ESAB LHF 400 Bedienungsanleitung

Valid for serial no. 318, 318, 3290349 301 080 070108

LHF 400, LHF 630

LHF 800

Instruction manual

ENGLISH

-- 2 --

TOCe

1 DIREC IVE 3........................................................

2 SAFE Y 3...........................................................

3 IN RODUC ION 5...................................................

4 ECHNICALDA A 5.................................................

5 INS ALLA ION 6....................................................

5.1 Connectingtomains 6.......................................................

6 OPERA ION 7.......................................................

6.1 Controlsandconnections 7...................................................

7 MAIN ENANCE 8....................................................

8 ORDERINGOFSPAREPAR S 8......................................

ASSEMBLYINS RUC IONS 9...........................................

DIAGRAM 12............................................................

-- 3 --

bh10d1 e

1 DIREC IVE

DECLARA ION OF CONFORMI Y

ESAB Welding Equipment AB, S--695 81 Laxå, Sweden, gives its unreserved guarantee that welding

power source LHF 400 / LHF 6 0 / LHF 800 from serial number 18/ 18/ 29 complies with standard

IEC/EN 60974--1, in accordance with the requirements of directive (7 /2 /EEC) and addendum

(9 /68/EEC) and with standard EN 60974--10 in accordance with the requirements of directive

(89/ 6/EEC) and addendum (9 /68/EEC).

--------------------------------------------------------------------------------------------------------------------------------------

Henry Selenius

Vice President

ESAB Welding Equipment AB

695 81 LAXÅ

SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924

Laxå 1.08.2005

2 SAFE Y

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorised person is stationed within the working area of the equipment when it is

started up.

Sno--one is unprotected when the arc is struck

. The workplace must:

Sbe suitable for the purpose

Sbe free from draughts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

-- 4 --

bh10d1 e

WARNING!

Read and understand the instruction manual

before installing or operating.

WARNING

READ AND UNDERS AND HE INS RUC ION MANUAL BEFORE INS ALLING OR OPERA ING.

ARC WELDING AND CU ING CAN BE INJURIOUS O YOURSELF AND O HERS. AKE PRECAU-

IONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFE Y PRAC ICES WHICH SHOULD BE

BASED ON MANUFAC URERS’ HAZARD DA A.

ELEC RIC SHOCK -- Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNC ION -- Call for expert assistance in the event of malfunction.

PRO EC YOURSELF AND O HERS!

ESAB can provide you with all necessary welding protection and accessories.

Do not use the power source for thawing frozen pipes.

WARNING!

his product is solely intended for arc welding.

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human health!

-- 5 --

bh10d1 e

3 IN RODUC ION

LHF 400/630/800 are thyristor controlled welding rectifiers designed for welding with

coated electrodes and TIG welding.

The welding rectifiers can be used with the following remote control devices:

PHA 1, PHA 2, PHA 5, PHB 1, PHB 2, och PHC 2.

An auxiliary control unit is required for TIG welding with high frequency arc ignition.

LHF 400/630, versions with meters and timed cooling fan.

These welding rectifiers are equipped with a volmeter, ammeter and a circuit that

reduces the idle speed of the cooling fan.

The meters allow current and voltage settings to be read from the front of the

rectifier.

To minimise the amount of dust and dirt that is drawn into the rectifier the fan runs at

a reduced idle speed of 00 rpm. When welding with currents greater than 0 A the

fan speed increases to its working speed of around 1 50 rpm. A timer relay

maintains the higher speed setting for 6 1/2 minutes after welding has stopped to

ensure adequate cooling of the rectifier.

4 ECHNICAL DA A

LHF 400 LHF 630 LHF 800

Maximum load

5 % duty cycle 400 A/ 6 V 6 0 A/44 V 800 A/44 V

60 % duty cycle 15 A/ V 500 A/40 V 6 0 A/44 V

100 % duty cycle 250 A/ 0 V 400 A/ 6 V 500 A/40 V

Setting range 8A/20V--400A/ 6V 8A/20V--6 0A/44(49)

V8A/20V--800A/44(50)

Open circuit volt. 80--87 V 65--72 V 65--72 V

Open circuit output

at 400 V 40 W 615 W 640 W

Power factor

(max current) 0,90 0,87 0,82

Efficiency

(max current) 74 % 77 % 78 %

Enclosure class IP 2 IP 2 IP 2

Application class

Weight 195 kg 260 kg 295 kg

Dimens. lxwxh 1 10/765/705 1 10/765/705 1 10/765/705

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

-- 6 --

bh10d1 e

5 INS ALLA ION

The installation must be executed by a professional.

Note

Connect the power source to the electricity mains with a network impedance of 0.256

Ω

(LHF 400) 0.127

Ω

(LHF 630) or lower. If the network impedance is higher there is a risk of flicker in the illuminators.

WARNING!

This product is intended for industrial use. In a domestic environment this product may cause radio

interference. It is the user’s responsibility to take adequate precautions.

The power supply should be lifted by means of its lifting

eye. The handle is only intended for pulling it along the

ground.

Lifting instructions

SInstallation must be carried out by a qualified electrician.

SCheck that the welding rectifier is configured for the available mains supply before connecting it

to the mains.

SSee Connecting to mains for cable rating and fuse rating.

SConnect the mains cable to the rectifier according to the relevant regulations and install a suitable

fuse in the main fuse box.

SMake sure the welding rectifier is not covered or positioned so that cooling is obstructed.

5.1 Connecting to mains

LHF 400 LHF 630 LHF 800

Frequency 50 Hz 50 Hz 50 Hz

Voltage 400/415/500 V 400/415/500 V 400/415/500 V

Current at

100% duty cycle 19/19/16 A 8/ 8/ 0 A 49/49/40 A

60% duty cycle 24/24/20 A 47/47/ 8 A 62/60/50A

5% duty cycle 1/ 1/25 A 59/59/47A 79/79/6 A

Fuse, slow 25/25/20 A 50/50/ 5 A 6 /6 /50A

Cable area (4xmm2) 4/4/2,5 10/10/6 10/10/10

LHF 400 LHF 630 LHF 800

Frequency 60 Hz 60 Hz 60 Hz

Voltage 440/550V 440/550V 440/550V

Current at

100% duty cycle 19/16 A 8/ 0 A 49/40 A

60% duty cycle 24/20 A 47/ 8 A 62/50 A

5% duty cycle 1/25 A 59/47 A 79/6 A

Fuse, slow 25/20 A 50/ 5 A 6 /50 A

Cable area (4xmm2) 4/2,5 10/6 10/10

Cable areas comply with Swedish regulations.

-- 7 --

bh10d1 e

6 OPERA ION

SSet switch (1) to position ”I”. The white lamp (2) will light and the fan will start.

SSelect the welding method using the toggle switch ( ).

SAdjust the welding current using the knob (7) on the front, and set the toggle

switch (8) to the position nearest the socket.

SSelect suitable earth and return cables and connect them to the terminals

marked + and -- on the front of the rectifier. Connect the return cable to the work

piece.

SThe rectifier is now ready for welding.

6.1 Controls and connections

1. On/Off

2. White lamp (power on)

. Method selector switch

4. Arc air gouging

5. MMA

6. TIG

7. Current setting

8. Remote switch

9. Remote socket

10. Yellow lamp (thermal cut--out)

The yellow lamp comes on when the thermal cut--out trips.

When the rectifier has cooled down the thermal cut -- out is automatically reset.

bh10d001

-- 8 --

bh10d1 e

7 MAIN ENANCE

Note

All guarantee undertakings from the supplier cease to apply if the customer himself

attempts any work in the product during the guarantee period in order to rectify any

faults.

Only those persons who have appropriate electrical knowledge (authorised

personnel) may remove the safety plates to connect or carry out service

maintenance or repair work on welding equipment.

Cleaning

Check regularly that the power source is free from dirt.

How often, and to what extent, cleaning should be carried out depends on the

welding process, arc time, disposition and the surrounding environment. It will

normally suffice to blow the power source clean using compressed air (reduced

pressure) once a year.

If the power source is very dirty, brushing and vacuuming are recommended.

SDisconnect the welding power source from the mains current supply.

SRemove the adapter from the socket. Lock the socket to prevent unauthorised

connection.

At fixed installations, the safety switch should be set to the off position. Lock

the switch.

SRemove the power source’s safety plates for best access.

After cleaning, all safety plates must be mounted before you connect the power

source to the mains supply.

8 ORDERING OF SPARE PAR S

LHF 400, LHF 630, LHF 800 is designed and tested in accordance with the international

and European standards IEC/EN 60974--1 and EN 60974--10. It is the obligation of the

service unit which has carried out the service or repair work to make sure that the pro-

duct still conforms to the said standard.

Spare parts may be ordered through your nearest ESAB dealer, see the last page of

this publication.

-- 9 --

bh10a12a

bh10d002

LHF 400, LHF 630, LHF 800

Edition 070108

-- 10 --

lhf_or

Valid for serial no. 318, 318, 329--XXX--XXXX

Ordering numbers

0 19 78 882 LHF 400 400/415/500V 50Hz, 440/550V 60Hz

0 19 78 886 LHF 400 Offshore 400/415/500V 50Hz, 440/550V 60Hz

0 19 950 882 LHF 6 0 400/415/500V 50Hz, 440/550V 60Hz

0 19 950 886 LHF 6 0 Offshore 400/415/500V 50Hz, 440/550V 60Hz

0 19 951 884 LHF 800 Offshore 400/415/500V 50Hz, 440/550V 60Hz

Andere Handbücher für LHF 400

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB MIG400iCCCV Bedienungsanleitung

ESAB

ESAB Origo Tig 3001i Bedienungsanleitung

ESAB

ESAB RS 400x Bedienungsanleitung

ESAB

ESAB Multimaster 300 Bedienungsanleitung

ESAB

ESAB EMP 215ic Bedienungsanleitung

ESAB

ESAB A2 Multitrac Bedienungsanleitung

ESAB

ESAB PLASMAWELD 202 Bedienungsanleitung

ESAB

ESAB ROBUSTFEED EDGE Bedienungsanleitung

ESAB

ESAB Aristo Mig C3000i Bedienungsanleitung

ESAB

ESAB m3 Plasma EPP-202 Bedienungsanleitung

ESAB

ESAB A2 Multitrac Leitfaden

ESAB

ESAB ARC 601i Bedienungsanleitung

ESAB

ESAB MobileFeed 201 AVS Bedienungsanleitung

ESAB

ESAB Powercut 900 Bedienungsanleitung

ESAB

ESAB Renegade ET 180iP Bedienungsanleitung

ESAB

ESAB PT-36 Bedienungsanleitung

ESAB

ESAB Caddy Tig 1500i Bedienungsanleitung

ESAB

ESAB Aristo Origo Feed 3004 Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

ESAB

ESAB MIG C250i Bedienungsanleitung

ESAB

ESAB ST-21 Bedienungsanleitung

ESAB

ESAB ESP-200 Bedienungsanleitung

ESAB

ESAB TAF 1251 Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung