of the installer or user of the equipment

to ensure, by consultation with the distribution network operator if necessary, that

the equipment is connected only to a supply with a short-circuit power greater than

or equal to Sscmin. Refer to the technical data in the TECHNICAL DATA chapter.

4.1 Location

Position the welding power source such that its cooling air inlets and outlets are not

obstructed.

4.2 Mains power supply

Check that the welding power source is connected to the

correct mains power supply voltage, and that it is protected by

the correct fuse size.

A protective earth connection must be made in accordance with

regulations.



Rating plate with supply connection data

Recommended fuse sizes and minimum cable area

Tig 1500i Tig 2200i

TIG (GTAW) MMA (SMAW) TIG (GTAW) MMA (SMAW)

Mains voltage 230 V ± 10%, 1~ 230 V ± 10%, 1~ 230 V ± 10%, 1~ 230 V ± 10%, 1~

Mains frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz

Mains cable area

mm2

3G2.5 3G2.5 3G2.5 3G2.5

Phase current I1eff 9 A 11 A 11 A 14 A

Fuse

anti-surge 16 A 16 A 16 A 16 A

type C MCB 13 A 13 A 16 A 16 A

Andere Handbücher für Caddy Tig 1500i VRD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Origo Mig 320 Bedienungsanleitung

ESAB

ESAB Renegade ET 180iP Bedienungsanleitung

ESAB

ESAB LAF 631 Bedienungsanleitung

ESAB

ESAB Aristo Arc 4000i Bedienungsanleitung

ESAB

ESAB Migmaster 280 Pro Bedienungsanleitung

ESAB

ESAB Caddy Arc 201i Bedienungsanleitung

ESAB

ESAB Aristo 300 Bedienungsanleitung

ESAB

ESAB LPH 120 Bedienungsanleitung

ESAB

ESAB Fabricator ET 410iP Bedienungsanleitung

ESAB

ESAB Fabricator 181i Bedienungsanleitung

ESAB

ESAB ARC250i Bedienungsanleitung

ESAB

ESAB LUA 400 Bedienungsanleitung

ESAB

ESAB LTR 160 Bedienungsanleitung

ESAB

ESAB DTE 255 Bedienungsanleitung

ESAB

ESAB Rogue ES 150i Bedienungsanleitung

ESAB

ESAB PCM-1125 Bedienungsanleitung

ESAB

ESAB HandyPlasma 250 Bedienungsanleitung

ESAB

ESAB LHJ 425 Bedienungsanleitung

ESAB

ESAB Rogue ES 180i Pro Bedienungsanleitung

ESAB

ESAB Origo Feed 304N P4 Bedienungsanleitung

ESAB

ESAB LKA 180 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

ESAB

ESAB Firepower MST-200 Bedienungsanleitung

ESAB

ESAB RobustFeed AVS Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung