ESAB LAF 631 Bedienungsanleitung

Instruction manual

0449 501 201 GB 20181228 Valid for: serial no. 744-xxx-xxxx

LAF 631

TABLE OF CONTENTS

0449 501 201 © ESAB AB 2018

1SAFETY ....................................................................................................... 4

1.1 Meaning of symbols ............................................................................... 4

1.2 Safety precautions ................................................................................. 4

2INTRODUCTION.......................................................................................... 7

3TECHNICAL DATA ...................................................................................... 8

4INSTALLATION............................................................................................ 10

4.1 Location................................................................................................... 10

4.2 Connections............................................................................................ 11

5OPERATION ................................................................................................ 13

5.1 Controls................................................................................................... 13

6MAINTENANCE........................................................................................... 14

6.1 Cleaning .................................................................................................. 14

6.1.1 Welding power source.......................................................................... 14

6.1.2 Contactor.............................................................................................. 14

7ORDERING SPARE PARTS ........................................................................ 15

DIAGRAM ............................................................................................................ 16

CONNECTION INSTRUCTION............................................................................ 18

ORDERING NUMBERS....................................................................................... 19

Rights reserved to alter specifications without notice.

1 SAFETY

0449 501 201 -4- © ESAB AB 2018

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and

Safety Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0449 501 201 -5- © ESAB AB 2018

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or work

cable around your body. Keep welding power source and cables as

far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0449 501 201 -6- © ESAB AB 2018

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be

potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations,

due to conducted as well as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on

Waste Electrical and Electronic Equipment and its

implementation in accordance with national law,

electrical and/or electronic equipment that has reached

the end of its life must be disposed of at a recycling

facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved

collection stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0449 501 201 -7- © ESAB AB 2018

2 INTRODUCTION

LAF 631 is a remote-controlled 3-phase welding power source designed for high-efficiency

mechanical gas metal arc welding (MIG/MAG) or sub arc welding (SAW).

The welding power source is fan-cooled and is monitored by a thermal cutout against

overload. When the thermal cutout is deployed the yellow lamp on the front panel illuminates

automatically. The reset is carried out automatically when the temperature has decreased to

a permitted level.

The welding power sources and the control unit are linked together over a 2-wire bus

enabling precision control of the welding process.

All welding parameter settings for the power source can be made by the operator on the front

panel of the control unit.

The operation of the power source is completely controlled and monitored by this unit. Even

the start and stop qualities can be set by way of the control unit. The preset welding current

parameters can also be monitored in the course of welding.

3 TECHNICAL DATA

0449 501 201 -8- © ESAB AB 2018

3 TECHNICAL DATA

LAF 631

Mains connection 380/400/415 V 3~50 Hz

440 V 3~60 Hz

Primary current Imax :

SAW 69 A

MIG 69 A

Values of the conventional load:

SAW (duty cycle at 40 °C ambient temperature)

60% 800 A, 44 V

100% 630 A, 44 V

MIG (duty cycle at 40 °C ambient temperature)

60% 800 A, 44 V

100% 630 A, 44 V

Setting range:

SAW 60A/22V–800A/44V

MIG 75A/18V–800A/44V

No-load voltage (U0)56 V

No-load power 172 W

Efficiency at max current (I2):

SAW 84%

MIG 84%

Power factor at max current (I2):

SAW 0.91

MIG 0.91

Apparent power at max current (I2)46.4 kVA

Active power at max current (I2)42 kW

Ssc min (MVA) 5.6 MVA

Working temperature -10 °C to +40 °C

Continual sound pressure at no-load <70 dB(A)

Weight (in delivery mode) 260 kg

Dimensions L × W × H 652 × 483 × 800 mm

652 × 483 × 916 mm (including foot)

Insulation class (transformer) H

Enclosure class IP 23

Application class

Restrictive use Class A

3 TECHNICAL DATA

0449 501 201 -9- © ESAB AB 2018

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

0449 501 201 - 10 - © ESAB AB 2018

4 INSTALLATION

The installation must be carried out by a professional.

NOTE!

Mains supply requirements

This equipment complies with IEC 61000-3-12 provided that the short-circuit power

is greater than or equal to Sscmin at the interface point between the user's supply

and the public system. It is the responsibility of the installer or user of the equipment

to ensure, by consultation with the distribution network operator if necessary, that

the equipment is connected only to a supply with a short-circuit power greater than

or equal to Sscmin. Refer to the technical data in the TECHNICAL DATA chapter.

4.1 Location

WARNING!

Secure the equipment - particularly

if the ground is uneven or sloping.

• Fit the supports supplied. Place the welding power source in such a way that the

cooling air intake and outlet remain free.

Lifting instructions

Andere Handbücher für LAF 631

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Caddy Tig 1500i TA34 Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

ESAB

ESAB Warrior 500 Bedienungsanleitung

ESAB

ESAB Precision Plasmarc Betriebsanleitung

ESAB

ESAB THERMAL DINAMICS CUTMASTER 60i Bedienungsanleitung

ESAB

ESAB LHJ 750 Bedienungsanleitung

ESAB

ESAB m3 Plasma EPP-202 Bedienungsanleitung

ESAB

ESAB EPP-200 Bedienungsanleitung

ESAB

ESAB Origo Mig C151 Bedienungsanleitung

ESAB

ESAB Aristo Tig 4000iw Bedienungsanleitung

ESAB

ESAB PCM-875A Bedienungsanleitung

ESAB

ESAB Warrior YardFeed 200 Bedienungsanleitung

ESAB

ESAB LPH 80 Bedienungsanleitung

ESAB

ESAB A2SF J1 Bedienungsanleitung

ESAB

ESAB LTR 160 Bedienungsanleitung

ESAB

ESAB ESABMig C280 Bedienungsanleitung

ESAB

ESAB PLASMAWELD 202 Bedienungsanleitung

ESAB

ESAB Origo Mig 410 Bedienungsanleitung

ESAB

ESAB MEK 4 Bedienungsanleitung

ESAB

ESAB LKA 150 Bedienungsanleitung

ESAB

ESAB Aristotig 405 AC/DC Bedienungsanleitung

ESAB

ESAB CaddyTig HF Bedienungsanleitung

ESAB

ESAB Fabricator EM 401i Bedienungsanleitung

ESAB

ESAB Caddy Arc 201i Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung